1996 TOYOTA TERCEL Service Repair Manual

BE0R3-01
Z08452
Luggage Courtesy Switch
(Canada Only)ON
OFF
OFFON
N05342
N05343
BE-24
- BODY ELECTRICALINTERIOR LIGHT SYSTEM
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT DOOR COURTESY SWITCH CONTINUITY
(See page BE-38)
2. INSPECT LUGGAGE DOOR COURTESY SWITCH
CONTINUITY
(a) Check that there is continuity between terminal and the
switch body with the switch ON (switch pin released :
opened door).
(b) Check that there is no continuity between terminal and
the switch body with the switch OFF (switch pin pushed
in : closed door).
If operation is not as specified, replace the switch.
3. INSPECT ROOM LIGHT ASSEMBLY CONTINUITY
(a) Disconnect the connector from room light assembly.
(b) Turn the room light switch ON, check that there is continu-
ity between terminal 2 and body ground.
(c) Turn the room light switch DOOR, check that there is con-
tinuity between terminal 1 and 2.
If operation is not as specified, replace the switch.

BE0R4-01
I05917
Ignition Switch
I/P J/B

GAUGE Fuse
Back-up Lights
Back-up Light Switch
Park/Neutral Position Switch
- BODY ELECTRICALBACK-UP LIGHT SYSTEM
BE-25
1047 Author
: Date
:
1996 TERCEL (RM440U)
BACK-UP LIGHT SYSTEM
LOCATION

BE0R5-01
BE2682
BE-26
- BODY ELECTRICALBACK-UP LIGHT SYSTEM
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT BACK-UP LIGHT SWITCH CONTINUITY
Switch positionSpecified condition
PushContinuity
FreeNo continuity
If continuity is not as specified, replace the switch.
2. INSPECT PARK/NEUTRAL POSITION SWITCH CON-
TINUITY
(A132L: See page AX-2)
(A242L: See page AX-2)

BE0R6-01
I05918
Stop Light Switch
I/P J/B

STOP Fuse
High Mounted Stop Light
Stop Lights
- BODY ELECTRICALSTOP LIGHT SYSTEM
BE-27
1049 Author
: Date
:
1996 TERCEL (RM440U)
STOP LIGHT SYSTEM
LOCATION

BE0R7-01
Z08454
BE-28
- BODY ELECTRICALSTOP LIGHT SYSTEM
1996 TERCEL (RM440U)
INSPECTION
INSPECT STOP LIGHT SWITCH CONTINUITY
ConditionTester connectionSpecified condition
Brake pedal
depressed
(Switch pin free)
1 - 2Continuity
Brake pedal released
(Switch pin pushed in)-No continuity
If continuity is not as specified, replace the switch.

BE0R8-01
I05954
Wiper Motor
Washer Tank

Washer Motor
Combination Switch

Wiper and Washer Switch
I/P J/B

WIPER Fuse
- BODY ELECTRICALWIPER AND WASHER SYSTEM
BE-29
1051 Author
: Date
:
1996 TERCEL (RM440U)
WIPER AND WASHER SYSTEM
LOCATION

BE0R9-02
Z16294
N15560
N15561
Battery positive voltage
0 V 3.3 ± 1 sec.
N06459
BE-30
- BODY ELECTRICALWIPER AND WASHER SYSTEM
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT WIPER AND WASHER SWITCH CONTINU-
ITY
Switch positionTester connectionSpecified condition
Wiper OFF7 - 16Continuity
Wiper INT7 - 16Continuity
Wiper LO7 - 17Continuity
Wiper HI8 - 17Continuity
Washer ON2 - 11Continuity
If continuity is not as specified, replace the switch.
2. INSPECT INTERMITTENT OPERATION
(a) Turn the wiper switch to INT position.
(b) Connect the positive (+) lead from the battery to terminal
17 and the negative (-) lead to terminal 2.
(c) Connect the positive (+) lead from the voltmeter to termi-
nal 7 and the negative (-) lead to terminal 2, and check
that the meter needle indicates battery positive voltage.
(d) After connecting terminal 16 to terminal 17, connect 17 to
terminal 2.
Then, check that the voltage rises from 0 volt to battery
positive voltage within time as follows.
If operation is not as specified, replace the switch.
3. INSPECT WIPER MOTOR OPERATION
(a) Inspect the motor operation at low speed.
Connect the positive (+) lead from the battery to terminal
3 and the negative (-) lead from the battery to terminal 1,
and check that the motor operates at low speed.
If operation is not as specified, replace the motor.

N06460
N06461
N06462
BE4117
- BODY ELECTRICALWIPER AND WASHER SYSTEM
BE-31
1996 TERCEL (RM440U)
(b) Inspect the motor operation at high speed.
Connect the positive (+) lead from the battery to terminal
2 and the negative (-) lead from the battery to terminal 1,
and check that the motor operates at high speed.
If operation is not as specified, replace the motor.
(c) Inspect the motor operation when stopping it.
(1) Operate the motor at low speed and stop the motor
operation anywhere except at the stop position by
disconnecting positive (+) lead from terminal 3.
(2) Connect terminals 3 and 5.
(3) Connect the positive (+) lead from the battery to ter-
minal 6 and the negative (-) lead from the battery
to terminal 1, and check that the motor stops run-
ning at the stop position after the motor operates
again.
If operation is not as specified, replace the motor.
4. INSPECT WASHER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 2 and
the negative (-) lead to terminal 1, and check that the motor op-
erates.
NOTICE:
These tests must be performed quickly (within 20 seconds)
to prevent the coil from burning out.
If operation is not as specified, replace the motor.