2004 DACIA SOLENZA Repair Manual

57
57 - 9
INSIDE ACCESSORIES
Sun vi sors
DISMOUNTIN G
Dismount the sun visor (2) attachment screw (1).
Extract the sun visor from the hook ( 3).
REMOU NT I NG
Perform the dismounting operations in the reverse order.
vnx.su

57
57 - 10
INSIDE ACCESSORIES
Central c onsole
DISMOUNTIN G
Disconnect the battery.
Extract the ashtray ( 1) from its place.
Remove the gearbox lever covering ( 2) f rom
the central console.
Dismo unt :
- attachment screw ( 3) of the centra l
console on the tunnel; - attachment screw ( 4) of the centra l
console on the gearbox lever support. Detach the central console from the climate
maintenance- ve ntilating distri butor clips
(RACV) from points ( 5).
Swing over the diagnostic socket c ap and
push inside the console.
Disconnect the window lifting switch
connector (for vehicles equipped with electric
windows). Detach from clips the window-liftin g switch
and release the central console.
R EMOU NT I NG
Perform the dismountin g operations in the
reverse order. Che c k t he c orr e c t ope r a t i on o f t he
switches of the front electric windows.
vnx.su

57
57 - 11
INSIDE ACCESSORIES
Handb rake case
DISMOUNTIN G
Through the cutting out existent in the cock-
pit carpet in the handbrake lever, dismount the
attachment screw (1) of the handbrake case in
front part, on the tunnel.
Move towards front the seats.
Dismo unt :
- bench seat ( see c hapter 75); - attachmen
t screws of the front safety belts
at lower part; - attachment screws of the locks on the tun-
nel;
Detach from clips the carpet and roll it towards
front part.
Dismount the attachment screw ( 2) of the
handbrake case on the tunnel, in the rear part. Release the handbrake c ase.
REMOU NT I NG
Perform the dismounting operations in the re-
verse order. The safety belts screws are to be tighten to the
required moment of 2,7 daNm.
vnx.su

57
57 - 12
INSIDE ACCESSORIES
Tu r n i n g handle
DISMOUNTIN G
Dismount the screws from points A attaching the turning handle on the body roof.
Release the turning handle.
REMOU NT I NG
Perform the dismounting operations in the reverse order.
vnx.su

59
SECURITY ELEMENTS
59 - 1
F ront safety belts
1
4
3 2
TIGHTENING MOMENTS(daNm)
Fr
ont safety belt attachment screw 2.7
DISMOUNTING
Di smount:
-front/r ear door gasket (in the
contact area w ith the middle pillar
covering); -attachment scre ws (1) and (2) of
th e front safe t y be l t t o the uppe r pa rt,
conse quently, to th e lowe r part , on the
middle pillar lining; -
middle pillar c overing (see chapter
71); -attachment screw (3) of the safety belt
retriever on the middle pillar l ining. Dismount t he a ttachment scre w (4) of the
saf ety belt lock on the tunnel.
REMOUNTING
Perform t he di smounting operations in the
reverse order, taking into considera tion the
following: -retriever gui ding on t he centeri ng part
welded on the pillar. -the require d t ighte ni ng mome nt of
front the safety belts attachment screws is of
2,7 daNm.
vnx.su

SECURITY ELEMENTS
59
59 - 2
Rear safety belts
4
3 2
132 1
4
TIGHTENING MOMENTS(daNm)
Rear safety belt attachment scre w 2.7
DISMOUNTING
Di
smount t he t wo attachment screws of
the bench backre st. Sw ing over the bench backrest.
Di smount:
-r ear plate and its supports (see
chapter 74);
-belt attachment screws ( 2) and (3) o n
the side fra me lining. P
lace back t he bench backrest i n normal
position.
Sw ing over its supports the bench seat.
Dism oun t t he re a r b e lt attachment
screws ( 4) on the central floor.
REMOUNTING
Perform the dismounting operations in
the reverse order. The require d tightening moment of the
rear belt attachment screws is of 2,7 daNm.
vnx.su

61
HEATING
61 - 1
61General
1 – heating radiator
2 – cold/warm air flaps c ontrol
3 – air repartition flaps control
4 – air repartition control cable
5 – air-mixing control cable
a – air inlet
b – windscreen defogging exit
c – dashboard air vents exit
b
a 3 45 2c
1
vnx.su

61
HEATING
61 - 2
Operating principle
AIR TEMPERATURE CONTROL
The knob (A) is controlling the flaps for cold/warm air.
By rotating to the right the ( A) knob, the air temperature is increasing.
Cold air Warm air
The heating radiator is not having any valve and is permanently supplied. The flap controlled
by the cable ( 1) is ensuring the operation of the cold air re-heating system.
AA
1
vnx.su