2020 MITSUBISHI L200 Owner's Manual (in English)

Power type*
1- To adjust forward or backwardOperate the switch as indicated by thearrows and adjust the seat to the desired
position.
2- To recline the seatback Operate the switch as indicated by thearrows and adjust the seatback angle to
the desired position.
3- To adjust seat height Operate the switch as indicated by thearrows and adjust the seat height to the
desired position.
If the entire switch is operated, then the entire seat moves.
4- To adjust seat cushion angle Operate the switch as indicated by thearrows and adjust the seat cushion angle
to the desired position.
NOTEz To prevent the battery from running down,
operate the switch with the engine running.Heated seats*
The heated seats can be operated with the ig-
nition switch or the operation mode in ON. Operate the switch as indicated by arrows.
The indication lamp (A) will illuminate while the heater is on.
1 (HI)Heater high (for quick heating).2Heater off.3 (LO)Heater low (to keep the seat warm).CAUT,ONz Operate in the high position for quick heat-
ing. Once the seat is warm, set the heater to low to keep it warm. Slight variations in seat
temperature may be felt while using the heated seats. This is caused by the operation
of the heater’s internal thermostat and does not indicate a malfunction.
z If the following types of persons use the
heated seats, they might become too hot or
receive minor burns (red skin, heat blisters, etc.):

Rear seat (Club cab andDouble cab)*
When a person is sitting in the middle seating position of the rear seat, adjust the head re-
straint to height at which it lock in position.
Refer to “Head restraints*” on page 4-05.Folding the seatback forward
(Double cab)
Pull up the band on the top of the seatback
and fold it forward.
To return (Double cab)
Raise the seatback until it is locked securely in place.
Push and pull the seatback lightly to be sure
it is secure.
Folding up the seat cushion
(Club cab)
The right and left seat cushions can be folded up separately.
To fold the seat cushions up, raise the seat
cushions.
Securely retain the seat cushion by hooking
the retaining band (A) onto the head restraint (B) of the rear seat.
Armrest (Double cab)
To use the armrest, fold it down.
To return to the original position, push it
backward (into the seatback) until it is level
with the seat.NOTEz Do not climb or sit on the armrest. Doing so
could damage the armrest.
z The top surface of the armrest contains a cup
holder for rear seat occupants.
Refer to “Cup holder” on page 7-104.
Rear seat (Club cab and Double cab)*
4-042.7(20(1Seat and seat belts4

Head restraints*:ARN,NGzDriving without the head restraints in
place can cause you and your passengers serious injury or death in an accident. To
reduce the risk of injury in an accident,
always make sure the head restraints are installed and properly positioned when
the seat is occupied.
z Never place a cushion or similar device on
the seatback. This can adversely affect head restraint performance by increasing
the distance between your head and the restraint.
To adjust height
Front seats
Adjust the head restraint height so that the
centre of the head restraint is as close as pos-
sible to ear level to reduce the chances of in- jury in the event of collision. Any person too
tall for the head restraint to reach their seated ear level, should adjust the restraint as highas possible.
To raise the head restraint, move it upward.
To lower the restraint, move it downward while pushing the height adjusting knob (A)
in the direction of the arrow. After adjust- ment, push the head restraint downward andmake sure that it is locked.
Rear centre seat (Double cab)
To reduce the risk of injury in an accident,pull up the head restraint to the locked posi- tion.

To raise the head restraint, move it upward.
To lower the restraint, move it downward
while pushing the height adjusting knob (A) in the direction of the arrow. After adjust- ment, push the head restraint downward and
make sure that it is locked.
Head restraints*
4-052.7(20(1Seat and seat belts4

:ARN,NGzWhen a person sits in the middle seating
position of the rear seat, pull up the head
restraint to a height at which it locks in position. Be sure to make this adjustment
before starting to drive. Serious injuries
could otherwise be suffered as the result of an impact.NOTEz The head restraint height of the outer seat in
the rear seat cannot be adjusted.
To remove
Lift the head restraint with the height adjust-
ing knob (A) pushed in.
To install
Confirm that the head restraint is facing the
correct direction, and then insert it into the
seatback while pressing the height adjusting knob (A) in the direction indicated by the ar-
row.
The head restraint stalk with the adjustment notches (B) must be installed in the hole withthe adjusting knob (A) (except head restraints
of the outer seat).
CAUT,ONz Confirm that the height adjusting knob (A)
is correctly adjusted as shown in the illustra- tion, and also lift the head restraints to en- sure that they do not come out of the seat-back.CAUT,ONz The shape and size of the head restraint dif-
fers according to the seat. Always use the
correct head restraint provided for the seat and do not install the head restraint in the
wrong direction.
Head restraints*
4-062.7(20(1Seat and seat belts4

Seat belts
To protect you and your passengers in the event of an accident, it is most important that
the seat belts are worn correctly while driv- ing.
The front seat belts each have a pretensioner system. (Club cab)
The front seat belts and the rear outer seat belts each have a pretensioner system. (Dou-
ble cab)
These belts are used the same way as a con- ventional seat belt.
Refer to “Seat belt pretensioner system and force limiter system*” on page 4-10.:ARN,NGz Seat belts should always be worn by every
adult who drives or rides in this vehicle, and by all children who are tall enough to
wear seat belts properly.
Other children should always use proper child restraint systems.
z Always place the shoulder belt over your
shoulder and across your chest. Never put
it behind you or under your arm.
z One seat belt should be used by only one
person. Doing otherwise can be danger-
ous.:ARN,NGz The seat belt will provide its wearer with
maximum protection if the recliner seat- back is placed in fully upright position.
When the seatback is reclined, there is
greater risk that the passenger will slide
under the belt, especially in a forward im- pact accident, and may be injured by the
belt or by striking the instrument panel or seatbacks.
z Remove any twists when using the belt.
z No modifications or additions should be
made by the user which will either pre-
vent the seat belt adjusting devices from operating to remove slack, or prevent theseat belt assembly from being adjusted to remove slack.
z Never hold a child in your arms or on
your lap when riding in this vehicle, even
if you are wearing your seat belt. To do so risks severe or fatal injury to the child in
a collision or sudden stop.
z Always adjust the seat belt to a snug fit.
z Always wear the lap portion of the belt
over your hips.3-point type seat belt (with
emergency locking mechanism)
This type of belt requires no length adjust-
ment. Once worn, the belt adjusts itself to the movement of the wearer, but in the event of a
sudden or strong shock, the belt automatical-
ly locks to hold the wearer’s body.
NOTEz You can check if the belt locks by pulling it
forward quickly.
To fasten
1. Pull the seat belt out slowly while hold-
ing the latch plate.
NOTEz When the seat belts cannot be pulled out in a
locked condition, pull the belts once force-
fully and then return them. After that, pull
the belts out slowly once again.
2. Insert the latch plate into the buckle until
a “click” is heard.
Seat belts
4-072.7(20(1Seat and seat belts4

:ARN,NGzNever wear the lap portion of the belt
across your abdomen. During accidents it
can press sharply against the abdomen and increase the risk of injury.
z The seat belts must not be twisted when
worn.
3. Pull the belt slightly to adjust slackness
as desired.
To unfasten
Hold the latch plate and push the button on
the buckle.
NOTEz As the belt retracts automatically, keep hold-
ing the latch plate while retracting so that the
belt stows slowly. Failure to do this could damage the vehicle.NOTEz If the seat belt (A) or ring (B) becomes dirty,
the belt may not retract smoothly. If the seat
belt and ring are dirty, clean them with a
mild soap or detergent solution.Seat belt reminder

For the driver and the front
passenger

[Colour liquid crystal display type@*-This warning lamp shows the case
of the left-hand drive vehicles.
If the ignition switch is turned to the “ON”
position or the operation mode is put in ON while the driver’s and/or the front passeng-er’s seat belt is not fastened, the warning
lamp comes on and the tone sounds for ap- proximately 6 seconds to remind the driver
and/or the front passenger to fasten the seat
belt.
If the vehicle is driven with the seat belt still
unfastened, the warning lamp will blink and
the tone will sound intermittently until the
seat belt is fastened.
:ARN,NGz Do not install any accessory or sticker
that makes the lamp difficult to see.NOTEz If the seat belt subsequently remains unfas-
tened, the warning lamp and the tone will is-
sue further warnings each time the vehicle starts moving from a stop.
z For the front passenger seat, the warning
function works only while a person is sitting
on the seat.
z When luggage is placed on the front passen-
ger seat, a sensor in the seat cushion may,
depending on the weight and position of the
luggage, cause the warning tone to sound
and the warning lamp to come on.For the rear passenger

NOTEzIf a seat belt is unfastened while the vehicle
is being driven, the tone sounds for approxi-
mately 1 second and the warning lamp comes on for approximately 30 seconds. At the same time, the warning lamp for the seat
where the seat belt is not fastened comes on.
z If the seat belts are initially fastened but a
seat belt is unfastened while the vehicle is
stationary and the vehicle is then driven with the seat belt still unfastened, the warning
lamp comes on again for approximately 30 seconds.Adjustable seat belt anchor
The seat belt anchor height can be adjusted.
To move the anchor, pull the lock knob (A) and slide the anchor to the desired position.
Release the lock knob to lock the anchor into
position.
:ARN,NGz When adjusting the seat belt anchor, set it
at a position that is sufficiently high so
that the belt will make full contact with your shoulder but will not touch your
neck.Pregnant women restraint:ARN,NGz Seat belts work for everyone, including
pregnant women. Pregnant women shoulduse the available seat belts. This will re-
duce the likelihood of injury to both the woman and the unborn child. The lap belt should be worn across the thighs and as
snug against the hips as possible, but not across the waist. Consult your doctor if
you have any additional questions or con- cerns.Seat belt pretensioner
system and force limiter system*
The front seat belts each have a pretensioner system and force limiter system. (Club cab)
The front seat belts and the rear outer seat
belts each have a pretensioner system and force limiter system. (Double cab)
Pretensioner system
When the ignition switch or the operation
mode is under the following conditions, if there is a frontal impact or a side impact (ve-
hicles equipped with SRS side airbags and SRS curtain airbags) severe enough to injure
the driver and/or front passenger or when a rollover or overturning of the vehicle is de-
tected (if so equipped), the pretensioner sys- tem will retract the respective seat belts in-
stantaneously, thus maximizing the seat belt’s
effectiveness.
[Except vehicles equipped with keyless oper-
ation system@
The ignition switch is in the “ON” or “START” position.
[Vehicles equipped with keyless operation
system@
The operation mode is in ON.
:ARN,NGz To obtain the best results from your pre-
tensioner seat belt, make sure you have adjusted your seat correctly and wear your seat belt properly.
Pregnant women restraint
4-102.7(20(1Seat and seat belts4