2004 DACIA SOLENZA seats

01 - 5 A
PV IDENTIFICATION DATA
1.1Code type auto APV
1.2Manufacturing number
2.1 Equipping level code
2.2 Additional code for limited serial
definition 2.3 Additional code for special serial
definition
3.1 Carriage body color code
3.2 Seats upholstery code
3.3 Interior matching code.
4.1 Technical definition code
4.2 Optional equipping code.
A
C
D
F
B
H G
I
J E
MANUFACTURER’S
IDEN TIFICATION DATA
A. Manufacturer’s name
B. Community reception number or
homologation number. C. Identification number.
D. T otal autho r i zed weight of the
loaded vehicle. E. Total authorized running weight
F. T otal weight on front axle.
G. Total weight on rear axle.
H. Additional inscription.
I. Manufacturing date inscription
J. Consignment number.
The MANUFACTURER PLA
TE, self-adhesive type, has the bellow presented con-
figuration, with two distinctive areas, presenting :manufacturer’s identification data and
AP V type identification data.
01
CHARACTERISTICS
STA RTING WITH THE DATE OF 26.06.2003
Ve h i c l e identification
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 14
VA LVES SEATS
Sealing face angle
(α )
- intake 1200
- exhaust 900
Sealing face width (x)
- intake 1.7 ± 0.1mm
- exhaust 1.7 ± 0.1mm
External diameter (D)
- intake 38.5 mm
- exhaust 34.5 mm
VA LVES GUIDES
The valves for both intake and exhaust are provided with oil-rings, that must be replaced at
each valves dismounting.
Chara cteristics
Internal d iameter 7 mm
External diameter 12 mm
Position as against the spring seating on
cylinder head: - intake ( A) 12.34 mm
- exhaust ( E) 12.34 mm
Tilt as against vertical (ββββ
)1 7
0
vnx.su

FRONT AX LES ELEMENTS
31
31 - 7
Brake lining (pads)
REMARK :
In order to maintain the brake efficiency,
the replacement of the brake l ining (pads)
shall be made only in complete kit. Brake pads brand TEXTAR are to be used
as spare parts.
DISMOUNTIN G
Loosen the front wheel attachment screws.
Lift the vehicle by means of a two-column
elevator.
Dismount the front wheel.
Disconnect the wear sensor wire.
Remove: - the safeties of the wedges ( 1);
- the wedges, by sliding them.
D etach the caliper assembly from the fork
together with the flexible hose.
Remove:
- the brake pads from fork seats
(maintaining springs are attached with them);
- the maintaining springs from the brake
pads. REMARK :
It is forbi
dde n t o push the brake
pedal after the c alipers were
dismounted from the fork. If the brake pads are not fully used
but on their friction surface, especially
in the middle pad channel, there are
material traces, it is recommended the
cleaning of these surfaces in order to
avoid the noise when braking. Irregularly we ar of one brake pad or
wear diffe rences between t he inner pad
the outside pad, greater than 10% of the
minimum remaining l ining, impose the
kit replacement.
SPECIAL TOOLS
FR 500 P ushing piston device
1
vnx.su

36
STEERING ASSEMBLY
36 - 5
Noise absorbant bushing
DISMOUNTIN G
Loosen the screws of the right front wheel.
Lift the vehicle by means of a two-column elevator.
Dismount the right front wheel.
Dismou nt :
-steering box casing protection bellows-left steering rod end;
-the right steering connected rod.
Rotate the steering wheel t o the right (complete turn), the rack is withdrawing towards left.
Remove, by means of a screwdriver the used noise absorber bearing.
R EMOU NT I NG
Carefully clean t he rack and the noise absorber bearing seat and grease with special grease
containing MoS2 and then mount the new noise absorber bearing.
Position the pins (A) in their casing seats.
Rotate the steering wheel to the left until t he rack stands out the bearing.
Remount on the rack: - the steering c onnecting rod (safety washer and limiter washer a re t o be obligatory
positioned on the threaded side of the joint body); -protection bellows.
Check and adjust the parallelism, if necessary.
A
A
vnx.su

THE M ECHANICAL ELEMENTS CONTROLS
37
37 - 8
Handbrake control lever
TIGHTENING MOMENTS (daNm)
Attachment screws of the handbrake lever on c entral floor 1.2
DISMOUNTIN G
Disconnect the battery.
Release the hand brake control lever ( released position).
Lift the vehicle by means of a two columns elevator;
Detach the rudder bar fork ( 5) from the end rod (3) by unscrewing the lock nut (1) and
remove the ball-ended washer ( 2).
Remove the secondary cables ends from rudder bar seats.
D etach from clips the rod ( 3) from rudder bar (4)
Lower the vehicle from the elevator and inside the vehicle dismount: - seat;
- carpet attachment clips in the rear side area
- inner attachment of the left/right middle pillars coverings.
M ove the front seats backwards and dismount the a ttachment screw (6) of the handbrake
control on the central floor.
3 4521
vnx.su

THE M ECHANICAL ELEMENTS CONTROLS
37
37 - 9
Move the seats a head and dismount:
- safety belts lower attachment screws;
- attachment screws of the front safety
belts locks and remove them.
Clear the cockpit carpet towards front seats.
Dismount the handbrake control attachment
screw ( 7) on the central floor.
Remove the upper casing of the handbrake
(8).
Han dbrake control lever
Disconnect handbrake contact (9).
Take off the assembly handbrake.
RE MOUNTIN G
Grease the shaft s with UM 185 Li 2M
grease.
Perform the dismounting operations in the
reverse order, taking care to apply a sealant
material layer on the outline of lower casing of
the handbrake lever assembly .
Readjust the handbrake.
vnx.su

THE M ECHANICAL ELEMENTS CONTROLS
37
37 - 10
Handbrake secondary cables
SECONDARY CABLE - REPLACEMENT
DISMOUNTING
Disconnect the battery.
Loosen the rear wheels attachment screws.
Release the ha nd brake control l ever (re-
lease position).
Lift the vehicle by means of a two-column
elevator.
Detach the rudder ba r fork from the end
rod by unscrewing the lock nut (M12 x 1.25)
and remove the ball-ended washer.
Remove the secondary cables ends from
rudder bar seats.
Dismount the two rear wheels.
Dismount the brake drums ( see chapter 33
– Rear axles e leme nts ). Remove the secondary cables stops from
the central floor. Dismount the sheathe stops from the brake
plates. Remove the secondary cables.
REMOU NT I NG
Grease the cable with UM 185 Li 2M
grease
Perform the dismounting operations in the
reverse order.
Adjust the drum clearance ( see chapter 33-
Rear axles elements ”).
Adjust the handbrake control lever stroke.
SPECIAL TOOLS
Ro 441 Wheel drum cover tongs
Fr.600 Hub extractor
TIGHTENING MOMENTS (d aNm)
Wheel attachment screw 7.5
Steering knuckle nut 16.5
vnx.su

INSIDE ACCESSORIES
Dashboa rd .......................................................... 57-1
Inside rear view mirror ..................................... 57-8
S un visors ........................................................... 57-9
Central console ................................................. 57-10
Handbrake case ................................................ 57-11
Turning handle .................................................. 57-12
SECU RITY ELEMENTS
Fr ont safety belts ............................................... 59 - 1
Re ar safety belts ............................................... 59 - 2
HEATING
General .............................................................. 61-1
Operating principle ........................................... 61-2
C limate c ontrol unit .......................................... 61-4
Ve n t ilation- climate control air
distributor (RACV) .......................................... 61-5
Heating radiator ................................................ 61-6
C ontrol panel ..................................................... 61-7
C ontrol cable s ................................................... 61-9
Motor fan control resistance............................ 61-10
Diagnose ............................................................. 61-11
AIR CONDITIONING
General ............................................................... 62-1
Draining – filling the refrigerant circuit ......... 62-3
Air conditioning unit operating diagram ........ 62-4
Operating principle ........................................... 62-5
Part icles filter .................................................... 62-7
Cold ai r blowing device (DSAF) ...................... 62-8
Evaporator ........................................................ 62-10
Control panel ..................................................... 62-11
Comp ressor ........................................................ 62-12
C ondenser .......................................................... 62-13
Pressu re controller ............................................ 62-14
F ilter reser voir ................................................... 62-15
Unit piping ......................................................... 62-16
Thermostatic expansion valve ......................... 62-19
C limate c ontrol blower ..................................... 62-20
Blow er control resistance .................................. 62-21
Rec ycling flap motor fan ................................. 62-22
Diagnose ............................................................. 62-23
CARRIAGE BODY SEALING
Ca rriage body se aling ....................................... 64 - 1 OPENINGS SEALING
Opennings sealing ............................................. 65 - 1 GLASSES SEALING
Glasses gaskets .................................................. 66 - 1
Inside wipers ..................................................... 66 - 2
Outside wipers ................................................... 66 - 3
Fr ont door glass channel ................................. 66 - 4
Rear door gla ss run channel ............................ 66 - 5
CARRIAGE BODY INSIDE TRIMS
C arriage body inside trims ............................. 71-1
Upper front pillar trim ..................................... 71-2
Mi ddle pillar trim ............................................. 71-3
Rear quarter panel tr im ................................... 71-4
R oof lining ......................................................... 71-5
Trunk carpet ...................................................... 71-6
Cowl panel noise absor bent ............................. 71-7
Cockpit carpet ................................................... 71-8
LATERAL OPENINGS TRIMS
Fr ont door panel ................................................ 72-1
R ear door panel ................................................. 72-2
REAR TABLE
Lateral table ....................................................... 74-1 FRONT SEATS SLIDES GUIDES
Fr ont seat ........................................................... 75-1
Fr ont seats slides guide s ................................... 75-2
SEATS / R EAR BENCH
R ear bench ......................................................... 76-1
BATTERY - FRONT HEADLIGHTS
Battery ... ............................................................ 80-1
Headlamp assembly .......................................... 80-4
F og projectors ................................................... 80-5
Bulbs ... ................................................................ 80-6
Headlamps adjustment .................................... 80-9
Repl acement of the headlamps mechanic
adjustment control ........................................... 80-1157
Mechanisms and accesoires5
59
61
62
Climatisation6
64
65
66
71
72
74
75
76
80
Echuipment electr ique8
Garnishing and tack room7
vnx.su