2004 DACIA SOLENZA oil pressure

CHARACTERISTICS
Engine – Clutch - Gearbox .................................. 01-1
Ve hicle identification .......................................... 01-2
LIFTING MEANS
M obile jack – Adjustable supports ..................... 02-1
Elevator positioned under vehic le body .............. 02-2
TOWING
All types .............................................................. 03-1
LUBRICANTS – INGREDIENTS
C ondition ............................................................ 04-1
DRAINING – FILLING
Engine.................................................................. 05-1
Gearbox .............................................................. 05-2
P ower steering ..................................................... 05-3
VALUES AND ADJUSTMENTS
Dimensions .......................................................... 07-1
Weights (kg) ........................................................ 07-2
C apacity - Quality ................................................ 07-3
Accessories belts tension ..................................... 07-4
Wheels, Tires ....................................................... 07-5
Br akes.................................................................. 07-6
Dimensions under carriage body ......................... 07-7
Checking values of the front axle angles .............. 07-8
Checking values of the rear axle angle s .............. 07-9
ENGINE ASSEMBLY
Ingredie nts............................................................ 10-1
Oil consumption ................................................. 10-2
Oil pressur e ......................................................... 10-3
Power tr ain group................................................. 10-4
Sepa ration - Gearbox .......................................... 10-9
Se para tion – Unfitting ......................................... 10-10
Tightening moments ........................................... 10-11
S pecial tools ......................................................... 10-12
C haracteristics ..................................................... 10-13
Dismounting – Remounting ................................. 10-20
Lower casing ...................................................... 10-39
Oil pump .............................................................. 10-41
Mul ti-purpose support ......................................... 10-42
DISTR IBUTIO N SYSTEM
Dis t rib ution belt ........................................................ 11-1
Cy l inder head gasket ............................................... 11-3 FUEL MIX TURE
Characteri stics .......................................................... 1 2 -1
Bo d y valve ................................................................. 1 2 -4
In let man ifo ld ........................................................... 1 2 -5
Exh aust man i fold ...................................................... 1 2 -6
Air fi l ter .................................................................... 1 2 -7 FUEL SUPPLY
Su p ply interruptio n .................................................. 1 3 -1
Fu el ramp .................................................................. 1 3 -2
Pu mp capaci ty ........................................................... 1 3 -3
Su p ply pressure ......................................................... 1 3 -4 ANTI-POLLUTIO N
Pet rol vapors re-as p irat ion ...................................... 1 4 -1
Oil vapors re-as p irat ion ............................................ 1 4 -4 ALTERNATOR – STARTER
Alternat or ................................................................. 1 6 -1
Starter ........................................................................ 1 6 -6 IGNIT ION AND INJECTION
Ig nition system ......................................................... 1 7 -1
Sp ark pl ags ............................................................... 1 7 -3
In ject ion system ....................................................... 1 7 -4
Characteri stics .......................................................... 1 7 -10
In ject ion / ai r co nditioning strat egy ......................... 1 7 -11
Id ling reg ime co rrection ........................................... 1 7 -12
Id ling reg ime ad aptive co rrection ............................ 1 7 -13
Enri ching ad justment ............................................... 1 7 -14
Enri ching ad aptive co rrection .................................. 1 7 -16
“On Board Diagnostic” system ch aracterist ics ....... 1 7 -18
“On Board Diag nostic” li ghting conditions ............. 1 7 -19
“On Board Diag nostic” di agnostic conditions ......... 1 7 -20
Diag nostic of co mbustion mis fires det ection ............ 1 7 -21
Cat alyst diag nostic .................................................... 1 7 -22
Oxy gen sensor diag nostic ......................................... 1 7 -23
Diag nostic – Gen eral ................................................. 1 7 -25
Diag nostic – Fai l ures interp retat ion ......................... 1 7 -26
Diag nostic – Hel p ...................................................... 1 7 -60
Diag nostic – Confo rmity ch ecking ............................ 1 7 -61
Diag nostic – Stat es interpret ation ............................ 1 7 -69
Diag nostic – Paramet ers interp retat ion .................. 1 7 -75
Fai l ure locat ing al gorithm ........................................ 1 7 -83 COOLING - EXHAUST - TANK
Characteri stics .......................................................... 1 9 -1
Fi l ling - Purging ........................................................ 1 9 -2
Checking ................................................................... 1 9 -3
Co o ling system diagram ........................................... 1 9 -4
Rad i ato r ..................................................................... 1 9 -5
Co o ling engine fan fo r vehicles
wit h out ai r co nditioning ............................................ 1 9 -7
Diag nostic – fai lures in terp retat ion at vehicles
wit hout ai r co nditioning ............................................. 1 9 -8
Co o ling engine fan fo r vehicles
General poinds vehicle0
01
02
03
04
05
07
Engine and péripheriques1
10
11
12
13
14
16
17
19
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 3
SPECIAL TOOLS
MOT 836 - 05 Oil pressure measuring kit
CHECKING
The oil pressure is to be checked when the engine is warm (about 80°C).
Oil p ressure
For the engine E7J, components C + E + F from the oi l pressure measuri ng kit
MOT 836-05 are to be used.
The minimal pressure value should be:
1 bar at idling;
3 bar at 4000 rpm.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 4
Power train group
The power train dismounting-remounting is to be performed on the engine compartment upper
part by means of a mobile lifting device.
The vehicle i s to be placed on a 2–columns
elevator.
Dismo unt :
- battery
- air filter inlet pipe;
- air filter assembly ;
- engine bonnet;
- front wheels.
Disconnect the oxygen sensor ( 1) connector
or the connectors of the two oxyge n sensors
(EURO 00 ).
Di smount : thermal protection screen and
descending tube from the exhaust manifold.
DISMOUNTIN G
Drain:
- the cooling circuit on the water pump
inlet pipe; - oil from gearbox;
- oil from engine if necessary;
- refrigerant fluid to a charging station
(vehicles with AC);
- oil from the power steering circuit
(vehicles with power steering).
- Oil from the power steeri ng circuit
(vehicles with power steering);
Dismo unt :
- engine shield;
- descending tube attachment screws
on support;
TIGHTENING MOMENTS) (daNm)
Right support attachment screw on engine 6.2
Hydr o-elastic buffer attachment nut 3.7
Left elastic buffer attachment nut 6.2
Whe els s c rew s 7.5
Power train- battery attachment screws 2.1
Connecting rod attachment nut on steering cross member support 6.2
Anti-roll connecting rod attachment screw on gearbox connecting rod 10.5
Control bar attachment screw on gearbox connecting rod 2.7
Pipes a ttachme nt s crews on comp ressor 2.1
High pressure pipe on DA pump 2.1
1
23
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 7
Power train group
Dismount the hydro-elastic buffer nut (on
the right side).
Remove the power train and place it on a
support.
Disco n nect th e pr e ssu re controller
connector for power steering.
Dismo unt :
- hoses from oil reservoi r for power
s teering by means of pliers MOT 1202-01;
- high pressure pipe from the power
steering pump.
Dismount the refrigerant fluid pipes from
compressor (vehicles with AC unit).
Sustain the power t rain by means of the
two liftin g supports u sing a mobile lifting device
(mobile crane). Dismount the four attachment screws of the
power train support-battery and the elastic bu ffer
nut (9).
9
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 12
NO.DE NOM I NAT ION SERVICE DACI A
CODE ITEM NO
1O il plug wrench MOT 1018 1001101 800
2D evice for mounting the camshaft sealing gasket MOT 1127-01 1001112701
3Devic e for mounting crankshaft sealing gasket towards flywheel MOT 1129-01 1001112901
4Devic e for distribution belt tensioning MOT 1135-01 1001113501
5P liers for elastic clips MOT 1202-01 1001120 201
6Su itcase for petrol pressure checking MOT 1311-01 1001131101
7 Connection “J” MOT 1311-04 1001131104
8 Connection “K” MOT 1311-05 1001131105
9D evice for conne ction dismounting MOT 1311-06 1001131106
10 Pliers for valves oil seal ring dismounting MOT 1335 1001133 500
11 Device for checking the belt tensioning MOT 1505 1001150 500
12 Device for pi ston shaft mounting MOT 574-22 1001 0574 22
13 Sector for flywheel fixing MOT 582 1001 0582 00
14 Device for distribution gear blocking MOT 799-01 1001 0799 01
15 Device for mounting the crankshaft sealing gasket towards distribution MOT 550 1001 0550 00
16 Wrench for rockers adjustment MOT 567-01 1001 0567 01
17 Wrench for oil filter MOT 555 1001 0555 00
18 Device for power train sustaining MOT 545 1001 0545 00
19 Device for jackets maintaining MOT 484 1001 0484 00
or
Jackets maintaining clamps MOT 588 1001 0588 00
20 Comparing support MOT 251-01 1001 0251 01
21 Plate for measurement of cylinder jackets over-height MOT 252-01 1001 0252 01
Special tools
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 19
- clearance B (mm):
- minim 0.02
- maxim 0.86.
AT T E N T I O N !
Protect the distribution belt and the accessories belt in order to avoid the water and
cleaning materials splashing on them.
Chara cteristics
OIL PUMP
The oil pump is a gear wheels type.
Oil minimal pressure at 80°C is :
- at idling 1 bar
- at 4000 rpm 3 bar
Dismount the oil pump and check the
gearing clearances.
Check:
- cleara nce A ( mm)
- minim 0.110
- maxim 0.249
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 41
DISMOUNTIN G
Drain the oil from the engine.
Dismount :
- lower casing (see chapter 10”Lower casing on vehicle”).
Dismount the oil pump attachmen t screws on casing.
Dismount the drive chain from the oil pump gear.
Dismount the oil pump cap.
Check the gears clearance in the oil pump (see chapter 10” Engine assembly”)
REMOU NT I NG
Perform the dismounting operations in the reverse order;
Fill up engine with oil
Check the oil pressure at 80 °C:
At idling 1 bar;
At 4000 rot/min 3 bar. Oil pump attachment screws 2.5
Oil pump cap attachment screws 1

TIGHTENING MOMENTS (daNm)
O
il pump
vnx.su

ENGINE E7J-26211
11 - 3
DISTRIBUTION SYSTEM
3
1
42
Cylinder head gasket
N
ecessary Special Tools
MOT 1202-01 Pliers for e lastic collars
MOT 1505 Belt te nsioning measurement device
MOT 484 Jackets clamping device Wrench for angle tightening
Wrench for “CLIC” collars
TIGHTENING MOMENTS ( daNm )
Te nsioning roller nut 5
Crankshaft pulley screw 2 + 68° ± 6°
Pendular suspension support screws 6.2
Hydro-elastic buffer nut 3.7
Wheels screws 7.5
C ylinder head screws ( see cylinder head tightening method)
DISMOUNTIN G
Place the vehicle on a two-columns eleva-
tor. Disc onnect the battery.
Dr ain the cooling circ uit by the radiator
lower part hose.
Dismount the distribution belt (see chap-
ter 11 “ D i s t ribution belt “)
Dismount t he air filter
Disconnect : - acceleration cable from the valve con-
trol lever; -valve position potentiometer connec-
tor (1);
-atmospheric pressure sensor connec-
tor (2);
-step-by-step engine connector( 3);
- temperature sensor connector ( 4)
from the inlet manifold .
Disconnect :
-induction coil connector ( 5);
-f uel hoses (supply/return);
- injectors connectors;
- spark plugs cables.
Dismount the three attachment screws of the
induction coil ( 6).
vnx.su