2004 DACIA SOLENZA Repair Manual

62
AIR CONDITIONING
62 - 23
Replace fuses F
03,
F04, F17 or F26. Check fuses F03, F04, F17 and F26 from
cockpit.. Are they ok?
Replace front wiring .Is any n12 V voltage between:
- vehicle’s
mass pin 10 climate control panel ?
- vehicle’s mass pin 11 climate control panel ?
- vehicle’s mass pin 10 blower connector ?
- vehicle’s mass pin 11 blower connector ?
- vehicle’s mass pin A5 climate control panel ?
- vehicle’s mass pin A4 climate control panel ?
Replace cold air blowing device. Di
sconnect the bl ower connector. Connect pin 14 and pi n 15 to
the vehicle mass. Connect F26 fuse exit, in turn, to:
- pin 3 blower connector (step 1).
- pin 4 blower connector (step 2)
- pin 5 blower connector (step 3)
- pin 12, pin 10 a nd pin 11 blower connector (step 4)
Blower working and there is 12 V voltage at pin 9 blower
connector?
Check the continuity and resistance against vehicle’s mass between:
- pin B5 climate panel pin 3 blower connector
- pin B4 climate panel pin 4 blower connector
- pin B1 climate panel pin 5 blower connector
- pin A1 climate panel pin 12 blower connector
- pin 13 climate panel pin 9 blower connector
- pin 14 climate panel pin 1 blower connector
- pin 15 climate panel pin 2 blower connector
- pin 9 climate panel vehicle mass
- pin 8 climate panel vehicle mass
- pin 14 blower connector vehicle mass
- pin 15 blower connector vehicle mass
Are they corresponding ?
Replace
front wiring .
No
No
No
Ye s Ye s
Ye s
No
No
Replace ventilation-
climate air distrib ut or .Disconnect
the recycling flap motor connector.
Start the recycling flap motor.
Is there 12 V between the pins of the recycling flap motor connector?
Ye s Ye s
Dia gnose
CLI
MATE BLOWER FAN OR RECYCLING FLAP NOT WORKING
vnx.su

62
AIR CONDITIONING
62- 24
Dia gnose
CLIMATE CONTROL PANEL LIGHTING NOT WORKING
Replace fuse F14.
Replace front wiring . Check in c ockpit fuse F14. Is it OK?
Check the continuity and resistance against vehicle mass between:
- cockpit fuse F 14 exit pin 7 climate panel;
- pin 9 climate panel vehicle mass.
Are they corresponding ?
Replace the ventilatio n-climate
air distributor.
No
No Ye s
Ye s
vnx.su

64
CARRIAGE BODY SEALING
64 - 1
1 - climate control protector
2 - climate control box gasket
3 - water evacuation hose
4 - bonnet support
5 - obturators
CLI MATE CONTROL PROTECTOR
DISMOUNTING
Dismount the climate control box gasket.
Sw ing over windscreen the climate control
prot e c t or a nd de t ach i t from c l ips from t he
climate control box.
REMOUNTING
Pe rform the dismou nting opera tions in the
reverse order. Take into considera tion that climate control
box gasket is sealing both on the border of the
climate control protector and on the central part
of the climate control box.
WATER EVACUATION HOSE
DISMOUNTING
Di smount
- climate control box gasket;
- climate control protector.
Remove the water evacuation hoses from
the climate control box.
REMOUNTING
Pe rform the dismounting operations in t he
reverse order.
3 1
2
5
4
Carriage body sealing
vnx.su

65
OPENINGS SEALING
65 - 1
1 – doors sealing gaskets
2 – trunk sealing gasket
3 – rear quart er panel ornament
4 – gutter sealing gasket
D OOR FRAMES GASKETS
DISMOUNTING
Di smount the front/rear doors frames gas-
kets following the their out liners, by draw-
ing towards outside of one of their ends.
Attention!
Ensure a good positioning of the seal-
ing gasket at the openings level.
GUTTER SEALING GASKETS
DISMOUNTING
Their dismounting is performed by pull-
ing of one gasket extremity t owards the e x-
terior of t he setting outliner.
REMOUNTING
M ounting is performed by placing one
gasket extremity on the gutter end by easy
and successive tapping by means of a rub-
ber hammer.
REMOUNTING
Introduce for a ll the contour of t ruk seal-
i ng g a ske t a se a l i ng m a t e ri a l Terodi c h t
Scwar tz.
The mounting of the gaskets is perform ed
by their t apping with a rubber hammer.
4 1
13
2
Op
ennings sealing
vnx.su

66
66 - 1
GLASSES SEALING
Glasse s gaskets
1. Windscreen gasket
2. Hatchback gasket
3. Fix window gasket
4. Doors glasses gaskets kit.
10 cm
5
8
67
4
1 3
2
DISMOUNTIN
G
Dismount the windscreen and hatchback
glass, together with the gasket by pushing from
the inside of the vehicle. If reused, the glass gasket shall be c leaned
or replaced with a new one.
R EMOU NT I NG
Place the gasket (6) all around the glass (5).
Apply in the gasket channelin the contact area
with carriage body a cord of sealaling material
Ro mtix 1502 P 3 mm di ameter. Int roduce a
cotton cord (8) of 3 – 4 mm diameter has been
previously introduced, leaving at the ends (7)
about 20 mm of cord, and between the ends,
the distance shall be not more than 10 mm. ATTENT ION:
Check if the gasket draining holes are
pierced.
vnx.su

66
66 - 2
GLASSES SEALING
Inside wipers
INSI DE WIPERS
DISMOUNTIN G
Dismount :
- opening handle;
- window regulator crank;
- inside door opening mechanism;
- panel attachment screws.
Remove the inside wiper.
R EMOU NT I NG
Perform the dismounting operations in the reverse order.
vnx.su

66
66 - 3
GLASSES SEALING
DISMOUNTIN G
Lower the window in the minimum position.
Dismount the outside wiper (1), by detaching it from the clips (2).
REMOU NT I NG
Perform in the reverse order the dismounting operation.
Outside wipers
vnx.su

66
66 - 4
GLASSES SEALING
1
Front door glass channel
DISMOUNTIN G
-front door panel (s ee chapter 72);
- front door deflective panel;
- inner and outside wiper;
- front glass (s ee chapter 54 );
- front door glass run channel;
- exterior mirror (s ee chapter 56).
REMOU NT I NG
Perform the dismounting operation in the reverse order.
vnx.su