2013 SSANGYONG NEW ACTYON SPORTS Service Manual

07-37810-01
1. SPECIFICATIONS
Unit Item Specification
Wiper motor Rated voltage DC 12 V
Operating voltage DC 10 to 15 V
Lowest operating voltage DC 8 V or less
Low revolutions46 ± 5 RPM
High revolutions70 ± 9 RPM
Wiper arm and blade Wiper arm length Driver 508 mm
Passenger 537 mm
Wiper blade
lengthDriver 550 mm
Passenger 475 mm
Rain sensor Operating voltage DC 9 to 16 V
Load Max. 200 mA (relay load)
Operating temperature-30˚C to 85˚C
Mounting location Top center of inner side of windshield
glass
Washer reservoir tank Volume 3.0 L

07-4
2. MAJOR CHANGES
Wiper blade
- Changed from conventional type to aero blade type
- No change in wiper blade dimension and wiper arm
Driver: 550 mm (22 inches) Driver: 550 mm (22 inches)
Passenger: 475 mm (19 inches) Passenger: 475 mm (19 inches)

07-57810-01
3. CAUTIONS ON RAIN SENSOR
When the wiper switch is in the AUTO position, the wiper will operate for 1 cycle if the initial engine
start is made. This may cause the wiper blades to wear prematurely. Therefore, other than rainy days,
set the switch to the OFF position. Especially during the winter time, check if the wiper blades are not
frozen to the windshield.
Operating the wiper with the blades frozen can damage the wiper motor.
If you operate the wipers when the windshield is dry without spraying washer fluid, the windshield can
be scratched and the wiper blades can wear prematurely. Use the wiper with the washer fluid when
the windshield is dry.
When it does not rain, turn the wiper switch to the OFF position.
Turn the wiper switch to the OFF position before any car wash to avoid unwanted operation of the
wipers. -
-
-
-
When cleaning the windshield over the sensor with damp clothes, the wiper may operate suddenly. It
could cause serious injury. Make sure to place the wiper switch to the OFF position and ignition
switch OFF when not in use.
Irregular operation (abrupt operation) ▶
Check if the sensor is off the position.
Check if the rain sensor cover is securely installed.
Check if the customer is familiar to how to control the wiper sensitivity.
Check if the wiper sensitivity control is set to the FAST side (step 5).
Check the wiper blade for wear.
If the wiper blade cannot wipe the glass uniformly and clearly, it may cause the rain sensor to work
irregularly. Therefore, in this case, replace the wiper blade with a new one. -
-
-
-

07-6
1. OVERVIEW
The wiper & rain sensor system consists of the multifunction wiper switch, windshield wiper motor and
linkage, wiper arm and blade, rain sensor, wiper relay (LO/HI) and washer tank. The rain sensor does
not directly operate the rain sensing wiper and it sends only the data of the rainfall to the STICS. The
basic operation of the wiper and washer is controlled by the STICS according to the signal regarding the
multifunction switch operation modes (MIST, AUTO, LO/HI, washer, sensitivity adjustment).
Layout ▶
Windshield wiper motor & linkage
When the driver operates the switch so that
the wiper motor is activated, the linkage
converts the rotary motion to reciprocating
motion and transfers it to the wiper arm.
Windshield wiper arm & blade
It receives the power from the wiper linkage
and does a reciprocating motion (left to right).
Washer nozzle
Installed on both sides of the cowl grille
assembly (one on each side). Sprays washer
fluid in fan-shape to cover the windshield
area as much as possible.Washer reservoir tank
Tank that supplies washer fluid to front
washer system.

07-77810-01
Emitter lens
The LED which is located at
bottom emits the infrared rays and
the lens guides the infrared rays to
target point.
Auto light sensor
Enlarged auto light sensor section
Auto light sensor (Vertical)
Auto light sensor (Horizon)
Wiper (HI, LO) relays
Used 3-way relay consisting of 5-pinSTICS
It receives the signals regarding the rain
sensor, multifunction wiper switch and
vehicle speed to control the wiper system
with the various functions.
Multifunction wiper switches
AUTO: Wiper operates automatically by rain
sensor
FAST to SLOW: Auto delay/auto speed control. A
position that can control sensitivity against rains
on the windshield and transmits wiping demand
signal accordingly.
Wiper relay (LO) Wiper relay (HI)
Rain sensor unit
Integrated into the auto light sensor. Detects and sends amount of rain drops to STICS

07-8
2. FUNCTIONS
1) Wiper and Washer Fluid Switch Operation
The wiper operates for 1 cycle when pushing
up the lever. The lever will return to the
"OFF" position when released.Front Automatic Wiping Speed
Control Switch
Fast: Fast interval
Slow: Slow interval
Stop the operation.
Operates automatically
according to the vehicle speed
or amount of rain.
Continuous wipe,
fast operation Continuous wipe,
slow operation
Front Auto Washer Switch (AFW)
When the front wiper switch is off
and this switch is pressed, washer
fluid will be sprayed and the wiper
will automatically operate 4 times.
Then, the fluid will be sprayed again
and the wiper will automatically
operate 3 times.
Wiper and Washer Coupled Operation
Pull the lever briefly (for less than 0.6 seconds):
One wiping cycle with washer spray Pull and hold the
lever for more than 0.6 seconds: Three wiping cycles with
washer spray Wiping without
washer spray
Wiping stopsMIST
OFF
AUTO
LO
HI

07-97810-01
2) Fluidic Washer Nozzle
Fluidic Washer Nozzle is applied to the front washer spray system in this vehicle. The inside of nozzle is
designed to utilize the fluidic movement.
This is a shape of the inside of nozzle. It is designed to change the spraying direction continuously
according to the spraying time (fan-shape). The figure below shows the changes of spraying direction
according to the spraying time.
It is designed to be changed spraying direction using the whirlwind and backflow generated in nozzle.Washer fluid inletSpray passage Counter-currentPassageWasher fluid outlet
Whirlwind

07-10
3) STICS Control Logic Related to Wiper and Washer
Wiper MIST and Front Washer Coupled Wiper ▶
The wiper relay is turned on 0.3 seconds after turning "ON" the washer switch for 0.1 ~ 0.59
seconds with the ignition key "ON", and it is turned off when the parking terminal is turned off. 1.
The wiper relay is turned on at 0.3 seconds after from the time when the washer switch is turned
on for more than 0.6 seconds with the ignition switch "ON". The wiper relay gets on 3 times
immediately after turning off the washer switch. 2.