2004 DACIA SOLENZA Repair Manual

VA LUES AND ADJUSTMENTS
07
07 - 1
Dimensions
Dimensions (mm)
Total length: 4083
T otal width:G = 1664
Total height:
* emptyH = 1379
*
loaded (authorized maximum total weight)1329
Wheel base* emptyA =2476
*
loaded2479
Front wheel track width, ground level measurement:
* empty E = 1429
* loaded1428
Rear wheel track width, ground level measurement F = 1348
Gr ound clearance (K)
*
empty-
*
loaded120
vnx.su

VA LUES AND ADJUSTMENTS
07
07 - 2
Optional e quipment weight disposal on shafts axles

Fr ont axle Rear axle
Air conditioning 230
Power steering 170
We i g h ts (kg)
Ve rsion
V ehicle type
Unloaded vehicle weight
Maximum authorized weight
on axle
Maximum technical
admissible weight of the
loaded vehicle
M aximum technical admissible towing
weight (trailer without braking system)
Maximum technical admissible towing
W eight (trailer with braking system)
Maximum admissible weight of the
assembly
Maximum load on towing hook
T owing hook weight 1,4
R5A715
1035592
443
1075 632
443 730
800
1450 718
732
450
800
2250 2260
40
20 R5A716
1045602
443
1085 642
443
1460 728
732
Minim
Front
Rear
Maxim
Front
Rear
Front
Rear
Total
Front
Rear
vnx.su

VA LUES AND ADJUSTMENTS
07
07 - 3
Capacity - Quality
DE NOM I NAT ION QUAL ITYCAPACITY (l)
(a pproximate )*
Engine oil DACIA OIL EXTRA SAE 10 W 40; API SJ 2,9*
Gearbox oil SAE 75 W 80 W; API GL 5 3,5
DACIA OIL EXTRAGEAR
Breaking fluid SAE J 1703 DOT 4 0,450
Cooling fluid 50% antigel GLACEOL RX typeD
50% distilled water 6
Refrigerant AC HFC – 134 a 0,600 kg
Compressor oil PA G S P 10 or SP 20 135 cm
3
* to be adjusted at dipstick
vnx.su

VA LUES AND ADJUSTMENTS
07
07 - 4
Accessories belts tension
Belts tensioning values are:
- alternator belt 253 – 273 Hz
- compressor belt 150 – 155 Hz
- power steering pumps belt 151 – 161 Hz
- compressor belt / DA pump 222 ± 8 Hz
A ccessories belt tensioning method.
Belt tensioning is to be performed with cold engine.
Mount the new belt.
Tighten the belt till obtaining the prescribed mounting tensioning.
Block the tensioner.
Perform three engine crankshaft rotations. P lace t he reading head of the MOT 1505 device i n the m easurement area and check if the
belt tensioning is within the mounting prescribed values; restore is necessary.
REMARK :
Once a belt is dismounted, is not to be remounted, but replaced.
A – crankshaft C – Compressor T – Tensioner pulley.
B – alternator D – Power steeri ng pump – Tensioning checking point.
B
A
A D
TA C
T
T
vnx.su

VA LUES AND ADJUSTMENTS
07
07 - 5
Wheels, Tires
Vehicle
SOLENZA Wheels
5.5J144 CH43
5.5B134CH46 Tires
165 / 65R14
165 / 70R13
Inflating pressure (bars) (1) Front Rear
Empty/Loaded Empty/Loaded 2.0/2.2 2.0/2.1
2.0/2.2 2.0/2.1
(1) Maximum loaded, wheels on the ground.
- tightening moment of the wheels screws : 7.5 daNm ;
- wheel axial run out : maximum 1 mm;
- wheel radial rubout : maximum 1 mm.
The increase of t ire t emperature during driving implies a growth of the tire pressure with
0.2 – 0.3 bars compared with t he prescribed values.
In case of tires pressure checking immediately after vehicle driving, consider this growth of
pressure.
vnx.su

VA LUES AND ADJUSTMENTS
07
07 - 6
Brakes
Veh icl e
Normal
20 Minim
19 Normal
228 Minim
229 Front
0.04 Rear
-
Brake disk width and drums diameter (mm) Front Rear Maxi
m disk
axia l run out
Veh icl e
Normal
14 Minim
7 Normal
5 Minim
0.5 mm
above the
rivets SAE J 1703
DOT 4
Gaskets thickness (mm)
Front Rear Bra ke fluid
SOLENZ A
SOLENZ A
vnx.su

VA LUES AND ADJUSTMENTS
07
07 - 7
Dimensions under c arriage body
DIMENSIONS UNDER CARRIAGE BODY CONDITIONING
ADJUSTMENT OPERATIONS OF THE STEERING ANGLES
H1, H4 - to be measured in front wheel axle, consequently rear wheel axle.
H2 - to be measured between the lower side of t he power train support.
H5 – to be measured between the elastic joint axle of the rear a xle arm and the ground.
vnx.su

VA LUES AND ADJUSTMENTS
07
07 - 8

Checking values of the front axle angles
ADJUSTMENTS
N
ot adjustable
N ot adjustable
N ot adjustable
Adjustable by
rotating the tie rod of the
steering rod
-
VE HICL E
POSITION
H5 - H2 = 100
H5 - H2 = 90
H5 - H2 = 80
H5 - H2 = 70
H5 - H2 = 60
H1 - H2 = 105
H1 - H2 = 98
H1 - H2 = 91
H1 - H2 = 85
H1 - H2 = 78
H1 - H2 = 71
H1 - H2 = 64
H1 - H2 = 105
H1 - H2 = 98
H1 - H2 = 91
H1 - H2 = 85
H1 - H2 = 78
H1 - H2 = 71
H1 - H2 = 64
N ot loaded
N ot loaded
VALUES
0
0 0 3'
0020'
0036' ± 30'
005 3'
101 0'
Right / left maxim
difference = of
10
-00 16'
-0010'
-0002'
0006' ± 30'
0015'
0024'
0035'
Right / left maxim
difference = of
10
130 36'
13025'
13014'
13003' ±30'
12050'
12038'
12024'
Right / left maxim
difference = of
10
Toe in:
0010' ± 10'
(for one wheel 0
005' ± 05')
-
ANGLES
CAMBER
CASTER
BALL JOINT
TOTAL PARALLELISM
ELASTIC BUSHINGS TIGHTENING
vnx.su