2010 ASTON MARTIN V8 VANTAGE Workshop Manual

Front Suspension (04.01)
Suspension (04.00)
November 2008 Workshop Manual 4-1-7
8. Install caliper and Allen bolts (x2) and tighten.
9. Install ABS speed sensor, install and torque tighten.
10. Install sensor multiplug.
11. Install pad wear sensors.
12. Install track rod end to vertical link, install and torque tighten nut.
13. Install road wheel(s).
14. Pump brake pedal.
15. Lower vehicle on ramp.
16. 4 wheel alignment - check/adjust (see Workshop Manual procedure 04.00.AD 4 Wheel Alignment -
Check & Adjust).
Front Suspension Sensor Assembly-
Renew
Removal
1. Raise vehicle on ramp
2. Remove nut/bolt securing ride height sensor link to
lower suspension arm (see Figure 1).
3. Remove nut/Torx bolt, ride height sensor to subframe.
4. Disconnect ride heig ht sensor multiplug.
5. Remove bolts (x2) securing sensor to sensor bracket.
Installation
1. Align sensor to bracket and install bolts (x2).
2. Connect ride height sensor multiplug.
3. Position sensor to subframe, install and torque tighten nut/Torx bolt.
4. Align sensor link to lower suspension arm, install and torque tighten nut/bolt.
5. Lower vehicle on ramp.
Repair Operation Time (ROT)

Front Suspension (04.01)
Suspension (04.00)4-1-8 Workshop Manual November 2008

Rear Suspension (04.02)
Suspension (04.00)
May 2007 Workshop Manual 4-2-1
Suspension (04.00)
Rear Suspension (04.02)
Description
Anti-roll Bar
An anti-roll bar, mounted on the rear subframe connects to
the LH and RH lower suspension arms via drop links. The
drop links, with a ball joint at either end, transmit vertical
movement of the rear suspension to the anti-roll bar,
minimising body roll.
Vertical Link
The vertical link carries the hub, the cartridge wheel bearing,
the ABS rotor, the wheel speed sensor, the brake caliper, the
hand brake caliper and the brake disc and shield.
A toe control (track-rod) arm secures the rear of the vertical
link to the subframe. The toe control arm is adjustable, on
an eccentric cam, to alter the rear road wheel toe alignment.
04-02-001
Upper Wishbone
Rear Hub Assy
Rear Subframe Lower WishboneAnti Roll Bar LinkAnti Roll Bar
Track Control Arm
Track Control Arm

Rear Suspension (04.02)
Suspension (04.00)4-2-2 Workshop Manual May 2007
Specifications
Maintenance
RH/LH Rear Hub and Bearing Assembly-
Renew
Removal
1. Raise vehicle on ramp.
2. Remove road wheel(s).
3. Remove RH/LH rear drivesha ft (see Workshop Manual
procedure 05.05.BB/05.05.AB Drive Shaft Assembly -
RH/LH - Renew).
4. Ease caliper pistons to release pads.
5. Remove caliper Allen bolts (x2) release caliper and tie aside.
6. Remove handbrake caliper bolts (x2) and tie caliper aside. 7. Remove brake disc Torx screws (x2), remove disc.
8. Disconnect multiplug fr
om wheel speed sensor.
9. Remove Torx securing wheel speed sensor to vertical link, remove sensor.
10. Remove Allen bolts (x4) se curing hub bearing assembly
in vertical link.
11. Release/remove hub bearing a ssembly from vertical link.
Installation
1. Clean vertical link and mating face on hub bearing
carrier.
2. Install hub bearing assembly. Install and torque tighten Allen bolts (x4).
3. Clean wheel speed sensor.
4. Install wheel speed sensor, install and torque tighten Torx screw.
5. Connect multiplug to wheel sped sensor.
6. Clean disc.
7. Install disc, install and torq ue tighten Torx screws (x2).
8. Install caliper, install and torque tighten Allen bolts (x2).
9. Install handbrake caliper, install and torque tighten
retaining bolts (x2).
10. Install RH/LH driveshaft (see Workshop Manual
procedure 05.05.BB/05.05.AB Drive Shaft Assembly -
RH/LH - Renew).
11. Pump brake pedal.
12. Install road wheel(s).
13. Lower vehicle on ramp.
RH/LH Rear Lower Arm Assembly-Renew
Removal
1. Raise vehicle on ramp.
2. Remove road wheel(s).
3. Remove nut, anti-roll bar li nk to lower suspension arm.
Release link.
4. Remove bolt securing damper to lower suspension arm.
5. Remove bolt and nut/bolt, securing lower suspension arm to subframe.
6. Remove nut/bolt securing lower suspension arm to
vertical link.
7. Release/remove lower suspension arm from subframe and vertical link.
Installation
1. Clean lower suspension arm and mating faces on vertical link, subframe, damper and anti-roll bar link.
2. Install lower suspension ar m to subframe and vertical
link.
Torque Figures
DescriptionNmlb. / ft.
Brake Dust Shield. 9 7
Bearing Assembly to the Vertical
link. 50 37
Halfshaft Nut 300 221.5
Spring and Damper Bracket
Mounting 75-80 55.5-59.5
Spring and Damper Top
Mounting to Bracket 22.5 17
Spring and Damper Lower
Mounting 175 129.5
Track rod Arm to Vertical Link 115 85
Anti-roll Bar Link 110 81.5
Anti-roll Bar Mounting Bolts
Torque bolt 1, then bolt 2, then
bolt 1 again (to allow for rubber
compression) 22.5 17
Ride Height Sensor M8 22.5 17
Torque the following suspensi on fixings with the vehicle
at normal ride height
Vertical Link to the Lower
Suspension Arm. 175 129.5
Vertical Link to the Upper
Suspension Arm. 115 85
Lower Suspension Arm to the
Subframe. 115 85
Upper Suspension Arm to the
Subframe 115 85
Track-Rod Arm to Subframe 115 85
Normal ride height: 2 x 37.5kg in front seats (37.5kg in
each seat) plus a full fuel tank.
Repair Operation Time (ROT)
Repair Operation Time (ROT)
ItemCode
Rear Lower Arm Assembly-Renew RH04.02.AC
Rear Lower Arm Assembly-Renew LH04.02.AD

Rear Suspension (04.02)
Suspension (04.00)
May 2007 Workshop Manual 4-2-3
3. Install bolt and bolts/nuts (x2), lower suspension arm to subframe and vertical link. Do not torque tighten at this
stage.
4. Align damper to lower suspension arm, install bolt. Do not torque tighten at this stage.
5. Align anti-roll bar link to lower suspension arm, install
nut. Do not torque tighten at this stage.
6. Install road wheel(s).
7. Lower vehicle on ramp.
8. Torque tighten suspension nuts/bolts.
9. 4 wheel alignment - check/adjust (see Workshop Manual procedure 04.00.AD 4 Wheel Alignment -
Check and Adjust).
RH/LH Upper Rear Arm Assembly-Renew
Removal
1. Raise vehicle on ramp.
2. Remove road wheel(s).
3. Remove nuts/bolts (x2), upper suspension arm to subframe.
4. Remove nut/bolt securing upper suspension arm to vertical link.
5. Release and remove upper suspension arm assembly.
Installation
1. Clean upper suspension arm and mating faces on subframe and vertical link.
2. Install upper suspension arm in subframe.
3. Install bolts/nuts (x2), upper suspension arm to subframe. Do not torque tighten at this stage.
4. Install upper suspension arm in vertical link, install bolt/
nut. Do not torque tighten at this stage.
5. Install road wheel(s).
6. Lower vehicle on ramp.
7. Torque tighten nuts/bolts, upper suspension arm to vertical link and subframe.
RH/LH Toe Control Rear Arm Assembly-
Renew
Removal
1. Raise vehicle on ramp.
2. Remove road wheel(s).
3. Release ABS sensor harness clips (x2) from toe control arm.
4. Remove nut/bolt securing toe control arm to subframe.
5. Remove nut/bolt securing toe control arm to vertical link.
6. Release/remove toe control arm.
Installation
1. Clean toe control arm and mating faces on vertical link and subframe.
2. Install toe control arm in vertical link and subframe.
3. Install bolts/nuts (x2). toe control arm to vertical link and subframe. Do not torque tighten at this stage.
4. Install ABS sensor harness clips in toe control arm.
5. Install road wheel(s).
6. Lower vehicle on ramp.
7. 4 wheel alignment - check/adjust(see Workshop Manual procedure 04.00.AD 4 Whee l Alignment - Check and
Adjust).
Rear Anti-Roll Bar-Renew
Removal
1. Raise vehicle on ramp.
2. Remove rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
3. Remove nuts (x2), anti-roll bar links to lower arms.
4. Remove bolts (x4), bush straps (x2), anti-roll bar to subframe.
5. Remove anti-roll bar. Note cut-off section at top.
6. Remove bushes (x2) from anti-roll bar.
7. Remove nuts (x2), washers (x2), remove links from anti- roll bar.
Caution
Final tightening of suspension components must be
carried out with the suspensi on arms at normal ride
height. Failure to do this wi ll over stress the suspension
bushes when the suspension is deflected to maximum upward travel.
Repair Operation Time (ROT)
Repair Operation Time (ROT)
Repair Operation Time (ROT)

Rear Suspension (04.02)
Suspension (04.00)4-2-4 Workshop Manual May 2007
Installation
1. Clean anti-roll bar, bushes, bush straps and links.
2. Install links (x2), to anti-roll bar. Install washers (x2) and nuts (x2). Do not torque tighten.
3. Install bushes (x2) on anti-roll bar.
4. Position anti-roll bar, align bushes (x2), install straps (x2), install bolts (x4). Do not torque tighten.
5. Position anti-roll bar drop links to lower arms, install
nuts (x2). Do not torque tighten.
6. Install rear undertray (see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
7. Lower vehicle on ramp.
8. Torque tighten link nuts (x4).
9. Torque tighten bush strap bolts (x4).
Rear Pair-Anti-Roll Bar Bushing-Renew
Removal
1. Raise vehicle on ramp.
2. Remove rear undertray(see Workshop Manual procedure01.02.PB Undertray - Rear - Renew).
3. Remove bolts (x4) securing anti-roll bar bush straps (x2) to subframe.
4. Release/remove bush straps.
5. Remove bushes (x2) from anti-roll bar.
Installation
1. Clean anti-roll bar and bush straps.
2. Install bushes onto anti-roll bar.
3. Install bush straps (x2), install bolts (x4). Do not torque tighten at this stage.
4. Install rear undertray(see Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
5. Lower vehicle on ramp.
6. Torque tighten all suspension nuts/bolts.
RH/LH Rear Anti-Roll Bar Link-Renew
Removal
1. Raise vehicle on ramp.
1. Remove nut, collect wash er, link to anti-roll bar.
1. Remove nut, link to lower suspension arm. Remove link.
Installation
1. Clean link and mating faces on anti-roll bar and lower suspension arm.
2. Install link to anti-roll bar, install washer and nut. Do not
torque tighten at this stage.
3. Position link to lower suspension arm, install nut). Do not torque tighten at this stage.
4. Lower vehicle on ramp.
5. Torque tighten link nuts (x2).
RH/LH Rear Hub Vertical Link-Renew
Removal
1. Raise vehicle on ramp.
2. Remove road wheel/s
3. With assistance, remove rear hub nut.
4. Remove nut/bolt, securing toe rod to vertical link, release toe rod.
5. Disconnect ABS sensor multiplug.
6. Remove Torx screw securing ABS sensor, remove sensor
7. Ease caliper pistons to release pads.
8. Remove caliper Allen bolts (x2) release caliper and tie aside.
9. Remove handbrake caliper bolts (x2) and tie caliper aside.
10. Remove brake disc Torx screws (x2) remove disc.
11. Remove nut/bolt securing lower suspension arm to
vertical link.
12. Remove nut/bolt securing vertical link to upper
suspension arm.
13. Release vertical link from driveshaft, remove vertical
link.
Caution
Final tightening of suspen sion components must be
carried out with the suspension arms at normal ride
height. Failure to do this will over stress the suspension bushes when the suspension is deflected to maximum
upward travel.
Repair Operation Time (ROT)
Repair Operation Time (ROT)
ItemCode
Rear Anti-Roll Bar Link-Renew RH04.02.BD
Rear Anti-Roll Bar Link-Renew LH04.02.BE
Caution
Final tightening of suspen sion components must be
carried out with the suspension arms at normal ride
height. Failure to do this wi ll over stress the suspension
bushes when the suspension is deflected to maximum
upward travel.
Repair Operation Time (ROT)
ItemCode
Rear Hub Vertic al Link-Renew RH04.02.HB
Rear Hub Vertic al Link-Renew LH04.02.GB

Rear Suspension (04.02)
Suspension (04.00)
May 2007 Workshop Manual 4-2-5
14. Tie driveshaft aside.
15. Remove Allen bolts (x4) securing hub bearing assembly in vertical link.
16. Release/remove hub bearing assembly from vertical link.
17. Remove Torx screws (x4) secu ring disc shield to vertical
link.
Installation
1. Clean vertical link, disc sh ield and hub bearing carrier.
2. Install disc shield to vert ical link, install and torque
tighten Torx screws (x4).
3. Install hub bearing assembly in vertical link. Install and tighten Allen bolts.
4. Release driveshaft.
5. Align to driveshaft, install vertical link to upper suspension arm. Install bolt/nut. Do not torque tighten at
this stage.
6. Align vertical link to lower suspension arm. Install bolt/ nut. Do not torque tighten at this stage.
7. Install hub nut. Do not torque tighten at this stage.
8. Clean brake disc.
9. Install disc and Torx screws (x2) and tighten Torx screws.
10. Install caliper and Allen bolts (x2) and tighten to.
11. Install handbrake caliper and retaining bolts (x2), tighten bolts.
12. Install ABS speed sensor, install and torque tighten Torx screw.
13. Install ABS sensor multiplug.
14. Install toe rod to vertical link, install bolt/nut. Do not torque tighten at this stage.
15. Install road wheel/s
16. Pump brake pedal.
17. Lower vehicle on ramp.
18. With assistance, torque tighten rear hub nut.
19. Correctly torque tighten all suspension nuts/bolts.
20. 4 wheel alignment - check/ adjust(see Workshop Manual
procedure 04.00.AD 4 Wheel Alignment - Check and
Adjust)
Repair Operation Time (ROT)

Rear Suspension (04.02)
Suspension (04.00)4-2-6 Workshop Manual May 2007