Page 977 of 1378

Flush and Fill Engine Coolant, if not done in last 36 months
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Automatic Transmission .......................... Dexron-IIE ATF
Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid
Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil (
1)
Gasoline Engine
Temperature Range
Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD
Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD
Drive Axles ................................ SAE 75W-90 API GL-5
Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5
Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5
Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid
Manual Transmission ........................ SAE 75W-90 API GL-5
Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB
Door & Hood Hinges ............................ Light Engine Oil
Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP
Power Steering Pump ....................... Power Steering Fluid
Transfer Case ................................... Dexron-IIE ATF
Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease
Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease
Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB
Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP
Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB
Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB
Weatherstrip .......................... Silicone Spray Lubricant
Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)
(
1) - SAE 10W-30 SH/CD is preferred.
(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive when changing fluid.
(
3) - For vehicles operating under heavy-duty towing conditions,
use SAE 75W-140 Synthetic lube.
NOTE: Before using SAE 75W-140 Synthetic the old fluid must
be DRAINED and FLUSHED with clean mineral based axle
lubricant. Then refill with new synthetic lube.
(
4) - Use low pressure grease gun to prevent seal damage.
(
5) - Fill until lubricant squeezes out from the base of seals.
(
6) - Fill ball joint until seal starts to swell.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application ( 1) Quantity
Automatic Transmission
1984-86 (904 HD)
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.0 Qts. (7.6L) \
1987-88
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.5 Qts. (8.0L) \
Cooling System (
2)
4-Cylinder .................................. 10.0 Qts. (9.5L)
6-Cylinder ................................. 12.0 Qts. (11.4L)
Engine Oil
4-Cylinder ................................... 4.0 Qts. (3.8L)
6-Cylinder ................................... 6.0 Qts. (5.7L)
Page 978 of 1378

Fuel Tank
Standard .................................. 13.5 Gals. (51.1L)
Optional .................................... 20 Gals. (75.7L)
Manual Transmission (
3)
AX4 (AISIN) .................................. 7.4 Pts. (3.5L) \
T4 (Borg-Warner) ............................. 3.9 Pts. (1.8L) \
AX5 (AISIN) .................................. 7.0 Pts. (3.3L) \
T5 (Borg-Warner) ............................. 4.5 Pts. (2.1L) \
Transfer Case
1985-86
Selec-Trac (229 Full-Time) ................. 6.0 Pts. (2.8L) \
Command-Trac (Part-Time 207) ............... 4.5 Pts. (2.1L) \
1987
Selec-Trac ................................. 2.5 Pts. (1.2L)
Command-Trac ............................... 2.2 Pts. (1.0L)
1988
Selec-Trac ................................. 3.0 Pts. (1.4L)
Command-Trac ............................... 2.2 Pts. (1.0L)
Drive Axles (
3)
Front ........................................ 2.5 Pts. (1.2L)
Front (Disconnect Housing) .................. 5.0 Ozs. (0.15L) \
Rear ......................................... 2.5 Pts. (1.2L)
Rear (Trac-Lok) (
4) .......................... 2.5 Pts. (1.2L)
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
(
2) - Includes 2.3 qts. for coolant recovery bottle.
(
3) - Fill to bottom of filler plug hole.
(
4) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive first, then add new fluid.
\
\
\
\
\
\
\
\f
60,000 MILE (96,000 KM) SERVICE
60,000 MILE (96,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Check Fluid Levels
\b\
\
\
\
\
\
\
Check Cooling System Hoses and Clamps
\b\
\
\
\
\
\
\
Check Coolant Strength
\b\
\
\
\
\
\
\
Check Accessory Drive Belts
\b\
\
\
\
\
\
\
Check Exhaust System & Heat Shielding
\b\
\
\
\
\
\
\
Clean Battery and Battery Terminals
\b\
\
\
\
\
\
\
Clean and Lubricate Crankcase Inlet Air Cleaner
\b\
\
\
\
\
\
\
Inspect Brake System
\b\
\
\
\
\
\
\
Inspect Exhaust System
\b\
\
\
\
\
\
\
Adjust Drive Belt Tension
\b\
\
\
\
\
\
\
Adjust Idle - Propane Method (1987-88 Carbureted Only)
\b\
\
\
\
\
\
\
Page 979 of 1378

Choke Linkage
\b\
\
\
\
\
\
\
Ignition Timing
\b\
\
\
\
\
\
\
Lubricate Manifold Heat Control Valve (if equipped)
\b\
\
\
\
\
\
\
Clean PCV Breather (if equipped)
\b\
\
\
\
\
\
\
Clean EGR Passages (if equipped)
\b\
\
\
\
\
\
\
Inspect C/V Joint boots (4WD)
\b\
\
\
\
\
\
\
Inspect Underside of Vehicle (Bolts & Threaded Fasteners)
\b\
\
\
\
\
\
\
Check/Lube Manual Steering Gear
\b\
\
\
\
\
\
\
Check Drive Shaft Seals
\b\
\
\
\
\
\
\
Lubricate Ball Joints, Steering Linkage & Suspension
\b\
\
\
\
\
\
\
Lube Drive Shaft U-Joints and Slip Splines
\b\
\
\
\
\
\
\
Lube Front Axle Drive Joint and Pivot Bearings (4WD)
\b\
\
\
\
\
\
\
Inspect Front Wheel Bearings (4WD)
\b\
\
\
\
\
\
\
Suspension Bushings, Springs, Arms & Rear Jounce Bumpers
\b\
\
\
\
\
\
\
Parking Brake System
\b\
\
\
\
\
\
\
Inspect Shocks for Leakage
\b\
\
\
\
\
\
\
Inspect Tire Wear Pattern
\b\
\
\
\
\
\
\
Rotate Tires and Adjust Air Pressure (Including Spare)
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Ignition Cables
\b\
\
\
\
\
\
\
Distributor Cap and Rotor
\b\
\
\
\
\
\
\
Air Filter Element
\b\
\
\
\
\
\
\
EGR Valve & Tube (1987-92)
\b\
\
\
\
\
\
\
Vacuum Operated Emission Components (1987-92)
\b\
\
\
\
\
\
\
PCV Valve (
1)
\b\
\
\
\
\
\
\
Drive Belt (V-Type) (
2)
\b\
\
\
\
\
\
\
Flush and Fill Engine Coolant, if not done in last 24 months
\b\
\
\
\
\
\
\
Automatic Transmission Fluid, Filter and Adjust Bands
\b\
\
\
\
\
\
\
Accessory Drive Belts
Page 980 of 1378

\b\
\
\
\
\
\
\
Fuel Filter
\b\
\
\
\
\
\
\
Emission System Vacuum Hoses
\b\
\
\
\
\
\
\
Ignition Wires
\b\
\
\
\
\
\
\
Distributor Cap & Rotor
\b\
\
\
\
\
\
\
Battery
\
\
\
\
\
\
\
(
1) - Replacement is recommended by Chrysler at this time, but it
is not required to maintain the warranty on the PCV valve.
(
2) - Check and replace as needed.
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Automatic Transmission .......................... Dexron-IIE ATF
Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid
Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil (
1)
Gasoline Engine
Temperature Range
Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD
Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD
Drive Axles ................................ SAE 75W-90 API GL-5
Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5
Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5
Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid
Manual Transmission ........................ SAE 75W-90 API GL-5
Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB
Door & Hood Hinges ............................ Light Engine Oil
Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP
Power Steering Pump ....................... Power Steering Fluid
Transfer Case ................................... Dexron-IIE ATF
Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease
Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease
Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB
Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP
Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB
Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB
Weatherstrip .......................... Silicone Spray Lubricant
Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)
(
1) - SAE 10W-30 SH/CD is preferred.
(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive when changing fluid.
(
3) - For vehicles operating under heavy-duty towing conditions,
use SAE 75W-140 Synthetic lube.
NOTE: Before using SAE 75W-140 Synthetic the old fluid must
be DRAINED and FLUSHED with clean mineral based axle
lubricant. Then refill with new synthetic lube.
(
4) - Use low pressure grease gun to prevent seal damage.
(
5) - Fill until lubricant squeezes out from the base of seals.
(
6) - Fill ball joint until seal starts to swell.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application ( 1) Quantity
Page 981 of 1378

Automatic Transmission
1984-86 (904 HD)
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.0 Qts. (7.6L) \
1987-88
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.5 Qts. (8.0L) \
Cooling System (
2)
4-Cylinder .................................. 10.0 Qts. (9.5L)
6-Cylinder ................................. 12.0 Qts. (11.4L)
Engine Oil
4-Cylinder ................................... 4.0 Qts. (3.8L)
6-Cylinder ................................... 6.0 Qts. (5.7L)
Fuel Tank
Standard .................................. 13.5 Gals. (51.1L)
Optional .................................... 20 Gals. (75.7L)
Manual Transmission (
3)
AX4 (AISIN) .................................. 7.4 Pts. (3.5L) \
T4 (Borg-Warner) ............................. 3.9 Pts. (1.8L) \
AX5 (AISIN) .................................. 7.0 Pts. (3.3L) \
T5 (Borg-Warner) ............................. 4.5 Pts. (2.1L) \
Transfer Case
1985-86
Selec-Trac (229 Full-Time) ................. 6.0 Pts. (2.8L) \
Command-Trac (Part-Time 207) ............... 4.5 Pts. (2.1L) \
1987
Selec-Trac ................................. 2.5 Pts. (1.2L)
Command-Trac ............................... 2.2 Pts. (1.0L)
1988
Selec-Trac ................................. 3.0 Pts. (1.4L)
Command-Trac ............................... 2.2 Pts. (1.0L)
Drive Axles (
3)
Front ........................................ 2.5 Pts. (1.2L)
Front (Disconnect Housing) .................. 5.0 Ozs. (0.15L) \
Rear ......................................... 2.5 Pts. (1.2L)
Rear (Trac-Lok) (
4) .......................... 2.5 Pts. (1.2L)
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
(
2) - Includes 2.3 qts. for coolant recovery bottle.
(
3) - Fill to bottom of filler plug hole.
(
4) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive first, then add new fluid.
\
\
\
\
\
\
\
Service Labor Times
\
\
\
\
\
\
\
Application Hours
2.5L
Automatic Transmission ................................... 3.5
Manual Transmission ...................................... 3.5
2.8L
Automatic Transmission ................................... 3.7
Manual Transmission ...................................... 3.7
4.0L
Automatic Transmission ................................... 3.6
Manual Transmission ...................................... 3.6
\
\
\
\
\
\
\
\f
67,500 MILE (108,000 KM) SERVICE
67,500 MILE (108,000 KM) SERVICE
Page 982 of 1378