1996 TOYOTA TERCEL lights

BE-6
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
1996 TERCEL (RM440U) Washer fluid does not operate.
1. Washer Hose and Nozzle-

At wiper switch HI position, the wiper blade is in contact with the
body.

When the wiper switch is OFF, the wiper blade does not retract
or the retract position is wrong.
1. *1 Wiper Switch
2. Wire harnessBE-30
-
*1: Inspect wiper arm and blade set position
COMBINATION METER (METER, GAUGES AND ILLUMINATION)
TroubleParts nameSee page
Tachometer, Fuel Gauge and Engine Coolant Temperature Gauge
do not operate.3. GAUGE Fuse (Engine Room R/B)
4. Meter Circuit
5. Wire Harness-
BE-35
-
Speedometer does not operate.
1. Vehicle Speed Sensor
2. Meter Circuit
3. Wire HarnessBE-38
BE-35
-
Tachometer does not operate.
1. Igniter
2. ECM
3. Meter Circuit
4. Wire Harness-
-
BE-35
-
Fuel Gauge does not operate or operate abnormally.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Meter Circuit
4. Wire HarnessBE-38
BE-38
BE-35
-
Engine Coolant Temperature Gauge does not operate or operate
abnormally.
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Meter Circuit
4. Wire HarnessBE-38
BE-38
BE-35
-
All illumination lights do not light up.
1. TAIL Fuse (I/P J/B)
2. Light Control Rheostat
3. Meter Circuit
4. Wire Harness-
BE-38
BE-35
-
Only one illumination light does not light up.1. Bulb
2. Meter Circuit-
BE-35
COMBINATION METER (WARNING LIGHTS)
TroubleParts nameSee page
Warning lights do not light up.
(Except Discharge, SRS and Door Open)
1. Bulb
2. GAUGE Fuse (I/P J/B)
3. Ignition Switch
4. Meter Circuit
5. Wire Harness-
-
BE-1 1
BE-35
-
Brake Warning Light does not light up.
1. Bulb
2. Brake Fluid Level Warning Switch
3. Parking Brake Switch
4. Bulb Check Relay
5. Meter Circuit
6. Wire Harness-
BE-38
BE-38
-
BE-35
-
Seat Belt Warning Light does not light up.
1. Bulb
2. Seat Belt Retractor Switch
3. Integration Relay
4. Meter Circuit
5. Wire Harness-
BE-38
BE-38
BE-35
-

- BODY ELECTRICALBODY ELECTRICAL SYSTEM
BE-7
1996 TERCEL (RM440U) Fuel Level Warning Light does not light up.
1. Bulb
2. Fuel Level Warning Switch
3. Meter Circuit
4. Wire Harness-
BE-38
BE-35
-
Low Oil Pressure Warning Light does not light up.
1. Bulb
2. Low Oil Pressure Warning Switch
3. Meter Circuit
4. Wire Harness-
BE-38
BE-35
-
Door Open Warning Light does not light up.
1. Bulb
2. DOME Fuse (Engine Room R/B)
3. Door Courtesy Switch
4. Meter Circuit
5. Wire Harness-
-
BE-38
BE-35
-
Discharge Warning Light does not light up.
1. Bulb
2. IGN Fuse (I/P J/B)
3. Generator
4. Meter Circuit
5. Wire Harness-
-
-
BE-35
-
COMBINATION METER (INDICATOR LIGHTS)
TroubleParts nameSee page
SRS Indicator Light does not light up.
1. Bulb
2. Wire Harness
3. Airbag Sensor Assembly-
-
DI-146
ABS Indicator Light does not light up.
1. Bulb
2. Wire Harness
3. ABS ECU-
-
DI-109
Malfunction Indicator Light does not light up.
1. Bulb
2. ECM
3. Wire Harness-
-
-
O/D OFF Indicator Light does not light up.
1. Bulb
2. O/D Main Switch
3. ECM
4. Meter Circuit
5. Wire Harness-
-
-
BE-35
-
Turn Indicator Light does not light up.
1. Bulb
2. Turn Signal and Hazard Warning System
3. Meter Circuit
4. Wire Harness-
BE-21
BE-35
-
High Beam Indicator Light does not light up.
1. Bulb
2. Headlight System
3. Meter Circuit
4. Wire Harness-
BE-13
BE-35
-
Security Indicator Light does not light up.
1. Bulb
2. Theft Deterrent System
3. Meter Circuit
4. Wire Harness-
DI-215
BE-35
-

BE0QU-01
I05914
D.R.L. : Daytime Running Light
* : CANADA Models OnlyEngine Room R/B

Headlight Control Relay

HEAD LH Fuse

HEAD RH Fuse

DOME Fuse

DIM M-Fuse

DRL Fuse
R/B No.5

D.R.L No.4 Relay

Headlight Dimmer Relay

HEAD LH-UPR Fuse

HEAD RH-UPR Fuse

HEAD LH-LWR Fuse

HEAD RH-LWR Fuse *
*
Combination Switch

Lignt Control Switch

Headlight Dimmer Switch*
* D.R.L. Main Relay
Door Courtesy Switch
Taillights I/P J/B

Integration Relay

Taillight Control Relay

TAIL Fuse

ECU-IG FuseHeadlights
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE-13
1035 Author
: Date
:
1996 TERCEL (RM440U)
HEADLIGHT AND TAILLIGHT SYSTEM
LOCATION

Z09752
From Back Side
Z08444
Z08449
N12797
BE-18
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
1996 TERCEL (RM440U)
(b) Connect the wire harness side connector to the relay and
inspect wire harness side connector from the back side,
as shown.
Tester connectionConditionSpecified condition
5 - GroundLight control switch OFF or TAILNo continuity
5 - GroundLight control switch HEADContinuity
17 - Ground* Headlight dimmer switch LONo voltage
17 - Ground* Headlight dimmer switch High or FlashBattery positive voltage
* With light control switch turned to HEAD
If circuit is as specified, try replacing the relay with a new one.
If circuit is not as specified, inspect the circuit connected to oth-
er parts.
7. INSPECT D.R.L. No.4 RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 - 2Continuity
Apply B+ between
terminals 1 and 2.3 - 4Continuity
If continuity is not as specified, replace the relay.
8. INSPECT DAYTIME RESISTOR RESISTANCE
ConditionTester connectionSpecified condition
Constant1 - 2Approx. 337 MW
If resistance is not as specified, replace the resistor
9. INSPECT INTEGRATION RELAY OPERATION
(a) Connect the positive (+) lead from the battery to terminal
3.
(b) Connect the negative (-) lead from the battery to termi-
nals 7 and 11.
(c) Check that the bulb lights and the chime sounds for 4 -
8 seconds.
(d) Return to step (a), and operate the chime again.

BE0R0-01
I05915
Engine Room R/B

HAZ-HORN Fuse
Hazard Warning Switch
Turn Signal and Hazard Warning Lights
Turn Signal Flasher
Turn Signal Switch
Ignition Switch
Turn Signal and Hazard Warning Lights I/P J/B

TURN Fuse
- BODY ELECTRICALTURN SIGNAL AND HAZARD WARNING SYSTEM
BE-21
1043 Author
: Date
:
1996 TERCEL (RM440U)
TURN SIGNAL AND HAZARD WARNING SYSTEM
LOCATION

BE0R1-02
Z11159
1 2 3
Z14865
BE1843
1 23
Turn Signal Light Bulbs (21W) BE-22
- BODY ELECTRICALTURN SIGNAL AND HAZARD WARNING SYSTEM
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT TURN SIGNAL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Left turn1 - 2Continuity
Neutral-No continuity
Right turn2 - 3Continuity
If continuity is not as specified, replace the switch.
2. INSPECT HAZARD WARNING SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF7 - 10Continuity
ON4 - 5 - 6 - 9
7 - 8Continuity
Illumination2 - 3Continuity
If continuity is not as specified, replace the switch.
3. INSPECT TURN SIGNAL FLASHER OPERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative (-) lead to terminal 3.
(b) Connect the two turn signal light bulbs parallel to each
other to terminal 1 and 3, and check that the bulbs flash.
HINT:
The turn signal lights should flash 60 to 120 times par minute.
If one of the front or rear turn signal lights has an open circuit,
the numbers of flashed will be more than 140 par minute.
If operation is not as specified, replace the flasher.

BE0R4-01
I05917
Ignition Switch
I/P J/B

GAUGE Fuse
Back-up Lights
Back-up Light Switch
Park/Neutral Position Switch
- BODY ELECTRICALBACK-UP LIGHT SYSTEM
BE-25
1047 Author
: Date
:
1996 TERCEL (RM440U)
BACK-UP LIGHT SYSTEM
LOCATION

BE0R6-01
I05918
Stop Light Switch
I/P J/B

STOP Fuse
High Mounted Stop Light
Stop Lights
- BODY ELECTRICALSTOP LIGHT SYSTEM
BE-27
1049 Author
: Date
:
1996 TERCEL (RM440U)
STOP LIGHT SYSTEM
LOCATION