1991 MITSUBISHI ECLIPSE Service Manual

BODY - Quarter Window Glass23-61QUARTER WINDOW GLASS
N22LEAKPre-removal Operation
@Removal of Rear Side Trim, Quarter
Trim. Center Pillar Trim and Rear
IPillar’ Trim
I(Refer to
P.23-85.)l kemoval of Side Air SpoilerI(Refer to
P.23-74.)Iter Trim, Center Pillar Trim and Rear
Removal steps1. Quarter window moulding lower
2. Quarter window moulding upper
3. Quarter window moulding front
4. Quarter window glass
5. Quarter window moulding clipInstallation steps5. Quarter window moulding clip
l + 3. Quarter window moulding front
l * 4. Quarter window glass
2. Quarter window moulding upper1. Quarter window moulding lower
NOTE(1) l + : Refer to “Service Points of Installation”.(2) $ : Non-reusable parts
Quarter window glass
SECT.B-B and C-C
SECT. A-A
18AO521mm
(in.)18AO521
-ISERVICE POINTS OF INSTALLATION3. INSTALLATION OF QUARTER WINDOW
MOULDING
FRONT/4. QUARTER WINDOW GLASS
(1) Remove residual-sealant from the body and glass.
(2) Degrease the body and glass, and coat primer.
(Refer to
P.23-59.)
(3) Coat specified sealant on the indicated position of the
glass.Specified sealant: MOPAR Silicone Rubber Sealer
Part No.4626070 or Auto Glass
Adhesive and Sealer PartNo.2298825 or equivalent
(4) Mount the glass on the body.

23-62BODY - Liftgate Window Glass
LIFTGATE WINDOW GLASSN22LDAK
REMOVAL AND INSTALLATION
Pre-removal Operation*Removal of Liftgate Trim and Flange
Trim
(Refer to
P.23-86.)aRemoval of Air Spoiler
(Refer to P.23-74.)Post-installation Operation
*Installation of Air Spoiler
(Refer to
P.23-74.)*Installation of Liftgate Trim and
Flange Trim
(Refer to
P.23-86.)
I
Removal steps
I. Liftgate moulding upper
2. Liftgate moulding clip
3. Liftgate moulding lower
4. Liftgate moulding side
o*5. Liftgate window glass
6. Liftgate moulding fastener
7.
Liftgate moulding clip
Installation steps7.
Liftgate moulding clip
6.
Liftgate moulding fastener
M 4. Liftgate moulding side
w 5. Liftgate window glass
3.
Liftgate moulding lower
2. Liftgate moulding clip1. Liftgate moulding upper
WA0487NOTE
(1) l * : Refer to “Service Points of Removal”.(2) .+ : Refer to “Service Points of Installation”.(3) q : Non-reusable parts
SECT. A-A
SECT. B-B(Other areas not illustrated arethe same as those in cmss sec-
SECT. C-C(Other areas not illustrated are thesame as those ,ncrms sectmn A-A )1ar40525mm
(in.)
ISA0526
SERVICE POINTS OF REMOVAL5. REMOVAL OF
LIFTGATE WINDOW GLASS
Remove the quarter window glass in the same procedure as
the windshield glass. (Refer to
P.23-58.)
SERVICE POINTS OF INSTALLATION4. INSTALLATION OF
LIFTGATE WINDOW MOULDINGSIDE/5.
LIFTGATE WINDOW GLASS
Compared with the windshield glass, adhesive is coated onthe different position but the working procedure is same.
(Refer to
P.23-59.)

BODY - Door AssemblvDOOR ASSEMBLY
- REMOVAL AND INSTALLATION
N22MAW17-26
12-19
17-26
12-19
15A0511
Removal steps
1. Connection for door wiring harness
connector
*+ 2. Spring pin
3. Door assembly
l 4. Upper hinge
.c 5. Lower hinge6. Striker7. Striker shim
8. Door switch cap
9. Door switch
l * 10. Door check strap
0 Removal of Cowl Side Trim(Refer to P.23-85.)
l Installation of Cowl Side Trim(Refer to P.23-85.)
0 Door Adjustment
NOTE(I) Reverse the removal procedures to reinstall.(2) I)+ : Refer to “Service Points of Instal$tion”.

23-64BODY - Door AssemblyON-OFF
stroke
1*,,.$18A0158
Type BON-OFF
stroke
“1 /- 16PO192klBA0459
Identification mark
INSPECTIONDOOR SWITCH
Operate the switch, and check the continuity between the
T
terminals.TYPE A
123
Open (ON)0A
0
SwitchDepressed (OFF)
NOTEO-O indicates that there is continuity between the terminals.
TYPEB
12
Open (ON)00
Switch
Depressed (OFF)b
NOTEO-O indicates that there is continuity between the terminals.
SERVICE POINTS OF INSTALLATION10. APPLICATION OF GREASE TO DOOR CHECK STRAP/
5. LOWER HINGE/A UPPER HINGE12. SPRING PINApply multipurpose grease to all moving parts.A
Grease: MOPAR Multipurpose Grease Part No.
‘- -’2932524 or equivalent
DOOR CHECK STRAP REPLACEMENT1. Remove the door trim and waterproof film.
2. Press upward and remove spring pin.
3. Remove door check strap nuts. Remove door check strap.
4.With the identification mark upward, install door check strap.
5.After installation of the door check strap, apply a coating ofmultipurpose grease to the door check strap slide surface
and the spring pin (at the places shown in the figure).

BODY - Door Trim and Waterproof Film2345
DOOR TRIM AND WATERPROOF FILM
REMOVAL AND INSTALLATIONI
Power window provided vehicle%l \PL
< Oriver’s seat side>
2i36~4
15AO514<
Passenaer’s
seat
side >
er window provkkd
Removal steps2. Door window regulator handle
3. Escutcheon
4. Door grip mounting screw
5. Pull handle box
l *6. Door trim
l +1. Clip
7. Power window switchWA05138. Electrical remote control mirror switch
9. Door grip
10. Pull handle bracket
11. Door grip lower bracketNOTE
(1) Reverse the removal procedures to reinstall.12. Door trim bracket B(2) a* : Refer to “Service Points of Removal”.13. Door trim bracket
C(3) +* : Refer to “Service Points of Installa~lon”,
*c 14. Waterproof film(4) +shows the installation position of trim Clip.
I

23-66BODY - Door Trim and Waterproof Film/Door Glass and Regulator
SERVICE POINTS OF REMOVAL1. REMOVAL OF CUP
‘.+iUse a shop towel to remove the clip; and remove door
_Awindow regulator handle.
IbY ISealant!I6. REMOVAL OF DOOR TRIM
If clip remains in mounting hole provided in door, remby using tool manufactured as illustrated.ove it
SERVICE POINTS OF INSTALLATION14,APPLlCATlON OF SEALANT TO WATERPROOF FILM
Apply specified sealant at the position shown in the
illustration, and then attach the waterproof film.
/rSpecified sealant: MOPAR Rope Caulk Sealer
3/ --‘I16
X 80” roll Part No.4026044 or
equivalent
DOOR GLASS AND REGULATORIMOVAL AND INSTALLATION
Pre-removal Operationl Removal of Door Trim and Water-
proof Film
(Refer to P.23-65.)
l Removal of Front Door Belt Line In-
ner Weatherstrip
(Refer to P.23-72.)
N23MCAW2.0-4-O
Nm1.5-3.0 ft.lbs.
Removal steps1. Door window glass
2. Door glass holder
*4 3. Front door window regulator
4. Front door rear sash
NOTEII ) Reverse the removal procedures to reinstall.12) l + : Refer to “Service Points of Installation”
Post-installation Operation0 Installation nf Frnnt lhnr Rnlt I inn
l Installation of Door Trim and
0 Door Window Glass Adjustment

BODY - Door Glass and Reaulator/Power Window23-67
POWER WINDOW
REMOVAL AND INSTALLATIONSERVICE POINTS OF INSTALLATION3. APPLICATION OF GREASE TO FRONT DOOR WINDOW
REGULATORApply multipurpose grease to all moving parts.
Grease: MOPAR Multipurpose Grease Part No.
2932524 or equivalent
N23MHAEa
71l Door Window Glass Adjustment

< Passenger’s seat side >NOTE
(1) Reverse the removal procedures to reinstall.(2) l + : Refer to “Service Points of Installation”.
1810469Power window relay removal
1. Power window relay
Power window switch removal steps
Door trim (Refer to P.23-65.)2. Power window main switch
3. Power window sub switch
Power window motor removal steps
Door trim and waterproof film
(Refer to
P.23-65.)4. Door window glass
l + 5. Front door window regulator
16l.03443 416AO606
INSPECTIONPOWER WINDOW RELAY
Apply battery voltage to terminal 2, and check for continuity
when terminal 4 is grounded.
NOTEO-O indicates that there is continuity between the terminals.

23-68BODY - Power Window
Power
window
lock
switch
,POWER WINDOW MOTOR
(1) Connect the motor terminal directly to the battery and
check to be sure that the slider moves smoothly.
(2) Also check to be sure that the slider moves in the opposite
direction when the battery polarity connections are
changed.CIRCUIT BREAKER (INCORPORATED IN THE POWER
WINDOW
MOTOR)
(1) Press the UP switch to fully close the window glass, and
continue to press the switch for
10 seconds.
(2) At the moment that the UP switch is released, press the
DOWN switch. The circuit breaker can be considered goodif at this time the door window glass begins to open within
60 seconds.POWER WINDOW MAIN SWITCH
Check for continuity in accordance to the following connection
table.
NOTEO-O indicates that there is continuity between the terminals.