1996 TOYOTA TERCEL rear main

MA002-30
MA-2
- MAINTENANCEINSIDE VEHICLE
40 Author
: Date
:
1996 TERCEL (RM440U)
INSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. LIGHTS
(a) Check that the headlights, stop lights, taillights, turn signal lights, and other lights are all working.
(b) Check the headlight aim.
3. WARNING LIGHTS AND BUZZERS
Check that all warning lights and buzzers function properly.
4. HORN
Check that it is working.
5. WINDSHIELD
Check for scratches, pits or abrasions.
6. WINDSHIELD WIPER AND WASHER
(a) Check operation of the wipers and washer.
(b) Check that the wipers do not streak.
7. WINDSHIELD DEFROSTER
Check that air comes out from the defroster outlet when operating the heater or air conditioner.
8. REAR VIEW MIRROR
Check that it is mounted securely.
9. SUN VISORS
Check that they move freely and are mounted securely.
10. STEERING WHEEL
Check that it has the specified freeplay. Be alert for changes in steering condition, such as hard steering,
excessive freeplay or strange noises.
11. SEATS
(a) Check that all front seat controls such as seat adjusters, seatback reliner, etc. operate smoothly.
(b) Check that all latches lock securely in any position.
(c) Check that the locks hold securely in any latched position.
(d) Check that the head restraints move up and down smoothly and that the locks hold securely in any
latched position.
(e) For fold-down rear seat backs, check that the latches lock securely.
12. SEAT BELTS
(a) Check that the seat belt system such as the buckles, retractors and anchors operate properly and
smoothly.
(b) Check that the belt webbing is not cut, frayed, worn or damaged.

P19770
MA00S-13
MA-6
- MAINTENANCEBRAKE
44 Author
: Date
:
1996 TERCEL (RM440U)
BRAKE
INSPECTION
1. INSPECT BRAKE LINE PIPES AND HOSES
HINT:
Check in a well lighted area. Check the entire circumference
and length of the brake hoses using a mirror as required. Turn
the front wheels fully right or left before checking the front brake.
(a) Check all brake lines and hoses.

Check for damage.

Check for wear.

Check for deformation.

Check for cracks.

Check for corrosion.

Check for leaks.

Check for bends.

Check for twists.
(b) Check all clamps for tightness and connections for leak-
age.
(c) Check that the hoses and lines are clear of sharp edges,
moving parts and the exhaust system.
(d) Check that the lines installed in grommets pass through
the center of the grommets.
2. INSPECT FRONT BRAKE PADS AND DISCS (See page
BR-26)
HINT:
If a squealing or scraping noise comes from the brake during
driving, check the pad wear indicator to see if it is contacting the
disc. If so, the disc pad should be replaced.
3. INSPECT REAR BRAKE LININGS AND DRUMS (See
page BR-32)

P21589
SA3501
Grease
RA0489
MA-8
- MAINTENANCECHASSIS
46 Author
: Date
:
1996 TERCEL (RM440U)
(b) Check the dust cover for damage.
6. CHECK TRANSAXLE OIL (FLUID)
Visually check the transaxle for oil (fluid) leakage.
If leakage is found, check for the cause and repair.
7. REPLACE TRANSAXLE OIL (FLUID)
(a) M/T:
Replace the transaxle oil (See page MX-6).
(b) A/T:
Replace the transaxle fluid.
(A132L: See page AX-2)
(A242L: See page AX-2)
8. REPACK REAR WHEEL BEARINGS
(a) Change rear wheel bearing grease.
(1) Remove the hub and inner and outer bearings.
Clean in solvent and inspect the bearings for dam-
age.
(2) Pack the bearings and axle hubs with multipurpose
grease.
Wheel bearing grease grade:
Lithium base multipurpose grease (NLGI No.2)
(b) Install inner bearing and new oil seal.
(c) Install the hub and adjust the wheel bearing preload (See
page SA-42).
Preload (while turning):
Add frictional force plus
0 - 11.8 N (0 - 1.2 kgf, 0 - 2.6 lbf)

MA02M-05
- MAINTENANCEBODY
MA-9
47 Author
: Date
:
1996 TERCEL (RM440U)
BODY
INSPECTION
1. TIGHTEN BOLTS AND NUTS ON CHASSIS AND BODY
(a) Tighten the front seat-to-body mounting bolts.
Torque: 37 N´m (375 kgf´cm, 27 ft´lbf)
(b) Under Severe Conditions:
In addition to the above maintenance items, check for
loose or missing nuts and bolts on the steering system,
drive train, suspension system, fuel tank mounts, engine
mounts, etc.
2. FINAL INSPECTION
(a) Check the operation of the body parts:

Hood:
Auxiliary catch operates properly
Hood locks securely when closed

Front and rear doors:
Door lock operates properly
Doors close properly

Luggage compartment door:
Door lock operates properly

Seats:
Seat adjusts easily and locks securely in any posi-
tion
Front seat back locks securely in any position
Folding-down rear seat backs lock securely
(b) Road test:

Check the engine and chassis for abnormal noises.

Check that the vehicle does not wander or pull to
one side.

Check that the brakes work properly and do not
drag.
(b) Be sure to deliver a clean car.
Especially check the steering wheel, shift lever knob, all
switch knobs, door handles and seats.

SS0N2-05
- SERVICE SPECIFICATIONSSTEERING
SS-37
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
STEERING COLUMN
Steering support x Column tube5.45548 in.´lbf
Control valve shaft x Sliding yoke2526019
Steering main shaft x Sliding yoke2526019
Steering column assembly set nut2526019
Steering wheel set nut3435025
Steering wheel pad set screw8.89078 in.´lbf
PS VANE PUMP
Pressure port union x Front housing6970051
Suction port union x Front housing131309
Pressure feed tube x Pressure port union5455040
PS vane pump pulley set nut4344032
PS vane pump assembly set nut Bolt A4344032 PS vane um assembly set nut Bolt A
Bolt B
43
39
440
400
32
30
MANUAL STEERING GEAR
Pinion bearing adjusting screw lock nut for use with SST
for use without SST85
11 3871
1,15063
83
Rack guide spring cap lock nut for use with SST
for use without SST41
56419
57530
42
Rack x Rack end for use with SST
for use without SST43
59434
60031
43
Tie rod end lock nut4748035
Manual steering gear bracket x Body5859043
Pinion shaft x Sliding yoke2526019
Steering main shaft x Sliding yoke2526019
Column hole cover x Body4.95043 in.´lbf
PS GEAR
Cylinder end stopper5960043
Self-locking nut5960043
Rack housing cap5960043
Rack guide spring cap lock nut for use with SST
for use without SST31
44316
45023
33
Rack x Rack end for use with SST
for use without SST43
59434
60031
43
Tie rod end lock nut4748035
Turn pressure tube union nut for use with SST
for use without SST20
25203
25015
18
Air control valve2930022
PS gear bracket x Body5859043
Engine rear mount insulator Bolt A6465047 Engine rear mount insulator Bolt A
Bolt B
64
78
650
800
47
58
Engine rear mount bracket x Transaxle4849035
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe clamp1919014
Front exhaust pipe x Oxygen sensor4445032

EM9988
EM3441
P20487
EM9392
EM3444
- ENGINE MECHANICALCYLINDER BLOCK
EM-71
1996 TERCEL (RM440U)
16. REMOVE REAR OIL SEAL RETAINER
(a) Remove the 4 bolts.
(b) Using a screwdriver, remove the oil seal retainer by prying
the portions between the oil seal retainer and main bear-
ing cap.
17. CHECK CONNECTING ROD THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance while mov-
ing the rod back and forth.
Standard thrust clearance:
0.15 - 0.35 mm (0.0059 - 0.0138 in.)
Maximum thrust clearance:
0.45 mm (0.0177 in.)
If the thrust clearance is greater than maximum, replace the
connecting rod assembly. If necessary, replace the crankshaft.
18. REMOVE CONNECTING ROD CAPS AND CHECK OIL
CLEARANCE
(a) Check the matchmarks on the connecting rod and cap to
ensure correct reassembly.
(b) Remove the 2 connecting rod cap nuts.
(c) Using a soft-faced hammer, lightly tap the connecting rod
bolt and lift the cap and lower bearing.
HINT:
Keep the lower bearing inserted with the connecting rod cap.

AX07X-05
- AUTOMATIC TRANSAXLE (A242L)AUTOMATIC TRANSAXLE SYSTEM (A242L)
AX-13
1996 TERCEL (RM440U)
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
ON-VEHICLE:
SymptomSuspect AreaSee page
Does not move in any forward position
4. Forward clutch (C1)
5. No.2 one-way clutch (F
2)
6. 1st & reverse brake (B
3)
7. 2nd brake (B
2)
8. 2nd coast brake (B
1)
9. Direct clutch (C
2)












Does not move in reverse position
1. 2nd coast brake (B1)
2. Front planetary gear
3. Rear planetary gear
4. 1 - 2 shift valve
5. 2 - 3 shift valve
6. Direct clutch (C
2)
7. U/D clutch (C
3)
8. 1st and reverse brake (B
3)
















Does not move in any forward position or reverse position
1. Parking lock pawl
2. Manual valve
3. U/D one-way clutch (F
3)
4. U/D clutch (C
3)
5. U/D brake (B
0)
6. Front planetary gear
7. Rear planetary gear
8. U/D planetary gear
9. Torque converter clutch
















AX-34
No-up shift
(1st " 2nd)1. 1 - 2 shift valve
2. 2nd brake (B
2)
3. No.1 one-way clutch (F
1)






No-up shift
(2nd " 3rd)1. 2 - 3 shift valve
2. Direct clutch (C
2)




No-up shift
(3rd " O/D)1. U/D brake (B0)
2. 3 - 4 shift valve



No-down shift
(O/D " 3rd)3 - 4 shift valve

No-down shift
(3rd " 2nd)2 - 3 shift valve

No-down shift
(2nd " 1st)1. 1 - 2 shift valve
2. 2nd coast brake (B
1)




Shift point too high or too low
1. Governor valve
2. 1 - 2 shift valve
3. 2 - 3 shift valve
4. 3 - 4 shift valveAX-21






Up-shifts 3rd " O/D with O/D main switch ''OFF''Electric control systemAX-2
Harsh engagement
(N " R)1. Direct clutch (C2)
2. 1st & reverse brake (B
3)
3. Accumulator control valve






Harsh engagement
(N " D)1. Forward clutch (C1)
2. C
1 accumulator




Harsh engagement
(N " L)Low coast modulator valve

BE-8
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
1996 TERCEL (RM440U)
DEFOGGER SYSTEM
TroubleParts nameSee page
Rear window defogger does not operate.
(w/Timer)
1. DEF M-Fuse (I/P J/B)
2. GAUGE Fuse (I/P J/B)
3. Defogger Switch
4. Defogger Relay
5. Defogger Wire
6. Wire Harness-
-
BE-46
BE-46
BE-46
-
Rear window defogger does not operate.
(w/o Timer)
1. DEF M-Fuse (I/P J/B)
2. Defogger Switch
3. Defogger Wire
4. Wire Harness-
BE-46
BE-46
-
POWER WINDOW CONTROL SYSTEM
TroubleParts nameSee page
Power window does not operate.
(Door lock does not operate.)1. POWER M-Fuse (R/B No.7)
2. Wire Harness-
-
Power window does not operate.
(Door lock is normal.)
1. GAUGE Fuse (I/P J/B)
2. Ignition Switch
3. POWER M-Fuse (R/B No.7)
4. Power Main Relay (R/B No.7)
5. Power Window Master Switch
6. Wire Harness-
BE-1 1
-
BE-49
BE-49
-
ºOne Touch Power Window Systemº does not operate.1. Power Window Master SwitchBE-49
Only one window glass does not move.
1. Power Window Master Switch
2. Power Window Switch
3. Power Window Motor
4. Wire HarnessBE-49
BE-49
BE-49
-
ºWindow Lock Systemº does not operate.1. Power Window Master SwitchBE-49
ºWindow Lock Illuminationº does not light up.1. Power Window Master SwitchBE-49