2010 ASTON MARTIN V8 VANTAGE Workshop Manual

Instrument Panel (IP) (01.12)
Body System (01.00)
Issue 5, January 2010 Workshop Manual 1-9-25
5. Push the gearknob down and turn it clockwise.
C-01-12-DA-15
6. Install and tighten the two screws that attach the centre console panel to the body.
C-01-12-DA-13
7. Install but do not tighten, the two Torx screws, washers and bracket to the armrest.
E-01-12-DA-08
8. Move the stowage box and install the armrest.
C-01-12-DA-40
9. Tighten the two Torx scrws th at attach the armrest to the
bracket.
C-01-12-DA-06
10. Install and tighten the two Torx screws that attach the armrest to the body.
C-01-12-DA-08

Instrument Panel (IP) (01.12)
Body System (01.00)1-9-26 Workshop Manual Issue 5, January 2010
11. Install the leather insert.
C-01-12-DA-07
12. Install the rubber mat into the cupholder.
C-01-12-DA-05
13. Install and tighten the two screws that attach the stowage compartment to the body.
C-01-12-DA-39
14. Install and tighten the four Torx screws that attach the stowage compartment to the body.
C-01-12-DA-38
15. Install and tighten the screw that attaches the stowage compartment to the body.
C-01-12-DA-37
16. Install the stowage compartment cover.
C-01-12-DA-36

Instrument Panel (IP) (01.12)
Body System (01.00)
Issue 5, January 2010 Workshop Manual 1-9-27
17. Install and tighten the four Torx screws and the four nuts that attach the stowage compartment cover to the body.
C-01-12-DA-35
18. Install the right side cover panel for the centre console.
C-01-12-DA-34
19. Install and tighten the two nuts that attach the right side cover panel for the centre console to the body.
C-01-12-DA-33
20. Install and tighten the two screws that attach the right side cover panel for the centre console to the body.
C-01-12-DA-32
21. Install the right side rear bulkhead cover.
C-01-12-DA-31
22. Install and tighten the screw that attaches the right side rear bulkhead cover to the body.
C-01-12-DA-30

Instrument Panel (IP) (01.12)
Body System (01.00)1-9-28 Workshop Manual Issue 5, January 2010
23. Install the right hand side infill panel.
C-01-12-DA-29
24. Install the left side cover panel for the centre console.
C-01-12-DA-28
25. Install and tighten the two nuts that attach the left side
cover panel for the centre console to the body.
C-01-12-DA-27
26. Install and tighten the two sc rews that attach the left side
cover panel for the centre console to the body.
C-01-12-DA-26
27. Install the stowage box cover and the rubber mat.
C-01-12-DA-25
28. Install the left side rear bulkhead cover.
C-01-12-DA-23

Instrument Panel (IP) (01.12)
Body System (01.00)
Issue 5, January 2010 Workshop Manual 1-9-29
29. Install and tighten the screw that attaches the left side rear bulkhead cover to the body.
C-01-12-DA-22
30. Install the left side infill panel.
C-01-12-DA-24
31. Remove the special tool from the operating ram on the tonneau cover.
C-01-12-DA-21
32. Fully close the tonneau cover.
33. Connect the battery.
34. Operate the front seats to their initial positions.
RH/LH Lower Quarter Panel Assembly -
Renew (Roadster Only)
Removal
1. Remove wind deflector (see Workshop Manual procedure 01.17.DA Wind Deflector - Renew).
2. Remove panel centre (see Workshop Manual procedure 01.05.FR/01.05.FS Panel Assembly - Centre - Rear
Bulkhead - LH/RH - Renew).
3. Remove speaker grille (see Workshop Manual procedure 01.05.CP/01.05.CN Grille - Speaker Rear
Quarter - LH/RH - Renew).
4. Remove screw (x1) securing quarter trim to body (under
speaker grille) (see Figure 1).
Repair Operation Time (ROT)

Instrument Panel (IP) (01.12)
Body System (01.00)1-9-30 Workshop Manual Issue 5, January 2010
5. Remove screw (x1) securing bottom centre of quarter
trim (see Figure 2).
6. Remove bolt securing body side trim to quarter panel via B-post roof aperture (see Figure 3). 7. Remove nuts (x2) securing panel quarter trim to body
side trim (see Figure 4).
8. Release fir tree clip securi ng quarter trim to body (see
Figure 5).
Figure 2
Figure 3
Figure 4
Figure 5

Instrument Panel (IP) (01.12)
Body System (01.00)
Issue 5, January 2010 Workshop Manual 1-9-31
9. Release quarter trim from heal board and remove quarter trim (see Figure6).
10. Remove nut (x2) securing lower panel to quarter panel.
Installation
1. Install nut (x2) securing lower panel to quarter panel.
2. Install quarter trim and secure under heal board.
3. Install fir tree clip securing quarter trim to body.
4. Install nuts (x2) securing panel quarter trim to body side
trim.
5. Install bolt securing body si de trim to quarter panel via
B-post roof aperture.
6. Install screw (x1) securing bottom centre of quarter trim.
7. Install screw (x1) securing quarter trim to body (under
speaker grille)
8. Remove speaker grille (see Workshop Manual procedure 01.05.CP/01.05. CN Grille - Speaker Rear
Quarter - LH/RH - Renew).
9. Remove panel centre (see Workshop Manual procedure
01.05.FR/01.05.FS Panel A ssembly - Centre - Rear
Bulkhead - LH/RH - Renew).
10. Install wind deflector (see Workshop Manual procedure 01.17.DA Wind Deflector - Renew). Figure 6

Instrument Panel (IP) (01.12)
Body System (01.00)1-9-32 Workshop Manual Issue 5, January 2010