1991 MITSUBISHI ECLIPSE Service Manual

FRONT SUSPENSION - Centermember and Crossmember2-49
CENTERMEMBER AND CROSSMEMBER
- REMOVAL AND INSTALLATIONNOZYA-B
40-50 Nm
29-36 ft.lbs.
50-65 Nm
36-47 ft.lbs.
\
80-I:0 Nm
58-72 ft.lbs.3'
/I-Y--
7t
/70-80Nm80-100 Nm151-58ft.lbs.58-72 ft.lbs.OlA0619
80-100 Nm70-80Nm58-72 ftlbs.51-58ftlbs.
-30 ll.l”S.,
e ~
70-80 Nm51-58
ft.lbs.7n-~0 NmI” .s- .w...51-58 ft.lbs.Removal steps
1. Cover installation screw
2.Left member3.Right member
4. Front roll stopper installation bolt
5.No. 1 crossmember
installation
nut
6.Lower plate7.No. 1 crossmember
8.
9.Bushing (B)10.GussetPost-installation Operation
l Air bleeding of the Power-steering Fluid(Refer to GROUP 19-Service
*Adjustment
P.2-8.)
NOTE
(I)(2) q : Non-reusable parts

2-50FRONT SUSPENSION -Centermember and Crossmember
40-60 Nm
29-43 ftlbs.
“1I
30-40 Nm
22-29 ftlbs.
40-60 /Nm29-43 ftlbs.
11. Front exhaust pipe rear installation bolts12. Gasket
13. Self locking nut
14. Front exhaust pipe
15. Gasket35-45
25-33
IO-15 Nm7- 11 ftlbs.
22-30 ftlbs.
12AO352
+e MI 16. Stabilizer link installation nut17.Stabilizerlink
18. Stabilizer bar bracket installation boltsl 19. Stabilizer bar bracket20.Bushing
4*21. Stabilizer bar
05AO169
$?everse the removal procedures to reinstall.(2) +* : Refer to “Service Points of Removal”.(3) l 4 : Refer to “Service Points of Installatron”.(4) m : Non-reusable partsA
A’A
ct
J’

FRONT SUSPENSION - Centermember and Crossmember2-51
\09*005555-60 Nm
2240-43 ftlbs.60-80 Nm
43-58
ftlbs.
15-20 Nm11-14 ft.lbs.
\2512-18 Nm
9-13
ft.lbs.a
22. Transfer assembly23. Cotter pin
24. Tie-rod end connection nut25. Joint assembly connection bolt
26. Return tube connection
27. Pressure hose connection28. Mounting bracket
+e l + 29. Steering gear box assembly
OlA047360-80 Nm
42-58
ft.lbs.
Fykeverse the removal procedures to reinstall.(2) ~~ : Refer to “Service Points of Removal”.(3) l + : Refer to “Service Points of lnstallatron”(4) m : Non-reusable parts

FRONT SUSPENSION - Centermember and Crossmember
34
40-50 Nm
29-36 ftlbs.
38
100-12072-87 ft32
;56-72 ft.lbs.-39
-36
‘350
’ 80-100 Nm
58-72 ft.lbs.
60-100 Nm*58-72 ft.lbs.*
30. Self locking nut
31.Clamp32. Lower arm mounting bolt
33.Stopper
34. Rear roll stopper bracket mounting bolt35. Self locking nut
36.Lower plate37.Crossmember38.Stopper
39.Spacer40.BushingNOTE(1) Reverse the removal procedures to reinstall.(2) m : Non-reusable parts(3) * Indicates parts which should be temporarily tightened,
and then fully tightened with the vehicle in the unladen
condition.
OlA0641

FRONT SUSPENSION - Centermember and Crossmember2-53SERVICE POINTS OF REMOVAL
NOZYBAF16. REMOVAL OF STABILIZER LINK INSTALLATION NUT/
21. STABILIZER BAR
Refer to
P.2-39.29. REMOVAL OF STEERING GEAR BOX ASSEMBLY
Refer to GROUP
19-Steering Gear Box.
INSPECTIONNOZYCAA2l Check the crossmember for cracks or deformation.
l Check the bushings for cracks or deterioration.
l Check the centermember for cracks or deformation.
BUSHING REPLACEMENTRefer to
P.2-48.
NOZYDABSERVICE POINTS OF INSTALLATION
N02YEAF29. INSTALLATION OF STEERING GEAR BOX ASSEMBLY
Refer to GROUP
19-Steering Gear Box.
19. INSTALLATION OF STABILIZER BAR BRACKET/
16. STABILIZER LINK INSTALLATION NUT
Refer to
P.2-41.

NOTES

3-1
REAR AXLE
CONTENTSAXLE SHAFT
...................................................10
DIFFERENTIAL CARRIER................................19DRIVE SHAFT
..................................................13SERVICE ADJUSTMENT PROCEDURES..
.....8
GearOilLevelCheck...................................8
LimitedSlipDifferentialCheck....................9
..Rear Axle Total Backlash Check.................8Rear Wheel Bearing End Play Check
.........
8Rear Wheel Bearing Rotation Sliding
ResistanceCheck.........................................9
SPECIALTOOLS.............................................4
SPECIFICATIONS.............................................
2
GeneralSpecifications..................................2
Lubricants......................................................3Sealants and Adhesives...............................
3Service
Specifications...................................2TorqueSpecifications...................................
3
TROUBLESHOOTING......................................6Axle Shaft
Grease leakageNoise while wheels are rotatingDifferential (Conventional Differential)
Bearing noise while driving or coasting
Constant noise
Gear noise while coasting
Gear noise while driving
HeatNoise while turning
Oil leakage
Differential (Limited Slip Differential)
Abnormal noise during driving or
gear changing
Abnormal noise when cornering
Break down
Gear noise
Gear oil leakage
SeizureThe limited slip differential does
not function
Drive Shaft
Noise

3-2REAR AXLE - Specifications
SPECIFICATIONS
GENERAL SPECIFICATIONSNO3CA- h
ItemsVehicles with
Vehicles with
conventional differential
limited slip differential
Axle shaft
TypeSemi-floating type
Semi-floating type
Shaft dimensions
Outer bearing portion dia.
mm (in.) 35 (1.38)
35 (1.38)
Inner bearing portion dia.
mm (in.) 28 (1.10)
28 (1.10)
Center portion dia.
mm (in.) 34.5 (1.36)
34.5 (1.36)
Overall length
mm (in.) 214.9 (8.46)
214.9 (8.46)
Bearing
O.D. x I.D.
Outer
mm (in.) 72 x 35 (2.83 x 1.38)
72 x 35 (2.83 x 1.38)
Innermm (in.) 58 x 28 (2.28 x 1.10)
58 x 28 (2.28 x 1.10)
Drive shaft
Joint type
Outer
D.O.J.D.O.J.
Inner
B.J.B.J.Length (joint to joint)
x diametermm (in.) 397 x 24 (15.6 x .94)397 x 24 (15.6 x .94)
DifferentialReduction gear type
Hypoid gearHypoid gear
Reduction ratio3.545
, 3.307
3.545 , 3.307 Differential gear type and configuration
Side gearStraight bevel gear
x 2Straight bevel gear x 2
Pinion gearStraight bevel gear
x 2Straight bevel gear x 4
Number of teeth
Drive gear39
. 43 39 , 43 Drive pinion
11 , 13 ll, 13
Side gear
1416Pinion gear
1010
NOTED.O.J.: Double offset joint
B.J.: Birfield joint
SERVICE SPECIFICATIONSNOBCB-
Items
Standard valueRear wheel bearing rotation sliding resistance
Setting of D.O.J. boot length
Final drive gear backlash
Differential gear backlash
Conventional differential
Limited slip differential
Drive pinion rotation starting torque
with oil seal
New part
New part/reusable part
without oil seal
New part
New part/reusable partSpecifications
N (Ibs.) [Nm (in.lbs.)l 12 (2.6) [0.7 (6)l or less
mm (in.)
76+3 (3.00+.12)
mm (in.) 0.1
l-0.16 (.004-,006)
mm (in.)O-0.076
(O-.003)
0.03-0.09 (.0012-.0035)
Nm
(in.lbs.)
1.0-1.3 (9-11)
0.5-0.6 (4-5)
Nm
(in.lbs.)
0.9-I .2 (8-10)
0.4-0.5 (3-4)
A