2013 SSANGYONG NEW ACTYON SPORTS Service Manual

04-10
No. Symbol Item
24Engine oil pressure
warning lamp
25Water separator
warning light
26Engine coolant
overheat warning light
27Engine hood open
warning lamp
28 EBD warning light
29 SSPS warning lamp
30Hazard warning lampPower Turning ON condition
IGN Signal input
IGN IGN ON/ CAN signal input
IGN IGN ON/ CAN signal input
IGN Switch ground
IGN CAN signal input
IGN Digital input
IGN Switch to High

04-118210-01
2. CONFIGURATION
1) RPM Gauge
The tachometer indicates engine speed in revolutions per minute. Multiply 1,000 to the current number,
then it will be the current number of engine revolutions.
Under the normal engine operating temperature, the proper idling speed is 700 ~ 800 rpm. The red zone
(danger rpm range) starts from 4,500 rpm.
Connect the tachometer for tune-up test and start the engine.
Eliminate the hysteresis by tapping the tachometer.
Compare the values on the tester and tachometer and replace the tachometer if the tolerance is
excessive. 1.
2.
3.
If the tachometer (engine rpm gauge) pointer vibrates or stops moving at a certain range, or abnormal
noises are heard from the tachometer, the tachometer may have a malfunction. If you have reason to
suspect that the reading from the tachometer differs from the actual engine speed (rpm), connect a
diagnostic device and compare the value on tachometer with the reading from the diagnostic device.
Check Method

04-12
2) Speedometer Gauge
The speedometer indicates the vehicle speed by calculating the signals from the rear left and rear right
wheel speed sensors through ABS or ESP unit. (For the vehicle without ABS or ESP, the signals are
received from the EMS)
If the speedometer gauge vibrates, stops at a certain range or makes an abnormal noise, there could be
defectives in speedometer. However, these symptoms also could be occured when the tire has
uneven wear, different tire inflation pressures or different tire specifications.
Perform the speedometer test regarding the tolerance as described. However, it is not similar simple
work in field due to lack of measuring conditions such as test equipment and preciseness.
Check the allowable tolerance of the speedometer and operations of the trip odometer by using
a tester.
Check if the speedometer pointer is shaking and the abnormal noise sounds.
Eliminate the hysteresis by tapping the speedometer. 1.
2.
3.

04-138210-01
The allowable tolerance increases when the tires are worn or the tire pressure is out of specified
range.
Speed Input from ESP(ABS) or MS(ECU) ▶

04-14
3) Fuel Level Gauge
The fuel level gauge displays the resistance value of the float on the fuel sender in the fuel tank through
a pointer. Note that this vehicle doesn't have a service hole for checking the fuel sender connector in the
fuel tank.
The fuel sender and its connector can be checked and replaced only when the fuel tank is removed.
The power supply and resistance value should be measured at the connector in front of the fuel sende
r
(refer to wiring diagram).
When the power supply and output resistance are normal, the float operation by fuel level may be
defective; if so, replace the fuel sender.
Low fuel warning lamp comes on when:
The fuel level drops to 9 L or less. The lamp goes off if the fuel level reaches 9.5 L or more.This table shows the tolerance and resistance value changes by fuel level in normal conditions.
Therefore, the differences that can be occurred by the road conditions and fuel fluctuations are
ignored.

04-158210-01
4) Coolant Temperature Gauge
The coolant temperature gauge displays the coolant temperature with a pointer. The angle of pointer
that changes by coolant temperature is as shown below.
Measurement of coolant temperature sensor resistance
Measure the resistance between the terminal and the ground with an ohmmeter and replace if the
resistance is out of specified range.
Temperature (ºC)20 60 80 100 120
Resistance (Ω)2449Ω ± 5% 589.4kΩ ±
5%321Ω ± 5%185.7kΩ ±
5%112.9kΩ ±
5%
Voltage (V)3.615 1.910 1.259 0.819 0.536
When the resistance value by coolant temperature is within the specified range, check thermostat,
water pump, radiator related coolant circuit for normal operation. Also, check the wiring harnesses
and connectors for proper connection.

04-16
Change
OrderMode LCD Display Description
1 TRIP A The maximum distance value that can be displayed is
999.9 km with increments of 0.1 km. The trip meter is
reset to 0.0 km when the value reaches above 999.9 km.
When measuring a trip distance, reset the distance value
in the mode you want to use by pressing the TRIP switch
for 1 sec. or more.
2 TRIP B The maximum distance value that can be displayed is
6,213.09 mi with increments of 0.62mi. The trip meter is
reset to 0.0 km when the value reaches above 999.9 km.
When measuring a trip distance, reset the distance value
in the mode you want to use by pressing the TRIP switch
for 1 sec. or more.
3 Distance to
emptyThe estimated distance that can be traveled is calculated
based on the current fuel level.
If the DTE is less than 50 km, "---" flashes on the display.
4 Driving time The driving time from resetting the value (0:00) until now
is displayed. The value displayed is accumulated while
the engine is running even if the vehicle is not driven. The
display range is 00:00 to 99:59. When measuring the
driving time, press the TRIP switch for 1 sec. or more to
reset the value.
5 Average
fuel
economyThe average fuel economy from resetting the value (--.-)
until now is displayed. The value displayed is
accumulated while the engine is running even if the
vehicle is not driven. The display range is 0.0 to 99.9
km/h. When measuring the average fuel economy, press
the TRIP switch for 1 sec. or more to reset the value. "--.-"
is displayed on the screen when resetting. The value is
reset automatically whenever the vehicle is fuelled.
5) Description for LCD Display
LCD display
Mode Description ▶

04-178210-01
Change
OrderMode LCD Display Description
6 Instant fuel
consumptionThe fuel range is calculated based on the distance
driven and fuel consumed every 2 seconds. If the
vehicle speed is below 10 km/h or the engine rpm is
200 rpm or less, the instant fuel economy is not
displayed. The display range is 0.0 to 99.9 km/.
7 Brightness
adjustmentThe brightness of the illumination can be adjusted in 6
steps by pressing the TRIP switch briefly (less than 1
sec.). The display is changed from ILL1 to ILL6 every
time the switch is pressed. If you select one level
within the range and press and hold the TRIP switch,
the brightness level is memorized. If there is no TRIP
switch input for 5 seconds or more, the mode is
switched to TRIP A mode automatically. When the
battery is reinstalled, the brightness level is reset to
level 4.