2004 DACIA SOLENZA Repair Manual

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 42
Diagnostic – General
This document is presenting the diagnostic generally valid for all computers, for anti-starting
function.
In order to perform the diagnostic of t his system, it is then all-i mportant t o dispose of the
following elements: -workshop manual of the corresponding vehicle
- electric diagram of the function, for the correspondin g vehicle
- special tools specified in the column “Necessar y Special tools”.
GENERAL ME THOD OF DIAGNOSTIC
- CLIP tester setting on, in order t o identify the system that is e quipping the vehicle
(identification of the computer family , program number, V. diagnostic..).
- Analysis of the “diagnostic” documents corresponding to the identified system.
- Acknowledgemen t of the information supplied in chapters “General”.
Reading of the memorised failure in the computer memory and taking advantage of the chapter
“Failures interpretatio n”.
Attention : each failure is interpreted for a specific type of memorisation : present failure,
memorised failure, present or memorised failure). The specified checking for handling each
failure are not to be applied on the vehicle unless the declared failure is interpreted in the document
for its specific memorising type. The memorising type must be taken into consideration when the
tester is set on, after setting off and on of the contact. If a failure i s interpreted in t he moment when i t is declare d “memorised”, t he diagnostic
applicatio n conditions are present in “Recommendations”. If the conditions are not fulfilled, yo u
must take the ideas from the diagnostic of damaged element circuit checking, because the failure
is not anymore present on the vehicle. Apply the same method when a failure is declared as been
memorised by the diagnostic tester, but it is interpreted in the documentation only as “present”
failure state.
-Performing the conformity checking (accentuatio n of the possible failures, non-declared
yet by the system self-diagnostic) and application of the adequate diagnostic according to the
results. - Reparation validation (elimination of “client’s effect”)
- Diagnostic exploitation by “Client’s effect” if the problem still on.
NECESSARY SPECIAL TOOLS FOR INTERVENT ION
-CLIP diagnostic tester
- ELE 1622 electric multi-socket
- All-purpose mete
r
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 43
OPERATION
When anti-starting system is on, the red LED is blinking (rare signal: one blink/sec).
After setting the contact on, the key code is transmitted to the Cockpit Central Unit.
If the code is recognized by the Cockpit Central Unit, this one is sending coded signals to the
injection computer and the anti-starting LED is off.
If signals issued by the Cockpit Central Unit and by the injection computer are matching, the
Cockpit Central Unit is authorizing the engine starting and the injection is unlocked.
SPECI AL SI TUATIONS
Injection computer does not have any reference code in m emory: the code sent by UCH is
written in the memory .
If there is no matching of the key c odes / Cockpit Central Unit, t he system is remaining
blocked and anti-star ting LED is blinking (quick signal). The vehicle starting is not authorized.
AT TE NT ION: when the battery is low charged, the voltage drop further to starter
action may reactivate the anti-starting. If voltage is too low, starting is impossible.
Key recognition in normal operation
Anti-starting indicator
Protected vehicle (without + after contact) Indicator slow blinking
Recognized key, non protected injection Indicator lighted for 3 seconds, then set off.
Non-recognized key Indicator is quickly blinking (at 4 Hertz)
Diagnostic – General
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 44
Diagnostic – General
-If doors are unlocked and none of them is
not opened in the next 30 seconds, the system
is automatically re-locking the vehicle doors
(without hazard lights blinking). -Cockpit central Unit is controlling the
vehicle inside lightening. In case a ceiling lamp
still lighted, Cockpit Central Unit is cutting the
supplying after approximately 30 minutes.
- The model “Full equipment” is controlling
the ceiling lamp progressive turning off, after
doors blocking by means of the remote control.
- Cockpit Central Unit may set on the hazard
lights in case of “shock connection” information
coming from UCE airbag.
-S pare parts keys are delivered not coded,
so they have no code.
-I t is possible in case of key’s l oss, theft or
by client’s request, that one vehicle ke y is
decommissioned. This one may be re-assigned
on the same vehicle, if necessary.
ATT E NT ION:
〈〈 〈〈
By this sy stem , i t i s i mp os s ib le th e
replacem ent of Coc kpit Central Unit and
keys in the same time. These parts are sold
not coded. 〈〈〈〈
The code me morized by the system’s
elements can not be erased (Cockpit
Central Unit and injection computer). The
memorized code can not be erased.
GENERAL
Cockpit Central Unit (UCH) is replacing
the UCE decoder.
Cockpit Ce ntral Unit is located under
dashboard, left side.
I MPORTANT
When replacing the Cockpit central Unit
it will be necessary to set the function
correspon ding to the vehicle equipment level,
by means of the CLIP tester.
ATT E NT ION
Starting is impossible unless the anti-
starting programming procedure is
performed.
When replacing a Cockpit Central Unit, it
is necessary to perform the programming and
settin g corresponding to the vehicle equipment
level.
When adding a key it is necessary that keys
re-assignation procedure be performed.
System’s characteristics.
- This system may work with maximum 4
remote controls (Cockpit central unit can
manage only 4 different codes).
-Radio-fr equenc y si gnal receive r i s
integrated in Cockpit Central Unit
-D oors central locking button is not
activated when doors ha ve be en c losed by
means of the remote control.
-Doors locking and unlocking using the
remote control may be visualized by hazard
lights signals (if all doors are properly closed);
- locking : 2 signals
- unlocking: 1 signal
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 45
Diagnostic – General
REPLACEMENT AND SETTING
Ne w parts are not coded. Once mounted on vehicle, in order to become under operation,
the memorization of a code it is necessary.
In order to perform this procedure, i t is absolutely necessary that some ve hicle parts are
already coded (with the vehicle code).
Refer to the assignations table:
ATTENTION :if a part is memorizing the code this one is assigned to this specif ic vehicle
and it is impossible that subsequently this c ode is erased or a second code is memorized. The
first time memorized code can not be anymore erased.
ASSIGNATION TAB LE
〈
The key assigned to a vehicle must be new and already programmed on that vehicle.
REMARK : this may be programmed n vehicle but it is not effective (not assigned).
ATTENT ION :
only the ke ys presented when performing this operation are to be under
operation.
AFT E R
SAL E
IN TE RVE N TION ELEMENTS CO
NDITION RE PARATI ON
CODE
NECESSITY
Cockpit Central
Unit Ke yInjection
co mputer
Cockpit Central Unit
programming
Key’ assignation or
deletion
Injec tion computer
programming new
c
oded
c oded c
oded
new *
c oded c
oded
-
new YES
YES
NO
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 46
Cockpit centra l Unit is not c oded. Once mounted on vehicle, i n order t o become under
operation, the memorization of a code it is necessary.
In order to perform this procedure, it is obligatory to have at least one of the vehicle old keys,
to know the reparation code and the injection computer must be correctly coded (please refer
to the assignation table). isvehicle, in order to become under operation, the memorization of a
code it is necessary.
I ATTENTION : if Cockpit Central Unit is memorizing a code, this one is assigned only to
that vehicle. It is impossible the code erasing or memorizing another code. eh old keys, to knhe
re IMPORTANT : only the keys presented when performing this procedure are becoming
under operation, with the condition:
- they have been already coded on this vehicle.
- they are ne w (not coded). icn c omputer m ust be correctly coded (please refe r to tho
R EMARK: if only Cockpit Central Unit is to be replaced, it is not necessary to perform
any intervention to the injection computer: this one will keep the same anti starting code.
SPECIAL SITUATIONS
If the screen displays:
“ Inserted after-sale code does not c or-
respond to the presented key. Check if the
code was correctly e ntered and if a vehicle
key was presented” : the code is not corre -
s ponding to the vehicle or a new key has been
used.
“Cockpit Central Unit is not empty. Start
the keys programming procedure” . Cock-
pit Central Unit is alre ady coded on this ve-
hicle. “Cockpit Central unit programming fail-
u re, key not possible to be used on this
vehicle”; the key code does not correspond
to the entered code (the key is be longing to a
vehicle of another type).
Diagnostic – General
PR OGRAMMING PROCEDURE OF
THE COCKPIT CE NTRAL UNIT
By means of the CLIP tester:
Enter in dialogue with system “Anti-start-
ing”. In menu “Control module”, “Spec ific
control ” , val idate line “SC027: Cockpit
Central Unit programming” The te ster is displaying “ Ta ke off the key
from anti-theft contact”
The te ster is displaying “Introduce the
after- sale code”. With the contact off, insert
the after-sal e secret code (12 hexadecimal
characters), the validate it.
If the code format is correct, the tester is
displaying “Insert an alre ady coded key on
the vehicle, set the contact on and then
va lidate” and the programming procedure is
under way. The t est er i s displ aying “ UCH pro-
grammed. Start the keys programming
procedure” and the Cockpit Central Unit is
coded. In this moment, it is necessary to enter
in the key programming mode, in order assign
the others keys (maximum four). More sec-
onds may pass before this message is displayed.
ATTENTION : the maximum interval between
each operati on is of 5 minute s if not the
procedur e is canceled.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 47
THE PROCEDURE OF COCKPIT CENT RAL UNIT PROGRAMMING
Diagnostic – General
The code can be entered only whencontact is et off
Enter in dialogue with system “Anti-starting”
Select menu “Control menu” and “Specific
control”.
S elect control “SC027 Cockpit Central
Unit Programming”.
T ester is displayin g:
“Take off the key from anti-theft contact”
Tester is displaying:
“Enter the after-sale code”
Enter t he code ( 12 hexadecimal
characters, capital l etters)
Tester is displaying:
“Insert an already programmed key on
vehicle”
Insert a key belonging to the vehicle and set
the contact on.
The procedure can not be performed with a
new key.
A
If tester is displayin g:
“Cockpit Central Unit is no
empty.
St art the key programming
procedure”.
Cockpit Central Unit is already
coded on this vehicle
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 48
Diagnostic – General
A
If tester is displayin g:
“The after-sale code does
no t correspond to the pre-
sented key. Check if the
code was correctly en-
tered and if a vehicle key was presented
”.
If tester is displayin g:
“UCH programming fail-
ure. K ey not in use on
this vehicle”. The entered c ode does not
correspond to the vehicle’s key, the key does not belong to t hat vehicle or it is new.
The ke y code does not
correspond with t he e ntere d code
(the key belongs to other vehicle).
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 49
Diagnostic – General
THE PROCEDURE OF
KEYS ASSIGNATION
IMPORTANT : if not all keys are available it
will be necessary to subsequently perform the
assignation procedure with all the keys.
Enter in dialogue with syste m “Anti-
starting” .
In menu ”Control menu”, “Spe cifi c
c ontrol” , validate line “SC028: Key program-
ming”. Tester is displaying: “Take off the key from
anti-the ft contact”.
Tester is displaying “Enter the after-sale
code” .
With contact set off, enter the after-sale se-
cret code ( 12 hexadecimal characters) and vali-
date it. Tester is displaying “Attenti on. Not pre-
se nted k eys will be not active. Re -launch
th e procedure in order to re-assign them”:
the programming is under way. Tester is displaying: “Insert key in anti-
theft contact and set the contact on, then
validate” : set the contact on using a vehicle key
or a new key. Tester is displaying: “No of programmed
keys 1” and “ take off the key from anti-
theft contact, then validate” .
Tester is proposing: “Do you wish to pro-
gram a new key ?”. In order to assign additional keys, set the con-
tact on few seconds using the vehicle’s others
keys that must be assigned (maximum four), then
validate. Tester is displaying: “2, 3, 4 programmed
keys” and “ take off th e key from anti-theft
contact”. ATTE NT I ON: t h es e on es mus t be t he
vehicle ’s old keys or new not coded keys.
Tester is displaying: “ Data entry in me mory”,
Cockpit Central Unit is coded and the keys are
a ssigned.Th is message will be displayed for few
seconds, then you may come out from the re-
a ssignation procedure
ATTENTION : the maximum admissible
interval between each operation is of 5 min-
utes otherwise the procedure is canceled.
Tester is displaying in this situation the
me ssage: “Pe r for ming co nditions not
ac c ompli shed”. T hi s me ss age is also
d isplayed in case of dialogue loss with the
Cockp it C entral Unit or in case of battery
supplying cutting off.
SPECI AL SI TUATIONS
If te ster is displaying:
“Coc kpit Central Unit is empty. Launch
the C ockpit Centra l Un it p rogrammi ng
procedure”, th en the Cockpit Central Unit is
no t used. It is impossible to assign keys to a
not coded Cockp it Central Unit.
“Per forming conditions not accom-
pli s hed ”, t he entere d code is not correct;
check and then start ag ain the code entering
procedure.
If the key does corres pond to the Cockpit
Central Unit of that vehicle, the tester is dis-
playing “Interrupted procedure: attention,
the keys assigned to the vehicle are the
on es that have been assigned before pro-
cedure s tarting. T he pr es ented k eys be-
fore proc edure interruptio n are not any-
more empty and can be only assigned to
th is vehicle” assigned.
vnx.su