2020 MITSUBISHI L200 Owner's Manual (in English)

Redisplay of a warning displayscreen
When the mark is displayed, if you lightly
press the multi information display switch a
few times, the warning display screen you
switched from is redisplayed.
Other interrupt displays
The operation status of each system is dis-
played on the information screen.
Refer to the appropriate page in the warning display list for further details.
Refer to “Other interrupt displays” on page
5-45.
mark display
This is displayed when you press the multi information display switch and return from the warning display screen to the previous
screen.
This mark is also displayed if there is another
warning other than the one displayed.
When the cause of the warning display is eliminated, the
mark goes out automatical-
ly.
NOTEz When the mark is displayed, the warning
display screen can be redisplayed on the in- formation screen.
Refer to “Information screen (when the igni-
tion switch or the operation mode is OFF)” on page 5-05.
Refer to “Information screen (when the igni- tion switch or the operation mode is ON)”
on page 5-05.Engine coolant temperature
display
This indicates the engine coolant temperature.If the coolant becomes hot, “
” will blink.
Pay careful attention to the engine coolant temperature
display while you are driv-
ing.
CAUT,ONz If the engine is overheating, “” will blink.
In this case, the bar graph is in the red zone.
Immediately park the vehicle in a safe place
and take the required measures. Refer to “Engine overheating” on page 8-09.Fuel remaining display
This displays the amount of fuel remaining.
F (1) - Full
E (0) - Empty
NOTEz It may take several seconds to stabilise the
display after refilling the tank.
z If fuel is added with the ignition switch or
the operation mode is in ON, the fuel gauge may incorrectly indicate the fuel level.
z The arrow (A) indicates that the fuel tank
filler door is located on the left side of the
body.
Multi information display - Type 1
5-072.7(20(1Instruments and controls5

Fuel remaining warning dis-play
When the fuel is reduced to approximately 10
litres, the information screen switches to the interrupt display of the fuel remaining warn-
ing display, and the “
” mark (B) on the fuel
remaining display flashes slowly (approxi- mately once per second). After a few sec-
onds, the information screen returns from the fuel remaining warning display to the previ-ous screen.
If the remaining fuel level is reduced further,
the information screen switches to the fuel re-
maining warning display and the “
” mark
(B) on the fuel remaining display flashes
quickly (approximately twice per second).
CAUT,ONz Do not drive with an extremely low fuel lev-
el; running out of fuel could cause damage to the fuel system.NOTEz On inclines or curves, the display may be in-
correct due to the movement of fuel in the
tank.Outside temperature display
This shows the temperature
outside the vehicle.
NOTEz The display setting can be changed to the
preferred units (

Service reminder
Displays the approximate time until the next
periodic inspection recommended by
MITSUBISHI MOTORS . “---” is displayed
when the inspection time has arrived.
NOTEz Depending on the vehicle specifications, the
displayed time until the next periodic inspec-
tion may differ from that recommended by
MITSUBISHI MOTORS.
In addition, the display settings for the next periodic inspection time can be modified.
To modify the display settings, have it adjus- ted at a MITSUBISHI MOTORS Authorized
Service Point.
For more details, contact a MITSUBISHI
MOTORS Authorized Service Point.
1. Displays the time until the next periodic
inspection.
NOTEz The distance is shown in units of 100 km
(100 miles). The time is shown in units of months.
2. This informs you that a periodic inspec-
tion is due. Consult a MITSUBISHI
MOTORS Authorized Service Point.
At that time, when the ignition switch is turned from the “LOCK” position to the
“ON” position or the operation mode is
changed from OFF to ON, the warning display is displayed for a few seconds on
the information screen.
3. After your vehicle is inspected at a
MITSUBISHI MOTORS Authorized
Service Point, it displays the time until the next periodic inspection.
To reset
The “---” display can be reset while the igni-
tion switch or the operation mode is in OFF.When the display is reset, the time until the
next periodic inspection is displayed and the
warning display is no longer displayed when the ignition switch is turned from the
“LOCK” position to the “ON” position or the operation mode is changed from OFF to ON. 1. When you lightly press the multi infor-
mation display switch a few times, the
information display switches to the serv- ice reminder display screen.
2. Press and hold the multi information dis-
play switch for approximately 2 seconds or more to display “
” and make it
flash. (If there is no operation for ap-
proximately 10 seconds with flashing, the display returns to the previousscreen.)
Multi information display - Type 1
5-092.7(20(1Instruments and controls5

3.Lightly press the multi information dis-
play switch while the icon is flashing to
change the display from “---” to
“CLEAR”. After this, the time until the
next periodic inspection will be dis- played.CAUT,ONz The customer is responsible for making sure
that periodic inspection and maintenance are
performed.
Inspections and maintenance must be per- formed to prevent accidents and malfunc- tions.NOTEz “---”display cannot be reset when the igni-
tion switch or the operation mode is in ON.NOTEz When “---” is displayed, after a certain dis-
tance and a certain period of time, the dis-
play is reset and the time until the next peri- odic inspection is displayed.
z If you accidentally reset the display, consult
a MITSUBISHI MOTORS Authorized Serv-ice Point.System check screen
When the ignition switch is turned to the
“ON” position or the operation mode is put in ON, the system check screen is displayed forapproximately 4 seconds. If there is no fault,
information screen (when the ignition switch
or the operation mode is ON) is displayed.
If there is a fault, the screen changes to warn-
ing display.
Refer to “Warning display list” on page
5-26.
NOTEz The system check screen display varies de-
pending on the customer’s equipment.Driving range display
This displays the approximate driving range
(how many more kilometres or miles you can
drive). When the driving range falls below approximately 50 km (30 miles), “---” is dis-
played.
Refuel as soon as possible.
NOTEz The driving range is determined based on
the fuel consumption data. This may vary depending on the driving conditions and habits. Treat the distance displayed as just a
rough guideline.
z When you refuel, the driving range display
is updated.
However, if you only add a small amount of fuel, the correct value will not be displayed.
Fill with a full tank whenever possible.
z On rare occasions, the value displayed for
the driving range may change if you are
parked on an extremely steep incline. This is due to the movement of fuel in the tank and
does not indicate a malfunction.
Multi information display - Type 1
5-102.7(20(1Instruments and controls5

NOTEzThe display setting can be changed to the
preferred units (km or miles).
Refer to “Changing the function settings” on page 5-13.Average fuel consumption dis-
play
This displays the average fuel consumption
from the last reset to the present time.
The reset mode conditions for the average fuel consumption display can be switched be-
tween “Auto reset” and “Manual reset”.
Refer to “Changing the reset mode for aver-
age fuel consumption and average speed” on
page 5-14.
For information on how to change the aver- age fuel consumption display setting, refer to“Changing the function settings” on page
5-23.
NOTEz The average fuel consumption display can
be reset separately for the auto reset mode and for the manual reset mode.
z “---” is displayed when the average fuel con-
sumption cannot be measured.
z The initial (default) setting is “Auto reset
mode”.
z The average fuel consumption depends on
the driving condition (road condition, driv- ing behavior, etc.). The displayed fuel con- sumption may vary from the actual fuel con-
sumption. Treat the fuel consumption dis- played as just a rough guideline.
z The memory of the auto reset mode or man-
ual reset mode for the average fuel con-sumption display is erased if the battery isdisconnected.
z The display setting can be changed to the
preferred units { km/L, mpg (US), mpg (UK)
or L/100 km}.
Refer to “Changing the function settings” on page 5-23.Average speed display
This displays the average speed from the last
reset to the present time.
The reset mode conditions for the average speed display can be switched between “Auto
reset” and “Manual reset”.
Refer to “Changing the reset mode for aver- age fuel consumption and average speed” on
page 5-14.
For the method for changing the average
speed display setting, refer to “Changing the
function settings” on page 5-23.NOTEz The average speed display can be reset sepa-
rately for the auto reset mode and for the manual reset mode.
z “---” is displayed when the average speed
cannot be measured.
z The initial (default) setting is “Auto reset
mode”.
z The display setting can be changed to the
preferred units (km/h or mph).
Refer to “Changing the function settings” on page 5-23.
z The memory of the auto reset mode or man-
ual reset mode for the average speed displayis erased if the battery is disconnected.Momentary fuel consumption
display
While driving, this displays the momentary fuel consumption, using a bar graph.
Multi information display - Type 1
5-112.7(20(1Instruments and controls5

The “ ” mark (A) in the momentary fuel
gauge shows the average fuel consumption. When the momentary fuel consumption sur-
passes the average fuel consumption, the mo- mentary fuel consumption is displayed with a
green bar graph.
Be conscious of maintaining the momentary
fuel consumption above the average fuel con- sumption, driving with the better fuel con-
sumption can be possible.
NOTEz When the momentary fuel consumption can-
not be measured, the bar graph is not dis-
played.
z The display setting can be changed to the
preferred units { km/L, mpg (US), mpg (UK)
or L/100 km}.
Refer to “Changing the function settings” on page 5-23.
z It is possible to cancel the green bar graph.
Refer to “Changing the function settings” on page 5-23.Auto Stop Go (AS G) moni-
tor*
The accumulated time the engine has been stopped by Auto Stop & Go (AS&G) system is displayed.
Refer to “Auto Stop & Go (AS&G) system”
on page 6-25.
NOTEz When the ignition switch or the operation
mode is ON again, the accumulated time
will be reset.ECO drive assist display
This function displays how fuel-efficiently
you are driving under different driving condi-
tions.
The ECO drive assist display will change as follows if you do fuel-efficient driving using
the accelerator in a way well matched with
the vehicle speed.
NOTEz On vehicles with
A/T, the ECO drive assist
is displayed only when vehicle is driving
with the selector lever in the “D” (DRIVE)
position or when vehicle is driving in the
sport mode.ECO score display
ECO score indicates the points you have
scored on fuel-efficient driving by the num-
ber of leaves as follows:

[When the ignition switch or the operation mode is ON@
The display shows the score you achieved in the last several minutes.

[When the ignition switch is turned off or the
operation mode is put in OFF@
Multi information display - Type 1
5-122.7(20(1Instruments and controls5 ECO drive levelLow High

The display shows the overall ECO score thefunction has counted from the time when theignition switch is turned to “ON” to the time when it is turned to “LOCK” or “ACC”, or
from the time when the operation mode is set
to “ON” to the time when it is set to “OFF”.Changing the function settings
The “Display language”, “Temperature unit”,
“Fuel consumption unit”, and “Average fuel consumption and speed reset method” etc.
setting can be modified as desired. 1. Stop the vehicle in a safe place. Firmly apply the parking brake and put
the gearshift lever into the “N” (Neutral) position ( M/T) or the selector lever into
the “P” (PARK) position (A/T).
2. Lightly press the multi information dis-
play switch a few times to switch the in- formation screen to the function setting
screen.
Refer to “Information screen (when the
ignition switch or the operation mode is ON” on page 5-05.CAUT,ONz For safety, stop the vehicle before operating.
While driving, even if you operate the multiinformation display switch, the function set- ting screen is not displayed.
3. Press and hold the multi information dis-
play switch for approximately 2 seconds or more to switch from the setting mode
screen to the menu screen.
NOTEz To return the menu screen to the function
setting screen, press and hold the multi in-formation display switch for approximately 2 seconds or more.
z If no operations are made within approxi-
mately 30 seconds of the menu screen being displayed, the display returns to the function
setting screen.
4. Select the item to change on the menu
screen and change to the desired setting. Refer to the following items for further
details on the operation methods.
Refer to “Changing the reset mode for aver-
age fuel consumption and average speed” on
page 5-14.
Refer to “Changing the fuel consumption dis-
play unit” on page 5-15.
Refer to “Changing the temperature unit” on
page 5-15.
Refer to “Changing the display language” on page 5-15.
Refer to “Operation sound setting” on page
5-16.
Refer to “Changing the time until “REST REMINDER” is displayed” on page 5-16.
Refer to “Changing the turn-signal sound” on page 5-16.
Refer to “Changing the momentary fuel con- sumption display” on page 5-17.
Multi information display - Type 1
5-132.7(20(1Instruments and controls5ECO drive levelLow High

Refer to “Returning to the factory settings”on page 5-17.NOTEz If the battery is disconnected, these function
settings are reset from memory and is auto-matically to the factory settings.Changing the reset mode for
average fuel consumption and average speed
The mode conditions for the average fuel consumption and average speed display can
be switched between “Auto reset” and “Man-
ual reset”. 1. Press and hold the multi information dis-
play switch for approximately 2 seconds or more to switch from the setting mode
screen to the menu screen.
Refer to “Changing the function set-
tings” on page 5-13.
2. Lightly press the multi information dis-
play switch to select
“AVG (average fuel consumption andaverage speed setting)”.
3. Press and hold the multi information dis-
play switch for approximately 2 seconds
or more to switch from A/1 (Auto reset mode) to M/2/P (Manual reset mode), or from M/2/P to A/1.
The setting is changed to the selected mode condition.
Manual reset mode
z When the average fuel consumption and
average speed are being displayed, if
you hold down the multi information
display switch, the average fuel con-
sumption and average speed displayed at
that time are reset.
z When the following operation is per-
formed, the mode setting is automatical-
ly switched from manual to auto.
[Except for vehicles equipped with key-
less operation system@
Turn the ignition switch from the “ACC” or “LOCK” position to the “ON” posi-
tion.
[For vehicles equipped with keyless op- eration system@
Change the operation mode from ACC
or OFF to ON.

Switching to auto occurs automatically. If switching to manual mode is done,
however, the data from the last reset is displayed.
Auto reset mode
z When the average fuel consumption and
average speed are being displayed, if
you hold down the multi information
display switch, the average fuel con-
sumption and average speed displayed at
that time are reset.
z When the ignition switch or the opera-
tion mode is in the following condition, the average fuel consumption display
and average speed display are automati-
cally reset.
[Except for vehicles equipped with key-
less operation system@
The ignition switch is in the “ACC” or
“LOCK” position for approximately 4 hours or longer.
[For vehicles equipped with keyless op- eration system@
The operation mode is in ACC or OFF
for approximately 4 hours or longer.
NOTEz The average fuel consumption display and
average speed display can be reset separately
for the auto reset mode and for the manual reset mode.
z The memory of the auto reset mode or man-
ual reset mode for the average fuel con- sumption display and average speed display
is erased if the battery is disconnected.
Multi information display - Type 1
5-142.7(20(1Instruments and controls5