1996 TOYOTA TERCEL weight

IN0II-01
Z14535
RearFront crossmember
Rear axle beam
Safety stand and swing arm type lift Front
Front
CAUTION:
Before jacking-up the front and rear, make sure the
car is not carrying any extra weight. JACK POSITION
PANTOGRAPH JACK POSITION
SUPPORT POSITION IN-8
- INTRODUCTIONREPAIR INSTRUCTIONS
1996 TERCEL (RM440U)
REPAIR INSTRUCTIONS
VEHICLE LIFT AND SUPPORT LOCATIONS

IN-32
- INTRODUCTIONTERMS
32 Author
: Date
:
1996 TERCEL (RM440U) CW
Curb Weight
DCDirect Current
DEFDefogger
DFLDeflector
DIFF.Differential
DIFF. LOCKDifferential Lock
D/INJDirect Injection
DLIDistributorless Ignition
DOHCDouble Over Head Cam
DPDash Pot
DSDead Soak
DSPDigital Signal Processor
EBDElectronic Brake Force Distribution
ECAMEngine Control And Measurement System
ECDElectronic Controlled Diesel
ECDYEddy Current Dynamometer
ECUElectronic Control Unit
EDElectro-Deposited Coating
EDICElectric Diesel Injection Control
EDUElectronic Driving Unit
EFIElectronic Fuel Injection
E/GEngine
EGR-VMExhaust Gas Recirculation-Vacuum Modulator
ELREmergency Locking Retractor
ENGEngine
ESAElectronic Spark Advance
ETCSElectronic Throttle Control System
EVPEvaporator
E-VR VElectric Vacuum Regulating Valve
EXHExhaust
FEFuel Economy
FFFront-Engine Front-Wheel-Drive
F/GFuel Gage
FIPGFormed In Place Gasket
FLFusible Link
F/PFuel Pump
FPUFuel Pressure Up
FrFront
FRFront-Engine Rear-Wheel-Drive
F/WFlywheel
FW/DFlywheel Damper
FWDFront-Wheel-Drive
GASGasoline
GSAGear Shift Actuator
GNDGround
HACHigh Altitude Compensator

EM1OD-01
P20154
Oil Pan
P20153
Ground Strap
P20536
Timing Mark
P20159
EM-12
- ENGINE MECHANICALTIMING BELT
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE RH ENGINE UNDER COVER
2. w/ A/C and/or w/ PS:
REMOVE DRIVE BELT
3. REMOVE GENERATOR DRIVE BELT
4. SLIGHTY JACK UP ENGINE
5. SLIGHTLY JACK UP ENGINE
Raise the engine enough to remove the weight from the engine
mounting on the right side.
6. REMOVE RH ENGINE MOUNTING INSULATOR
(a) Remove the bolt and disconnect the ground strap.
(b) Remove the through bolt, 2 bolts, nut and mounting insu-
lator.
7. REMOVE NO.2 TIMING BELT COVER
Remove the 4 bolts, timing belt cover and gasket.
8. SET NO.1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley, and align its groove with the
timing mark º0º of the No.1 timing belt cover.
NOTICE:
Always turn the crankshaft clockwise.
(b) Check that the hole of the camshaft timing pulley on the
side with the 5E mark is aligned with the timing mark of the
No.1 bearing cap.
If not, turn the crankshaft pulley 1 complete revolution (360°).
9. w/ A/C and/or w/ PS:
REMOVE NO.2 CRANKSHAFT PULLEY
Remove the 4 bolts and No.2 crankshaft pulley.

LU08F-04
LU0144
P21820
P21819
LU1165
- LUBRICATIONOIL PUMP
LU-1 1
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT PRESSURE REGULATOR VALVE
Coat the valve piston with engine oil and check that it falls
smoothly into the valve hole by its own weight.
If necessary, replace the valve.
2. INSPECT ROTOR BODY CLEARANCE
Using a feeler gauge, measure the clearance between the driv-
en rotor and pump body.
Standard clearance:
0.10 - 0.16 mm (0.0039 - 0.0063 in.)
Maximum clearance:
0.20 mm (0.0079 in.)
If the clearance is greater than maximum, replace the oil pump
rotor set and/or pump body.
3. INSPECT TIP CLEARANCE
Using a feeler gauge, measure the clearance between both ro-
tor tips.
Standard clearance:
0.03 - 0.14 mm (0.0012 - 0.0055 in.)
Maximum clearance:
0.20 mm (0.0079 in.)
If the clearance is greater than maximum, replace the oil pump
rotor set.
4. INSPECT SIDE CLEARANCE
Using a feeler gauge and flat block, measure the side clearance
as shown.
Standard clearance:
2.91 - 2.97 mm (0.1145 - 0.1169 in.)
Minimum clearance:
2.90 mm (0.1142 in.)
If the clearance is greater than maximum, replace the oil pump
rotor set and/or pump body.

SA128-02
FA1535
SST
F03986
SA-18
- SUSPENSION AND AXLEFRONT DRIVE SHAFT
1996 TERCEL (RM440U)
REMOVAL
NOTICE:

The hub bearing could be damaged if it is subjected
to the vehicle weight, such as when moving the ve-
hicle with the drive shaft removed. Therefore, if it is
absolutely necessary to place the vehicle weight on
the hub bearing, first support it with SST.
SST 09608-16042 (09608-02021, 09608-02041)

w/ ABS:
After disconnecting the drive shaft from the axle hub,
work carefully so as not to damage the sensor rotor
serrations on the drive shaft.
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. M/T:
REMOVE LH ENGINE UNDER COVER
3. DRAIN TRANSAXLE OIL (M/T) OR ATF (A/T)
4. w/ ABS:
REMOVE BOLT AND ABS SPEED SENSOR
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
5. REMOVE DRIVE SHAFT LOCK NUT
(a) Remove the cotter pin and lock cap.
(b) While applying the brakes, remove the nut.
Torque: 216 N´m (2,200 kgf´cm, 159 ft´lbf)
6. DISCONNECT TIE ROD END FROM STEERING
KNUCKLE (See page SA-10)
7. DISCONNECT LOWER BALL JOINT FROM LOWER
SUSPENSION ARM (See page SA-10)
8. DISCONNECT DRIVE SHAFT FROM AXLE HUB
NOTICE:
Be careful not to damage the drive shaft boot and inner oil
seal.

Z13632
R07591
Compressed Air
SR-28
- STEERINGPOWER STEERING VANE PUMP
1996 TERCEL (RM440U)
HINT:
There are 5 vane plate lengths with the following rotor and cam
ring marks:
Rotor and
cam ring markVane plate
part numberVane plate length
mm (in.)
None44345-1201014.996 - 14.998
(0.59039 - 0.59047)
144345-1202014.994 - 14.996
(0.59032 - 0.59032)
244345-1203014.992 - 14.994
(0.59024 - 0.59032)
344345-1204014.990 - 14.992
(0.59016 - 0.59024)
444345-1205014.988 - 14.990
(0.59008 - 0.59016)
3. INSPECT FLOW CONTROL VALVE
(a) Coat the valve with power steering fluid and check that it
falls smoothly into the valve hole by its own weight.
(b) Check the flow control valve for leakage. Close one of the
holes and apply 392 - 490 kPa (4 - 5 kgf/cm
2, 57 - 71 psi)
of compressed air into the opposite side hole, and confirm
that air does not come out from the end holes.
If necessary, replace the valve with the one having the same let-
ter as inscribed on the front housing.
Inscribed mark: A, B, C, D, E or F

R05752
SST
AB0164
R04211
Tires
(3 or more)Inner Diam.
Width RS-16
- SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
1996 TERCEL (RM440U)
(d) Install the SST.
CAUTION:
Place the disc wheel on level ground.
Connect the SST connector to the steering wheel pad
connector.
SST 09082-00700
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock. Also, pro-
vide some slack for the SST wire harness inside the disc
wheel.
(e) Cover the steering wheel pad with cardboard box or tires.

Covering method using cardboard box:
Cover the steering wheel pad with the cardboard
box and weight the cardboard box down in 4 places
with at least 190 N (20 kg, 44 lb).
Size of cardboard box:
Must exceed the following dimensions:
x= 460 mm (18.11 in.)
When dimension y of the cardboard box exceeds the
diameter of the disc wheel with tire to which the steer-
ing wheel pad is tied -
x= 460 mm (18.11 in.) + width of tire
y= 650 mm (25.59 in.)
NOTICE:
If a cardboard box smaller than the specified size is used,
the cardboard box will be broken by the shock of the airbag
deployment.

Covering method using tires:
Place at least 3 tires without disc wheel on top of the
disc wheel with tire to which the steering wheel pad
is tied.
Tire size: Must exceed the following dimensions-
Width: 185 mm (7.28 in.)
Inner diameter: 360 mm (14.17 in.)
CAUTION:
Do not use tires with disc wheels.