2005 MITSUBISHI 380 Workshop Manual

REAR SEAT ASSEMBLY
INTERIOR52A-56
>>B<< INSTALLATION OF REAR SEAT CUSHION
ASSEMBLY
1. Fit the rear seat cushion into the bracket securely.
2. Fit the rear seat cushion into the rear seat hook securely.

REAR SEAT ASSEMBLY
INTERIOR52A-57
DISASSEMBLY AND REASSEMBLYM1522002000357
DISASSEMBLY STEPS
2. SEAT CUSHION COVER
3. SEAT CUSHION PAD
4. ARMREST
5. BUSH6. ARMREST PAD
8. SEATBACK COVER
9. SEATBACK PADDISASSEMBLY STEPS

FRONT SEAT BELT
INTERIOR52A-58
FRONT SEAT BELT
REMOVAL AND INSTALLATIONM1523001300370
SRS: Before removing and installing the seat belts with pre-tensioner, refer to GROUP 52B, Seat
Belt with Pre-tensioner P.52B-250.
NOTE:
*If so equipped
Pre-removal and Post-installation Operation
Turn the ignition key to the LOCK (OFF) position.
Disconnect the negative battery terminal.Post-installation Operation
Adjustment Procedures of Special Function (refer to GROUP
52B, On-Vehicle Service P.52B-250.)
1. EXTENDER SEAT BELT
ASSEMBLY*
OUTER SEAT BELT REMOVAL
STEPS
2. SASH GUIDE COVER
CENTER PILLAR TRIM LOWER
(REFER TO P.52A-11.)
3. OUTER SEAT BELT (REFER TO
GROUP 52B, SEAT BELTS WITH
PRE-TENSIONER P.52B-250.)4. CENTER PILLAR TRIM UPPER
(REFER TO P.52A-11.)
5. ADJUSTABLE SEAT BELT ANCOR
INNER SEAT BELT
6. SEAT BELT SWITCH
CONNECTOR
SHIELD COVER (REFER TO
P.52A-33.)
7. INNER SEAT BELTOUTER SEAT BELT REMOVAL
STEPS (Continued)

REAR SEAT BELT
INTERIOR52A-59
INSPECTIONM1523004400116.
SEAT BELT SWITCH CONTINUITY CHECK
REAR SEAT BELT
REMOVAL AND INSTALLATIONM1523001600371
ITEM TESTER
CONNECTIONSPECIFIED
CONDITION
Fastened seat belt 1
2 Open circuit
Unfastened seat belt 1
2 Less than 2 ohms
REMOVAL STEPS
REAR SEAT CUSHION
ASSEMBLY (REFER TO
P.52A-55.)
1. INNER SEAT BELT
2. CENTER SEAT BELT INNERREAR SHELF TRIM (REFER TO
P.52A-11.)
3. OUTER SEAT BELT
4. CENTER SEAT BELT OUTERREMOVAL STEPS (Continued)

SPECIFICATIONS
INTERIOR52A-60
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONSM1521004100227
ITEM SPECIFICATION
FRONT SEAT
Front seatback assembly bolt 44
10 Nm (33 7 ft-lb)
Front seat cushion assembly bolt 12
2 Nm (102 22 in-lb)
Front seat bolt 44
10 Nm (33 7 ft-lb)
Front seat nut 30
5 Nm (22 4 ft-lb)
REAR SEAT
Seatback assembly bolt 22
4 Nm (16 3 ft-lb)
FRONT SEAT BELT
Adjustable seat belt anchor bolt 44
10 Nm (33 7 ft-lb)
Inner seat belt bolt 44
10 Nm (33 7 ft-lb)
Outer seat belt bolt 44
10 Nm (33 7 ft-lb)
REAR SEAT BELT
Center seat belt outer and inner seat belt bolt 44
10 Nm (33 7 ft-lb)
Inner seat belt bolt 44
10 Nm (33 7 ft-lb)
Seat belt shoulder anchor bolt 44
10 Nm (33 7 ft-lb)
Seat belt lower anchor bolt 44
10 Nm (33 7 ft-lb)

80-1
GROUP 80
CONFIGURATION
DIAGRAMS
CONTENTS
OVERALL CONFIGURATION
DIAGRAM. . . . . . . . . . . . . . . . . . . . . .80-2
HOW TO READ CONFIGURATION
DIAGRAMS . . . . . . . . . . . . . . . . . . . .80-3
ENGINE COMPARTMENT. . . . . . . . .80-4ENGINE AND TRANSMISSION . . . . .80-6
DASH PANEL . . . . . . . . . . . . . . . . . . .80-10
FLOOR, SEAT AND ROOF . . . . . . . .80-17
DOOR . . . . . . . . . . . . . . . . . . . . . . . . .80-23
LUGGAGE COMPARTMENT . . . . . . .80-24

OVERALL CONFIGURATION DIAGRAM
CONFIGURATION DIAGRAMS80-2
OVERALL CONFIGURATION DIAGRAMM1801000100558
NOTE: .
1. This illustration shows only major wiring harnesses.
2. *: also equipped at the right side.

HOW TO READ CONFIGURATION DIAGRAMS
CONFIGURATION DIAGRAMS80-3
HOW TO READ CONFIGURATION DIAGRAMSM1801000200555
The wiring harness diagrams clearly show the connector locations and harness configurations on actual vehi-
cles. Some variations are included in one configuration diagram. Accordingly, some diagrams may not be
applicable for individual vehicles.