1996 TOYOTA TERCEL drain bolt

SS0KQ-04
- SERVICE SPECIFICATIONSMANUAL TRANSAXLE
SS-27
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Transaxle x Engine 17 mm head
14 mm head
10 mm head64
46
7.4650
470
7547
34
65 in.´lbf
Engine left mounting bracket x Insulator4849036
Engine rear mounting insulator x Body7880058
Engine rear mounting insulator x Bracket B bolt
C bolt64
90650
92047
67
Front exhaust pipe clamp set bolt1919014
Front exhaust pipe x Exhaust manifold6263046
Starter x Transaxle3940029
Clutch release cylinder x Transaxle121209
Shift lever assembly x Body121209
Grommet retainer x Body4.95043 in.´lbf
Retainer x Body4.95043 in.´lbf
Output shaft front bearing lock plate set bolt1111 58
Transmission case x Transaxle case2930022
Reverse shift arm bracket1717513
Straight screw plug (Reverse restrict pin) (C151)
Straight screw plug13
13130
1309
9
Straight screw plug (Shift fork shaft)2525018
Straight screw plug (Lock ball assembly) (C151)
Straight screw plug (C141)39
39400
40029
29
Reverse idler gear shaft lock bolt2930022
Rear bearing retainer2728020
Output shaft lock nut11 81,20087
Shift fork and shift head x Shift fork shaft1616012
Shift and select lever assembly2020014
Transmission case x Transmission case cover1818513
Back-up light switch4041030
Filler and drain plugs3940029
Ring gear x Differential case1241,26091
Speedometer driven gear1111 58
Control lever housing support bracket x Transmission case1111 58
Selecting bellcrank assembly x Transmission case2525018
Shift and select lever shaft assembly lock bolt2930022
Transaxle case receiver x Transaxle case1111 58
No. 1 and No. 2 oil receiver pipe1717513

SS0LL-04
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A132L)
SS-29
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Oil pan drain plug4950036
Oil pan4.95043 in.´lbf
Detent spring101007
Valve body x Oil pipe clamp101007
Valve body x Oil strainer101007
Valve body x Apply pipe bracket101007
Valve body x Transaxle101007
Park/neutral position switch x Transaxle case (bolt)5.45548 in.´lbf
Park/neutral position switch (nut)6.97061 in.´lbf
Transaxle control shaft lever x Park/neutral position switch131309
Transaxle control shaft lever x Transaxle control cable121209
Drive plate x Crankshaft8890065
Torque converter clutch x Drive plate2728020
Starter3940029
Transaxle housing x Engine (upper side)6465047
Transaxle housing x Engine (lower side) Bolt A
Bolt B
Bolt C
Bolt D7.4
25
46
6475
250
470
65065 in.´lbf
18
34
47
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Oxygen sensor4445032
Exhaust pipe clamp1919014
LH engine mounting x Body4949036
Engine rear mounting bracket x Engine rear mounting insulator6565048
Engine rear mounting insulator x Body Bolt A
Bolt B80
92800
92059
69

SS0LJ-04
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A242L)
SS-31
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Oil pan drain plug1717513
Oil pan4.95043 in.´lbf
Detent spring101007
Valve body x Oil pipe clamp101007
Valve body x Oil strainer101007
Valve body x Apply pipe bracket101007
Valve body x Transaxle101007
Park/neutral position switch x Transaxle case (bolt)5.45548 in.´lbf
Park/neutral position switch (nut)6.97061 in.´lbf
Transaxle control shaft lever x Park/neutral position switch131309
Transaxle control shaft lever x Transaxle control cable121209
Drive plate x Crankshaft8890065
Torque converter clutch x Drive plate2728020
Starter3940029
Transaxle housing x Engine (upper side)6465047
Transaxle housing x Engine (lower side) Bolt A
Bolt B
Bolt C7.4
64
4675
650
47065 in.´lbf
47
34
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Oxygen sensor4445032
Exhaust pipe clamp1919014
LH engine mounting x Body4949036
Engine rear mounting bracket x Engine rear mounting insulator6565048
Engine rear mounting insulator x Body Bolt A
Bolt B80
92800
92059
69

P20160
EM1OF-01
P20577
P20290
- ENGINE MECHANICALCYLINDER HEAD
EM-23
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE RH ENGINE UNDER COVER
2. DRAIN ENGINE COOLANT
3. DISCONNECT FRONT EXHAUST PIPE
Remove the 2 bolts and 2 compression springs, and disconnect
the front exhaust pipe.
4. A/T:
DISCONNECT THROTTLE CABLE
5. DISCONNECT ACCELERATOR CABLE
6. REMOVE AIR CLEANER ASSEMBLY WITH AIR IN-
TAKE CONNECTOR
7. DISCONNECT FUEL HOSE
Remove the union bolt and gaskets, and disconnect the fuel in-
let hose.
NOTICE:
Catch leaking fuel in a container.
8. w/ PS:
REMOVE PS PUMP AND PUMP BRACKET WITHOUT
DISCONNECTING HOSES
(a) Loosen the 2 bolts, and remove the PS drive belt.
(b) Remove the 2 bolts, and disconnect the PS pump from
the engine.
HINT:
Put aside the PS pump, and suspend it.
(c) Remove the 3 bolts and PS pump bracket.

EM1OH-01
- ENGINE MECHANICALENGINE UNIT
EM-57
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE BATTERY
2. REMOVE HOOD
3. REMOVE ENGINE UNDER COVERS
4. DRAIN ENGINE COOLANT
5. DRAIN TRANSAXLE OIL (FLUID)
6. REMOVE AIR CLEANER ASSEMBLY WITH AIR IN-
TAKE CONNECTOR
7. REMOVE RADIATOR (See page CO-16)
8. DISCONNECT ACCELERATOR CABLE
9. DISCONNECT FUEL HOSE
Remove the union bolt and gaskets, and disconnect the fuel in-
let hose.
NOTICE:
Catch leaking fuel in a container.
10. REMOVE CHARCOAL CANISTER
(a) Disconnect the canister hoses.
(b) Remove the charcoal canister.
11. DISCONNECT HOSES
(a) Disconnect the brake booster vacuum hose.
(b) Disconnect the MAP sensor hose.
(c) Disconnect the heater hoses.
12. DISCONNECT SPEEDOMETER CABLE FROM
TRANSAXLE
13. w/ PS:
DISCONNECT IDLE-UP AIR HOSES FROM AIR CON-
TROL VALVE
14. DISCONNECT ENGINE WIRE HARNESS
Disconnect these connectors and wires:

Main heated oxygen sensor connector

Oil pressure switch connector

SF1PX-01
(a)
(b)
(a)
(b)
(c)(d)(e)
MF-28
- MFITHROTTLE BODY
1996 TERCEL (RM440U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. REMOVE AIR CLEANER CAP
3. DISCONNECT CONTROL CABLES FROM THROTTLE
BODY
(a) Disconnect the accelerator cable
(b) Disconnect the A/T throttle cable.
4. REMOVE THROTTLE BODY
(a) Disconnect the throttle position sensor connector and
wire clamp.
(b) Disconnect the IAC valve connector.
(c) Disconnect the vacuum hose (from upper port of TVV of
EVAP) from port ºPº of throttle body.
(d) Disconnect the vacuum hose (from port ºPº of EGR vacu-
um modulator) from port ºEº of throttle body.
(e) Disconnect the vacuum hose (from port ºRº of EGR vacu-
um modulator) from port ºRº of throttle body.
(f) Remove the 2 nuts and 2 bolts.
Torque: 19.5 N´m (195 kgf´cm, 14 ft´lbf)
(g) Disconnect the throttle body from the intake manifold.
(h) Remove the gasket.
HINT:
At the time of installation, plaese refer to the following items. At-
tach a new gasket to the intake manifold, facing the protrusion
downward.

CO0HT-04
P21028
(b)
(c)
(a)
P21132
(2)(1)(b)
(a)
P21130
P21029
CO-4
- COOLINGWATER PUMP
1996 TERCEL (RM440U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. REMOVE GENERATOR
3. REMOVE INTAKE MANIFOLD STAY
(a) Disconnect the engine wire clamps from the intake man-
ifold stay.
(b) Remove the bolt, nut and intake manifold stay.
4. REMOVE WATER INLET PIPE
(a) Disconnect the water inlet hose.
(b) Disconnect the heater inlet hose.
(c) Disconnect the water bypass hose.
(d) Remove the bolt, water inlet pipe and O-ring.
5. REMOVE OIL DIPSTICK GUIDE AND GENERATOR
ADJUSTING BAR
(a) Disconnect the engine wire clamp.
(b) Disconnect the connector clamp for crankshaft position
sensor.
(c) Remove the oil dipstick.
(d) Remove the mounting bolt of the dipstick guide clamp and
generator adjusting bar.
(e) Pull out the dipstick guide. Plug the guide installation hole
of the oil pump.
(f) Remove the O-ring from the dipstick guide.
6. REMOVE WATER PUMP
Remove the bolt, 2 nuts and water pump.

CO0Y2-02
(b)
(a)
P20609
(c)(d)
P20754
Plug
(e)
P20755
A/T
(A)
P20610
Radiator Lower Hose
Radiator Lower Support CO-16
- COOLINGRADIATOR
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE ENGINE UNDER COVERS
2. DRAIN ENGINE COOLANT
3. REMOVE RADIATOR RESERVOIR TANK ASSEMBLY
4. REMOVE RADIATOR ASSEMBLY
(a) Disconnect the No.1 cooling fan connector.
(b) w/ A/C:
Disconnect the No.2 cooling fan connector.
(c) Disconnect the radiator upper hose from the radiator.
(d) Disconnect the radiator lower hose from the water inlet.
(e) Disconnect the 2 A/T oil cooler hoses from the radiator.
HINT:
Plug the hose to prevent oil from escaping.
(f) Remove the 2 bolts and 2 upper radiator supports.
Torque: 12 N´m (120 kgf´cm, 9 ft´lbf)
HINT:
(A/T only):
After installation, check that the rubber cushion (A) of the sup-
port is not depressed.
(g) Remove the radiator assembly.
(h) Remove the 2 radiator lower supports and the lower ra-
diator hose.