2004 DACIA SOLENZA belt

CHARACTERISTICS
Engine – Clutch - Gearbox .................................. 01-1
Ve hicle identification .......................................... 01-2
LIFTING MEANS
M obile jack – Adjustable supports ..................... 02-1
Elevator positioned under vehic le body .............. 02-2
TOWING
All types .............................................................. 03-1
LUBRICANTS – INGREDIENTS
C ondition ............................................................ 04-1
DRAINING – FILLING
Engine.................................................................. 05-1
Gearbox .............................................................. 05-2
P ower steering ..................................................... 05-3
VALUES AND ADJUSTMENTS
Dimensions .......................................................... 07-1
Weights (kg) ........................................................ 07-2
C apacity - Quality ................................................ 07-3
Accessories belts tension ..................................... 07-4
Wheels, Tires ....................................................... 07-5
Br akes.................................................................. 07-6
Dimensions under carriage body ......................... 07-7
Checking values of the front axle angles .............. 07-8
Checking values of the rear axle angle s .............. 07-9
ENGINE ASSEMBLY
Ingredie nts............................................................ 10-1
Oil consumption ................................................. 10-2
Oil pressur e ......................................................... 10-3
Power tr ain group................................................. 10-4
Sepa ration - Gearbox .......................................... 10-9
Se para tion – Unfitting ......................................... 10-10
Tightening moments ........................................... 10-11
S pecial tools ......................................................... 10-12
C haracteristics ..................................................... 10-13
Dismounting – Remounting ................................. 10-20
Lower casing ...................................................... 10-39
Oil pump .............................................................. 10-41
Mul ti-purpose support ......................................... 10-42
DISTR IBUTIO N SYSTEM
Dis t rib ution belt ........................................................ 11-1
Cy l inder head gasket ............................................... 11-3 FUEL MIX TURE
Characteri stics .......................................................... 1 2 -1
Bo d y valve ................................................................. 1 2 -4
In let man ifo ld ........................................................... 1 2 -5
Exh aust man i fold ...................................................... 1 2 -6
Air fi l ter .................................................................... 1 2 -7 FUEL SUPPLY
Su p ply interruptio n .................................................. 1 3 -1
Fu el ramp .................................................................. 1 3 -2
Pu mp capaci ty ........................................................... 1 3 -3
Su p ply pressure ......................................................... 1 3 -4 ANTI-POLLUTIO N
Pet rol vapors re-as p irat ion ...................................... 1 4 -1
Oil vapors re-as p irat ion ............................................ 1 4 -4 ALTERNATOR – STARTER
Alternat or ................................................................. 1 6 -1
Starter ........................................................................ 1 6 -6 IGNIT ION AND INJECTION
Ig nition system ......................................................... 1 7 -1
Sp ark pl ags ............................................................... 1 7 -3
In ject ion system ....................................................... 1 7 -4
Characteri stics .......................................................... 1 7 -10
In ject ion / ai r co nditioning strat egy ......................... 1 7 -11
Id ling reg ime co rrection ........................................... 1 7 -12
Id ling reg ime ad aptive co rrection ............................ 1 7 -13
Enri ching ad justment ............................................... 1 7 -14
Enri ching ad aptive co rrection .................................. 1 7 -16
“On Board Diagnostic” system ch aracterist ics ....... 1 7 -18
“On Board Diag nostic” li ghting conditions ............. 1 7 -19
“On Board Diag nostic” di agnostic conditions ......... 1 7 -20
Diag nostic of co mbustion mis fires det ection ............ 1 7 -21
Cat alyst diag nostic .................................................... 1 7 -22
Oxy gen sensor diag nostic ......................................... 1 7 -23
Diag nostic – Gen eral ................................................. 1 7 -25
Diag nostic – Fai l ures interp retat ion ......................... 1 7 -26
Diag nostic – Hel p ...................................................... 1 7 -60
Diag nostic – Confo rmity ch ecking ............................ 1 7 -61
Diag nostic – Stat es interpret ation ............................ 1 7 -69
Diag nostic – Paramet ers interp retat ion .................. 1 7 -75
Fai l ure locat ing al gorithm ........................................ 1 7 -83 COOLING - EXHAUST - TANK
Characteri stics .......................................................... 1 9 -1
Fi l ling - Purging ........................................................ 1 9 -2
Checking ................................................................... 1 9 -3
Co o ling system diagram ........................................... 1 9 -4
Rad i ato r ..................................................................... 1 9 -5
Co o ling engine fan fo r vehicles
wit h out ai r co nditioning ............................................ 1 9 -7
Diag nostic – fai lures in terp retat ion at vehicles
wit hout ai r co nditioning ............................................. 1 9 -8
Co o ling engine fan fo r vehicles
General poinds vehicle0
01
02
03
04
05
07
Engine and péripheriques1
10
11
12
13
14
16
17
19
vnx.su

VA LUES AND ADJUSTMENTS
07
07 - 4
Accessories belts tension
Belts tensioning values are:
- alternator belt 253 – 273 Hz
- compressor belt 150 – 155 Hz
- power steering pumps belt 151 – 161 Hz
- compressor belt / DA pump 222 ± 8 Hz
A ccessories belt tensioning method.
Belt tensioning is to be performed with cold engine.
Mount the new belt.
Tighten the belt till obtaining the prescribed mounting tensioning.
Block the tensioner.
Perform three engine crankshaft rotations. P lace t he reading head of the MOT 1505 device i n the m easurement area and check if the
belt tensioning is within the mounting prescribed values; restore is necessary.
REMARK :
Once a belt is dismounted, is not to be remounted, but replaced.
A – crankshaft C – Compressor T – Tensioner pulley.
B – alternator D – Power steeri ng pump – Tensioning checking point.
B
A
A D
TA C
T
T
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 10
ENGINE UNFITTING
Dismo
unt :
- alternator and its belt;
- oil dipper guide;
- induction coil, after its electric co nnector
and spark plugs cables have been disconnected.
ENGINE FITTING
Perform the dismounting operations in the
reverse order.
Tighten the screws and nuts to the required
moment.
Se paration – Unfitting
Di sconnect the electri c connectors and
dismount the engine wiring.
Dismou nt then:
- valve body;
- injection ramp;
-clutch disc and mechanism;
-e ngine flywh eel;
- intake manifold;
- thermal screen and exhaust manifold;
- water inlet pipe;
- thermostat support.
For the veh i cles equi ppe d wi t h a i r
conditioning unit and /or power steeri ng
d ismount additionally:
-driving belt tensioner;
- compressor belt;
- compressor electric connector;
- compressor;
- compressor support and intermedi ary
support.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 11
TIGHTENING MOMENTS (daNm)
Cylinder head cover attachment
screws 1
Distribution belt tightening cam nut 5
W ater pump attachment elements: - M6 1
- M8 2.2
Crankshaft pulley screw 2 plus an angle of 68°±6°
Camshaft gear screw 4.5
Rockers ramp screws 2.3
Engine flywhee l screws
5 - 5.5
Oil pump screws 2.5
Oil pump cover screws 1
Bearing cover screws 2.5 plus an angle of 43°±6°
Cylinder head screws see method described a t page
10-31
Intake manifold attachmen t screws 2.5
Exhaust manifold attachmen t screws 2.5
Spark plugs 2.5 - 3
Lower crankcase screws 1
Rockers adjustment screws 1.5
Oil draining plug 2
Connecting rod cap screws 4.2
Oxygen sensors 4.5
A lternator a ttachment scre ws: - M10 - 135 5
- M 8 - 40 2.1
Clutch mechanism 2
Compressor attachment 4
Compressor support 4
Intermediary support 2
Compressor belt tightening glider 2
D.A. pump attachment 2
D.A. pump support : - M8 2
- M10 4
D.A. pump pulley screws 0.8
RPM sensor 0.8
Starter attachment screws 4.4
Gearbox attachment on engine: - nutsM10 4.4
- screws M10 - 90 4.4
- screws M10 - 35 2.1
Tightening moments
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 12
NO.DE NOM I NAT ION SERVICE DACI A
CODE ITEM NO
1O il plug wrench MOT 1018 1001101 800
2D evice for mounting the camshaft sealing gasket MOT 1127-01 1001112701
3Devic e for mounting crankshaft sealing gasket towards flywheel MOT 1129-01 1001112901
4Devic e for distribution belt tensioning MOT 1135-01 1001113501
5P liers for elastic clips MOT 1202-01 1001120 201
6Su itcase for petrol pressure checking MOT 1311-01 1001131101
7 Connection “J” MOT 1311-04 1001131104
8 Connection “K” MOT 1311-05 1001131105
9D evice for conne ction dismounting MOT 1311-06 1001131106
10 Pliers for valves oil seal ring dismounting MOT 1335 1001133 500
11 Device for checking the belt tensioning MOT 1505 1001150 500
12 Device for pi ston shaft mounting MOT 574-22 1001 0574 22
13 Sector for flywheel fixing MOT 582 1001 0582 00
14 Device for distribution gear blocking MOT 799-01 1001 0799 01
15 Device for mounting the crankshaft sealing gasket towards distribution MOT 550 1001 0550 00
16 Wrench for rockers adjustment MOT 567-01 1001 0567 01
17 Wrench for oil filter MOT 555 1001 0555 00
18 Device for power train sustaining MOT 545 1001 0545 00
19 Device for jackets maintaining MOT 484 1001 0484 00
or
Jackets maintaining clamps MOT 588 1001 0588 00
20 Comparing support MOT 251-01 1001 0251 01
21 Plate for measurement of cylinder jackets over-height MOT 252-01 1001 0252 01
Special tools
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 19
- clearance B (mm):
- minim 0.02
- maxim 0.86.
AT T E N T I O N !
Protect the distribution belt and the accessories belt in order to avoid the water and
cleaning materials splashing on them.
Chara cteristics
OIL PUMP
The oil pump is a gear wheels type.
Oil minimal pressure at 80°C is :
- at idling 1 bar
- at 4000 rpm 3 bar
Dismount the oil pump and check the
gearing clearances.
Check:
- cleara nce A ( mm)
- minim 0.110
- maxim 0.249
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 21
CYLINDER HEA D DISMOUNTING
Drain the oil from the engine.
Dismount :
- wiring from the engine;
- compressor and/or power steering pump ( for vehicles equipped with air conditioning
unit and/or power steering); -compressor support and/or power steering pump support;
- alternator and its belt.
Dismounting – Remounting
Block the engine flywheel by means of the
MOT 582 device .
Dismou nt :
- oil dipper rod support;
- alternator belt tightening clamp;
-cr ankshaft pulley or pulleys ;
- pulley hub;
- distribution belt casings.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 22
Bring the engine at the setting on point, lining up the mark from the crankshaft gear
L with the
fix mark M (the m ark L from the camshaft being in vert ical position as shown in the be llow
drawing). Dismount the nut (0) of the tightening roller, then dismount the distribution belt.
REMARK :
(1) is representing the acting direction of t he tightening roller for distribution belt
tensio ning.
Dismounting – Remounting
vnx.su