2004 DACIA SOLENZA height

VA LUES AND ADJUSTMENTS
07
07 - 1
Dimensions
Dimensions (mm)
Total length: 4083
T otal width:G = 1664
Total height:
* emptyH = 1379
*
loaded (authorized maximum total weight)1329
Wheel base* emptyA =2476
*
loaded2479
Front wheel track width, ground level measurement:
* empty E = 1429
* loaded1428
Rear wheel track width, ground level measurement F = 1348
Gr ound clearance (K)
*
empty-
*
loaded120
vnx.su

VA LUES AND ADJUSTMENTS
07
07 - 9
Checking values of the rear axle angles
ADJUSTMENTS
Not adjustable
N ot adjustable
VEHICLE
POSITION
Unloaded
Unloaded
Unloaded
VA L U ES
0030' ± 10'
(For two wheels) Cl osing
0
030' ± 10'
2,9 mm ± 1 mm
ANG L E S
CAMBER
PARALLELISM
ELASTIC BUSHINGS TIGHTENING
PRELIMINARY OPERATIONS TO BE OBSERVED BEFORE
CHECKING THE STEERING ANGLES
1. Area (checking surface) – it must be a s horizontal as possible.
2. Wheels, tires – check (from e quipping point of vi ew) to have same type of wheels and
tires on bot h axles (dimensions, inflating pressure, wear de gree). A pronounced wear i s not
allowing the correct horizontal positioning.
3. Suspension – check the shock absorbers, springs condition and height symmetry under
carriage body.
4. Joints – check the e lastic joints condition, steering and suspension ball joints clearance,
bearings clearances of the front and rear axles 5. Radial and axial run out of the wheels – must not be over 1 mm. This will be compensated
with the reading instruments. 6. Manufacturer’s method – each vehicle manufacturer is providing the checking conditions,
axles weights repartition, and presentation of under carriage body heights, not loaded.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 12
NO.DE NOM I NAT ION SERVICE DACI A
CODE ITEM NO
1O il plug wrench MOT 1018 1001101 800
2D evice for mounting the camshaft sealing gasket MOT 1127-01 1001112701
3Devic e for mounting crankshaft sealing gasket towards flywheel MOT 1129-01 1001112901
4Devic e for distribution belt tensioning MOT 1135-01 1001113501
5P liers for elastic clips MOT 1202-01 1001120 201
6Su itcase for petrol pressure checking MOT 1311-01 1001131101
7 Connection “J” MOT 1311-04 1001131104
8 Connection “K” MOT 1311-05 1001131105
9D evice for conne ction dismounting MOT 1311-06 1001131106
10 Pliers for valves oil seal ring dismounting MOT 1335 1001133 500
11 Device for checking the belt tensioning MOT 1505 1001150 500
12 Device for pi ston shaft mounting MOT 574-22 1001 0574 22
13 Sector for flywheel fixing MOT 582 1001 0582 00
14 Device for distribution gear blocking MOT 799-01 1001 0799 01
15 Device for mounting the crankshaft sealing gasket towards distribution MOT 550 1001 0550 00
16 Wrench for rockers adjustment MOT 567-01 1001 0567 01
17 Wrench for oil filter MOT 555 1001 0555 00
18 Device for power train sustaining MOT 545 1001 0545 00
19 Device for jackets maintaining MOT 484 1001 0484 00
or
Jackets maintaining clamps MOT 588 1001 0588 00
20 Comparing support MOT 251-01 1001 0251 01
21 Plate for measurement of cylinder jackets over-height MOT 252-01 1001 0252 01
Special tools
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 13
Chara cteristics
CYLINDER HEAD
The cylinder head is not to be re-ti ghtened.
The rockers adjustment is to be performed onl y at cold, only i n case of engine reparation
influencing their clearance. The adjustment values are:
- for admission: 0.10 mm;
- for exhaust: 0.25 mm.
Cylinder head height 113 ± 0.05 mm
Maximal deformation on the gasket plane 0.05 mm
The cylinder head is not to be r ectifi ed
Combustion chamber volume (with valves and spark plugs) 26.25 cm
3 ± 0.6
Spark plugs tightening moment 2.5 - 3 daNm
VA LVES
V alve rod diameter 7 mm
Sealing face angle:
- intake 120
0
- exhaust 900
Tray diameter:
- intake 37.5 ± 0.1 mm
- exhaust 33.5 ± 0.1 mm
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 17BOLTS
Length (mm)
60
External diameter (mm) 19
Internal diameter (mm) 11
CYLINDER JACKETS
T ype: wet removable.
The sealing gasket is J rubber ring type.
Internal diameter (mm) 75.8
Jacket height (mm) H2 130
Centering diameter (mm) D80.6
Jackets over-height X without
gasket (mm) 0.02-0.09
Jacket height (mm) H1 91.5
Deep in cylinder block K1 (mm)
91.5+ 0 ,03
Chara cteristics
+ 0 ,035
+ 0 ,005
- 0 ,015
- 0 , 055
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 28
CYLINDERS BLOCK REMOUNTING
Clean the cylinders block, especially t he
jackets s eating and sealing surfaces.
Preparation of assembly
“ pistons-jackets”
The parts contained in the kit are in pairs.
Ma rk the part s assembly from A to D in
order to keep the matching.
Dismounting – Remounting
Remove completely the anti-rust foil.
REMARK:
Never scrape the parts. Jackets over-height
These engines are equipped with rubber
rings for jackets sealing, ensuring only the seal-
ing, jackets being seated directly on the cylin-
ders block and over-height being done from
manufacturing. The checking of the jackets over-height is
to be performed as follows: - place the jackets in the cylinders block
without the sealing ring;
- check t he X over-he ight by means of
the devices MOT 251-01 and MOT 252-01.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 29
Dismounting – Remounting
The over-he ight X must be between 0.02
mm and 0.09 mm.
Place the jackets in such way that :
-the difference between two joint jackets
to be maximum 0.05 mm;
- the over-height to be in ascending order
between cylinders 1 and 4;
- in case of an incorrect over-height, check
the over-height by m eans of a new kit of jack-
ets, i n order to see i f t he c ause i s the block or
the cylinders jacket or check the theoretical size
values of the block and of the jackets. When over-height is correctly obtained, per-
form the A, B, C, D assembly then mark with
numbers jackets, pistons and the bol ts from 1
to 4 (no.1 towards flywheel) so that the corre-
s pondence with the corresponding connecting
rods may be achieved.
Pistons bolts mounting
The pistons bolts are fixed in connecting rods
and free in pistons. Mount the pistons bolts by means of the
MOT 574-22 that is containing:
- a support for piston ( S);
- an extracting mandrel ( M);
- the piston supporting bushings (B);
- the bolts for mounting ( A) provided with
their centering guides (C ). Use an electric plate of
1500 W (electric
oven) for connecting rods heating. Place the connecting rods on the electric
plate so that connecting rod end surfaces are
in contact with the heating plate.
Check if the pistons bolts are freely gliding
in the new corresponding pistons. Mount the piston bolt E on the mounting
bolt A.
Sc rew the centering guide C till end and
then unscrew it for a quarter of turn.
vnx.su

GENERAL
30 - 6
30Composition and dimensions of the main
braking system elements
Front brakes
- brake caliper bore diameter → 54 mm
- brake disk diameter → 235 mm
- disk axial runout measured at → 215 0. 04 mm
- brake disk maximal thickness 20 mm
- brake disk minimal thickness 19 mm
- braking pad thickness (support included) 14 mm
- brake pad minimal thickness (support included) 7 mm
Rear brakes
- wheel braking cylinder bore diameter → 22 mm
- new drum diameter → 228 mm
- drum diameter after grinding → 229 mm
- braking shoes lining width 40 mm
- braking shoes lining thickness 5 mm
- minimal accepted braking lining height above rivets 0.5 mm
Master cylinder
- diameter of bore 20.6 mm
Brake fluid reservoir without alarm sensor
Pressure limiter for circuit in parallel
S ervobrake master vac 7" 177.8 mm
vnx.su