1996 TOYOTA TERCEL wiper fluid

MA001-24
- MAINTENANCEOUTSIDE VEHICLE
MA-1
39 Author
: Date
:
1996 TERCEL (RM440U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge.
If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing nuts.
If necessary, tighten them.
4. TIRE ROTATION
Check the owner's manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean.
If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, have the cause found and corrected.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and includiing the trunk lid operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.

BE-4
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
1996 TERCEL (RM440U) Taillight does not light up. (Headlight does not light up)
1. Light Control Switch
2. Headlight Bulb
3. Wire HarnessBE-16
-
-
Headlight does not light up with light control SW in HEAD.
1. Light Control Switch
2. D.R.L. Main Relay
3. D.R.L. No.4 Relay (R/B No.5)
4. Daytime Resistor
5. Wire HarnessBE-16
BE-16
BE-16
BE-16
-
Headlight does not go out with light control SW in OFF.1. Headlight Control Relay (Engine Room R/B)
2. Wire HarnessBE-16
-
Taillight does not light up with light control SW in TAIL.
1. Taillight Control Relay (I/P J/B)
2. Light Control Switch
3. Wire HarnessBE-16
BE-16
-
Taillight does not go out with light control SW in OFF.
1. Taillight Control Relay (I/P J/B)
2. Light Control Switch
3. Wire HarnessBE-16
BE-16
-
Headlight do not light up with engine running and light control SW
in OFF.
1. DOME Fuse (Engine Room R/B)
2. ECU-IG Fuse (I/P J/B)
3. DRL Fuse (Engine Room R/B)
4. D.R.L. Main Relay
5. D.R.L. No.4 Relay (R/B No.5)
6. Daytime Resistor
7. Wire Harness
8. Generator L Terminal
9. Parking Brake Switch
10.Brake Fluid Level Warning Switch-
-
-
BE-16
BE-16
BE-16
-
-
BE-38
BE-38
TURN SIGNAL AND HAZARD WARNING SYSTEM
TroubleParts nameSee page
ºHazardº and ºTurnº do not light up.
1. Hazard Warning Switch
2. Turn Signal Flasher
3. Wire HarnessBE-22
BE-22
-
No of blinks for Hazard.
(Turn is abnormal)1. Bulb
2. Turn Signal Flasher
3. Wire Harness-
BE-22
-
Hazard warning light does not light up.
(Turn signal is normal)1. HAZ-HORN Fuse (Engine Room R/B)
2. Wire Harness-
-
Hazard waning light does not light up in one direction.1. Hazard Warning Switch
2. Wire HarnessBE-22
-
Turn signal does not light up.
(Combination meter, wiper and washer do not operate.)
1. Ignition Switch
2. TURN Fuse (Engine Room R/B)
3. Turn Signal Switch
4. Wire HarnessBE-1 1
-
BE-22
-
Turn signal does not light up.
(Combination meter, wiper and washer are normal.)1. TURN Fuse (Engine Room R/B)
2. Turn Signal Switch
3. Wire Harness-
BE-22
-

BE-6
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
1996 TERCEL (RM440U) Washer fluid does not operate.
1. Washer Hose and Nozzle-

At wiper switch HI position, the wiper blade is in contact with the
body.

When the wiper switch is OFF, the wiper blade does not retract
or the retract position is wrong.
1. *1 Wiper Switch
2. Wire harnessBE-30
-
*1: Inspect wiper arm and blade set position
COMBINATION METER (METER, GAUGES AND ILLUMINATION)
TroubleParts nameSee page
Tachometer, Fuel Gauge and Engine Coolant Temperature Gauge
do not operate.3. GAUGE Fuse (Engine Room R/B)
4. Meter Circuit
5. Wire Harness-
BE-35
-
Speedometer does not operate.
1. Vehicle Speed Sensor
2. Meter Circuit
3. Wire HarnessBE-38
BE-35
-
Tachometer does not operate.
1. Igniter
2. ECM
3. Meter Circuit
4. Wire Harness-
-
BE-35
-
Fuel Gauge does not operate or operate abnormally.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Meter Circuit
4. Wire HarnessBE-38
BE-38
BE-35
-
Engine Coolant Temperature Gauge does not operate or operate
abnormally.
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Meter Circuit
4. Wire HarnessBE-38
BE-38
BE-35
-
All illumination lights do not light up.
1. TAIL Fuse (I/P J/B)
2. Light Control Rheostat
3. Meter Circuit
4. Wire Harness-
BE-38
BE-35
-
Only one illumination light does not light up.1. Bulb
2. Meter Circuit-
BE-35
COMBINATION METER (WARNING LIGHTS)
TroubleParts nameSee page
Warning lights do not light up.
(Except Discharge, SRS and Door Open)
1. Bulb
2. GAUGE Fuse (I/P J/B)
3. Ignition Switch
4. Meter Circuit
5. Wire Harness-
-
BE-1 1
BE-35
-
Brake Warning Light does not light up.
1. Bulb
2. Brake Fluid Level Warning Switch
3. Parking Brake Switch
4. Bulb Check Relay
5. Meter Circuit
6. Wire Harness-
BE-38
BE-38
-
BE-35
-
Seat Belt Warning Light does not light up.
1. Bulb
2. Seat Belt Retractor Switch
3. Integration Relay
4. Meter Circuit
5. Wire Harness-
BE-38
BE-38
BE-35
-

BO33S-01
N15577
A
C
BA
B
D E
BE3367
2 ~ 2.5 mm
(0.079 ~ 0.098 in.)
0.7 ~ 0.75 mm
(0.028 ~ 0.030 in.) BO-28
- BODYFRONT WIPER AND WASHER
1996 TERCEL (RM440U)
ADJUSTMENT
1. INSPECT WASHER NOZZLE
(a) While operating the washer, check whether the upper
point where the washer fluid hits the windshield and the
upsurge area are within the range indicated by the
hatched line.
A: Approx. 150 mm (5.91 in.)
B: Approx. 50 mm (1.99 in.)
C: Approx. 0 - 50 mm (0 - 1.99 in.)
D: Approx. 30 mm (1.18 in.)
E: Approx. 20 mm (0.79 in.)
(b) Check if the lower point where the washer fluid hits the
windshield is within the range of the wiping pattern (the
area of the glass which is wiped by the wiper blades).
2. ADJUST WASHER NOZZLE
Using a tool like that one shown in the illustration, change the
direction of the nozzle hole to adjust the point where washer
fluid hits the windshield.