2010 ASTON MARTIN V8 VANTAGE Workshop Manual

Wiring and Circuit Protection (18.01)
Electric Distribution/E lectronic Control (18.00)
18-1-16 Workshop Manual May 2007
15. Remove lower cover RH (screw x1) (see Fig. 6).
16. Cut cable ties securing pipes and wires to cylinder (see
Fig. 7).
17. Release clips securing hall e ffect sensors to cylinder and
disconnect sensors. 18. Remove cable ties securing
pipes/harness to roof frame
(see Fig. 8).
19. Remove screws securing P- clips and strap to frame and
release harness.
20. Remove screw of pipe/harness keeper plate, loosen other and release pipe.
21. Attach string to cylinder end of harness to aid installation.
22. Feed harness through to tonneau area by carefully guiding through roof mechanism and release string (see
Fig. 9).
23. Disconnect heated rear windscreen multiplug.

Fig. 6

Fig. 7

Fig. 8

Fig. 9

Wiring and Circuit Protection (18.01)
Electric Distribution/Electronic Control (18.00)
May 2007 Workshop Manual 18-1-17
24. Disconnect multiplugs (x2) and feed into tonneau area (LH) (see Fig. 10).
25. Disconnect multiplug (RH).
26. Release multiplug from body and disconnect and feed through into tonneau area (RH) (see Fig. 11). 27. Remove harness/pipe retaining clips (x2) (LH) (see Fig.
12).
28. Remove harness/pipe retain ing clips (x9) behind Roll
Over Protection System (ROPS) units (see Fig. 13).

Fig. 10

Fig. 11
Fig. 12

Fig. 13

Wiring and Circuit Protection (18.01)
Electric Distribution/E lectronic Control (18.00)
18-1-18 Workshop Manual May 2007
29. Remove harness/pipe retaining clips (x3) LH side (see
Fig. 14).
30. Cut cable tie securing valve to bracket (see Fig. 15).
31. Release valve from support bracket, the bracket may need bending slightly. 32. Disconnect multip
lug (see Fig. 16).
33. Cut cable ties securing pipe s to cylinder.
34. Release clips securing hall effect sensors to cylinder, disconnect sensors and remove cylinder (see Fig. 17).

Fig. 14

Fig. 15
Fig. 16

Fig. 17

Wiring and Circuit Protection (18.01)
Electric Distribution/Electronic Control (18.00)
May 2007 Workshop Manual 18-1-19
35. Remove trim clip and releas e tonneau lining stiffening
rod (see Fig. 18).
36. Release velcro and move tonneau well liner aside to expose lower cylinder fixing and motor casing.
37. Release cylinder lower retaining clip and disconnect cylinder from body (see Fig. 19).
38. Remove cylinder pivot bracket from body (bolts x3). 39. Release pump and casing from under tonneau body side
(see Fig. 20).
40. Release velcro around pump casing and remove casing (see Fig. 21).

Fig. 18

Fig. 19

Fig. 20

Fig. 21

Wiring and Circuit Protection (18.01)
Electric Distribution/E lectronic Control (18.00)
18-1-20 Workshop Manual May 2007
41. Remove harness/pipe cable ties (see Fig. 22).
42. Disconnect pump multiplug (see Fig. 23).43. Disconnect pump mult
iplug (see Fig. 24).
44. Remove pump relays.
45. Remove end cover (locating tabs x2).
46. Disconnect pump lucar conne ctors (x2) (see Fig. 25).
47. Remove harness from vehicle.
Installation
1. Install harness to approximate route on vehicle.
2. Connect pump lucar connectors.
3. Install pump end cover.
4. Connect pump multiplugs (x2).
5. Install pump relays (x2).
6. Install pump casing and secure velcro.
7. Install harness/pipe cable ties.
8. Install motor and casing under tonneau onto location posts.
9. Install cylinder pivot bracket and connect cylinder to bracket.

Fig. 22

Fig. 23
Fig. 24

Fig. 25

Wiring and Circuit Protection (18.01)
Electric Distribution/Electronic Control (18.00)
May 2007 Workshop Manual 18-1-21
10. Move tonneau well liner ar ound lower cylinder fixing
and motor casing and secure velcro
11. Install trim clip and positi on tonneau lining stiffening
rod.
12. Install Hall sensors and secure with clips.
13. Secure pipes/wires to cylinder with cable ties.
14. Connect multiplug.
15. Install valve to support bracket, reposition bracket.
16. Install cable tie securing valve to bracket. Ensure no pipes or wiring will foul roof mechanism.
17. Install harness/pipe retaining clips (x9) behind ROPS units.
18. Install harness/pipe re taining clips LH (x2).
19. Install harness/pipe re taining clips RH (x3).
20. Feed harness into passenger compartment and connect multiplugs (LH).
21. Feed harness into passenger compartment, connect multiplugs and secure to body (RH).
22. Connect multiplug (RH).
23. Connect HRW multiplug.
24. Attach pipes to guide string, feed harness through roof frame and remove string.
25. Position Hall sensors to cyli nder and secure with clips.
26. Secure pipes and wires to cylinder with cable ties
27. Install p-clips and strap to harness and secure to frame with screws.
28. Install harness under keeper plate, install and tighten screws
29. Install new clips securi ng pipes to roof frame.
30. Install lower cover.
31. Attach pipes to guide string, feed harness through roof frame and remove string.
32. Position Hall sensors to cyli nder and secure with clips.
33. Secure pipes and wires to cylinder with cable tie.
34. Install new clips securi ng pipes to roof frame.
35. Attach pipes to guide string, feed harness through roof frame and remove string.
36. Position Hall sensors to cyli nder and secure with clips.
37. Secure pipes and wires to cylinder with cable tie.
38. Install new clips securi ng pipes to roof frame.
39. Connect battery.
40. Install Quarter trim LH (see Workshop Manual procedure 01.05.CS Panel Assembly - Quarter Trim
Lower - LH - Renew).
41. Install Quarter trim RH (see Workshop Manual procedure 01.05.CR Panel Assembly - Quarter Trim
Lower - RH - Renew).
42. Restore roof and tonneau to original positionTransaxle Harness-Renew
Removal
1. Remove RH Wheel arch liner (see Workshop Manual procedure 01.02.HB Wheel Arch Liner - Rear - RH -
Renew).
2. Remove rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
3. Disconnect transaxle multiplug from body harness.
4. Release harness from RH wheel arch (clips x2).
5. Disconnect LH and RH pad wear sensor multiplug (X2).
6. Disconnect load le vel sensor multiplug.
7. Disconnect LH and RH AB S sensor multiplugs (x2)
8. Disconnect reverse light switch and release harness from transaxle (clips x2).
9. Release harness clips (x23) from subframe and toe control arms.
Installation
1. Secure harness clips (x23) to subframe and toe control arms.
2. Connect reverse light swit ch multiplug and secure
harness clips (x2) to transaxle.
3. Connect ABS sensors
4. Connect load level sensor.
5. Connect pad wear sensor multiplugs.
6. Connect transaxle multiplug and secure harness to wheel arch.
7. Install rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
8. Install RH rear wheel arch liner (see Workshop Manual procedure 01.02.HB Wheel Arch Liner - Rear - RH -
Renew).
Repair Operation Time (ROT)
Warning
To prevent damage to electrical components, always disconnect the vehicle battery when working on the
vehicle's electrical system. The earth lead (- ve) must be disconnected first an d reconnected last.
Warning
Always connect the battery earth (- ve) terminal last.

Wiring and Circuit Protection (18.01)
Electric Distribution/E lectronic Control (18.00)
18-1-22 Workshop Manual May 2007
Engine Wiring Harness-Renew
Removal
1. Remove engine (see Workshop Manual procedure
03.00.AC Engine Assembly - Remove for access and
refit).
2. Disconnect vacuum pipe and multiplug from EGR module (see Fig. 1).
3. Loosen and disconnect EGR pipe union (see Fig. 2). 4. Remove bolts (x2) securing EGR module to inlet
manifold, remove EGR valve, remove and discard gasket
(see Fig. 3).
5. Install engine lifting brackets, (303-749) to front of engine and (303-536) to rear of engine.
6. Connect suitable slings to engine lifting brackets.
7. Connect hoist to slings, raise hoist to take weight of engine.
8. Remove nuts (x2) securi ng engine hydramounts to
subframe.
9. Raise hoist and remove engine from subframe.
10. Lower engine onto work be nch, disconnect hoist from
slings, move hoist aside.
11. Remove nuts (X8), LH exhaust manifold to cylinder head, remove manifold (see Fig. 4).
Repair Operation Time (ROT)
Warning
To prevent damage to electrical components, always disconnect the vehicle battery when working on the
vehicle's electrical system. Th e earth lead (- ve) must be
disconnected first and reconnected last.

Fig. 1
Fig. 2
$
$%
Fig. 3
Fig. 4
$$
%$

Wiring and Circuit Protection (18.01)
Electric Distribution/Electronic Control (18.00)
May 2007 Workshop Manual 18-1-23
12. Remove nuts (x8) securing RH exhaust manifold to cylinder head, remove ma nifold (see Fig. 5).
13. Remove coil covers (x2).
14. Disconnect multiplugs (x8) to ignition coils (see Fig. 6).
15. Disconnect multiplug to VVT solenoids (x2).
16. Disconnect multiplugs (x8) to Injectors (see Fig. 7).17. Disconnect multiplug (x1) fu
el rail pressure sensor (see
Fig. 8).
18. Remove bolt (x1) purge valve pipe to RH support bracket.
19. Release engine harness from RH support bracket (clips x3).
20. Remove cam cover nut (x1) and bolts (x2) and remove RH support bracket.
21. Release heater hose from heater hose bracket.
22. Release vacuum pipe from heater hose bracket clips (x2).
23. Release harness from heater hose bracket clips (x3).
24. Remove cam covers nuts (x2) and release RH heater hose bracket.
25. Disconnect multiplug (x1) alternator (see Fig. 9).
Fig. 5
Fig. 6
Fig. 7
$
$
$
Fig. 8
Fig. 9
$
$