2004 DACIA SOLENZA Repair Manual

19
19 - 6
COOLING - EXHAUST - TANKRadiator
* For the vehicles with air conditioning :
- Connect the t wo pipes to the condenser.
- Connect the engine fan resistance connector (1) and the engine fan connector, then attach
it by clips. Connect the battery.
Attach in clips the oil reservoir for power steering and the air inlet pipe on the battery screen.
Perform the cooling circuit filling and purging.
Perform the air conditioning circuit filling with refrigerant fluid HFC 134a (0.600 Kg) and
check for refrigerant fluid leak ( for vehicles with air conditioning).
vnx.su

19
19 - 7
COOLING - EXHAUST - TANK
Cooling engine fan for vehicles without air conditioning
DISMOUNTIN G
Disconnect the battery (-) terminal.
Remove the air inlet pipe from the attachment of the battery screen.
Detach from clips the oil reservoir of the power steering from the battery screen.
Disconnect the engine fan connector ( 1) and detach from clips wiring of point ( 2)
Dismount the four attachment screws ( 3) of the engine fan on radiator.
Carefully dismount the engine fan assembly from guiding points (4).
REMOUNTING
Check the condition of the fan impeller and of the engine fan electric motor.
Carefully position the engine fan assembly in the guiding points (4).
Mount the attachment screws ( 3) of the assembly on the radiator.
Connect the engine fan connector ( 1).
Attach in clips the wiring in point ( 2).
Attach in clips the power steering oil reservoir on the battery screen.
Mount the air inlet pipe.
Connect t he battery (-) terminal. In case the vehicle is equipped with programmable
r adio-cassettes player, e lectronic clock, etc, there are t o be re-programmed before returning
the vehicle to the client.
Check the engine fan operation: start the vehicle engine and disconnect the water
temperature sensor. The engine fan must start. Reconnect the water temperature sensor
then by means of the CLIP tester erase the memorized failure corresponding to the water
temperature sensor.
vnx.su

19
19 - 8
COOLING - EXHAUST - TANK
COOLING ENGINE FAN NOT WORKING
(for vehicles without air conditioning)
Replace fuse
F01
.
Check fuse F01 from engine compartment. Is it good?
Replace water temperature sensor.
Replace the control relay of the cooling engine fan.
Replace the cooling engine fan assembly . Start the vehicle’s
engine.
Disconnect the water
temperature sensor. Is the
cooling engine fan working?
Check the control relay of the cooling engine fan Is it good?
Is any voltage between pins 1
and 2 of the cooling engine fan connector?
The wirin g
is
damaged. Fix it. Stop the vehicle engine.
Check the continuity and resistance
against vehicle mass between:
- pin B2 connector of water temperature sensor pin 13 UCE i njection;
- pin B1 connector of water temperature sensor pin 73 UCE i njection;
- pin 3 connector of cooling engine fan control relay exit fuse F01;
- pin 5 connector of cooling engine fan control relay pin 2 connector of
cooling engine fan
- pin 1 connector of cooling engine fan vehicle mass;
- pin 1 connector of cooling engine fan control relay pin D 5 connector
of actuators relay;
- pin 2 connector of cooling engine fan control relay pin 8 UCE injection.
Ar e they good?
Replace UCE injection.
AT T E N T I O N !
The injection computer damaging i s probably due to an e lectric
shock. Before mounting a new injection computer, the cause of its
damaging must be found.No Ye s
Yes
No No
Ye s Ye s
No
Ye s
Diagnostic – failures interpretation
at vehicles without air conditioning
vnx.su

19
19 - 9
COOLING - EXHAUST - TANK
Cooling engine fan for vehicles with air conditioning
DISMOUNTIN G
Disconnect the battery (-) terminal.
Remove the air inlet pipe from the attachment of the battery screen.
Detach from clip the power steering oil reservoir from the battery screen.
Disconnect the engine fan connector ( 1)
Detach wiring from clips ( 2) and (3).
Disconnect the connector of the cooling engine fan resistance (4).
Carefully dismount the engine fan assembly from the radiator, from sustaining points (5).
REMOUNTING
Check the condition of the fan impeller and of the engine fan electric motor.
Carefully mount the engine fan assembly in the sustaining points (5).
Connect the connector of the engine fan resistance ( 4).
Connect the cooling engine fan connector ( 1) and attach it in clip (3) then in clip (2).
Attach in clips the power steering oil reservoir on the battery screen. Mount the air inlet
pipe.
Connect the battery (-) terminal. In case the vehicle is equipped with programmable
r adio-cassettes player, electronic clock, etc, there are t o be re-programmed before returning
the vehicle to the client. Check the engine fan operation: start the vehicle engine and disconnect the water
temperature sensor. The engine fan must start. Reconnect the water temperature sensor
then by means of the CLIP tester erase the memorized failure corresponding to the water
temperature sensor.
vnx.su

19
19 - 10
COOLING - EXHAUST - TANK
Diagnostic – failures interpretation at vehicles with air conditioning
vnx.su

19
19 - 11
COOLING - EXHAUST - TANKWa ter pump
DISMOUNTIN G
Place t he vehicle on a two columns elevator
Disconnect the battery
Drain the cooling circuit using the lower hose from the water pump.
Dismount :
- distribution belt ( see chapter 11 “Distribution belt”);
- tightening cam ( 1);
- water pump attachment screws and nut.
Remove the water pump through the upper part of the engine compartment.
TIGHTENING MOMENTS (daNm)
Tightening cam nut5
Crankshaft pulley hub screw2+680± 60
Right pendular support screws6.2
Hydro-elastic buffer nut3.7
W ater pump screws2.2
Water pump nut1
Wheels screws7.5
SPECIAL TOOLS
MOT. 1202-01 Pliers for elastic clips
MOT. 1505 Device for belts tension me asurement
MOT. 1135-01 Device for distribution belt tensioning
MOT. 545 Engine sustaining device
vnx.su

19
19 - 12
COOLING - EXHAUST - TANKWa ter pump
CL E ANING
It is very important not to scratch the surfaces for gaskets of the aluminum parts.
In order to dissolve the gasket particles stacked, product “ Decapjoint” is to be used.
A pply the product on the surfaces to be c leaned, leave it for a bout 10 minutes, then clean
using a wood palette knife. During performing this operation, use protection gloves.
REMOU NT I NG
The water pump sealing is ensured by means of LOCTITE 518 ; l ayer H, is 0.6 – 1 mm
thick and must be applied according to the bellow presented drawing. Remount the distribution belt (see chapter 11 “Distribution belt “).
Perform the cooling circuit filling and purging (see chapter “Filling – Draining”) .
vnx.su

19
19 - 13
COOLING - EXHAUST - TANKExhaust Assembly
ATTENTION !
Descending pipe in operation, may reach high temperatures and consequently must not
co me in contact with flammable materials which may lead to their auto-ignition.
Catalytic converter is to be mechanical shock protected.
DISMOUNTIN G
In order to di smount the noise a bsorber assembly ( 1), lift t he ve hicle on an elevator and
perform the following operation s:
Loosen the nuts ( 2) of the attachment collar between the expansion chamber ( 3) and the
noise silencer ( 1).
Di smount the thre e a ttachment e lastic supports of the noise a bsorber, on the carri age
body, rear pa rt. Release the noise silencer.
In order to dismount the assembled expansion chamber (3), perform the following operations:
Di smount the c ollar ( 4) and disengage the e xpansion chamber assembled with the de -
scending pipe.
Dismount the three elastic supports of the assembled expansion chamber.
Loosen the attachment collar nuts ( 2) and remove the assembled expansion chamber by
easy rotation and onward pulling.
In order to dismount the descending pipe assembly (6), perform the following operations:
Dismount the engine shield.
Dismoun t the catalytic converter attachment nuts ( 7) on the two studs of the exhaust manifold
flange. Dismount the attachment screws of the converter support ( 5).
For EURO 96, dismount the oxygen sensor located in upstream of the catalytic converter.
For EURO 00, dismount the oxygen sensors located in upstream, consequently, in
downstream of the catalytic converter.
Dismount the collar (4) and disengage the assembled catalytic converter from the assembled
expansion chamber.
Remove the descending pipe.
REMOU NT I NG
Perform the dismounting operations in the reverse order.
Ensure a perfect sealing between the exhaust assembly elements, using sealing paste Wurth,
on the joining area length (inside) between the noise absorber – expansion chamber (0.013 Kg);
The oxygen sensor gasket is to be replaced at each dismounting.
The tightening moment between noise absorber and expansion chamber is: 3.6 daNm.
The tightening moment of descending pipe attachment nuts on the exhaust manifold flange is:
2 daNm. Tightening moment between the catalytic converter and expansion chamber: 2.5 daNm.
All elements are to be assembled having the ambient temperature.
vnx.su