Page 97 of 891
IGNITION AND INJECTION
17
17 - 3
ENGI NE BRAND TYPE
E7J - 262 SAGEM RFC 52 LZ
Di stance between electrodes: 0.9 mm
Tightening moment: 2.5 - 3 daNm
Flat seat with gasket
Spark plags
vnx.su
Page 98 of 891
IGNITION AND INJECTION
17
17 - 4
Injection system
CHARACTERISTICS
• Electronic control unit (UCE injection) with 90 pins SIEMENS.
• Sequential multi-poin t injection.
• Controlling one injector each time.
• Static ignition with a double ignition coil.
• Canister purging valve controlled in opening duty cycle.
• Idling regime correction subject to:
- climate maintenance (air conditioning);
- battery voltage.
• Maxima l regime:
- 6200 rot/min for first, second and third speed;
- 6000 rot/min for fourth and fifth speed.
vnx.su
Page 99 of 891
IGNITION AND INJECTION
17
17 - 5
ELEMENTS LOCATION
1. RPM sensor ( tightening moment : 0.8 daNm);
2. Water temperature sensor (tightening moment: 2.5 daNm);
3. Atmospheric pressure sensor;
4. Step-by-step engine for idling adjustment;
6. Air temperature sensor;
7. UCE injection;
8. Choke sensor;
9. Fuse and relays box;
10. Air filter;
11 .D etonation sensor (tightening moment: 2.5 daNm);
12. Oxygen sensor (tightening moment: 4.5 daNm);
13. Ignition coil;
14. Carbon canister with purging valve included;
15. Power steering pressure controller(tightening moment: 1.2 daNm);
16. Air conditioning pressure controller (tightening moment: 0.8 daNm).
Injection system
13 10 11 5 4 6 3 2 1 8 9
14 1 6 15 12 7
vnx.su
Page 100 of 891
IGNITION AND INJECTION
17
17 - 6
7. UC E inj ection;
8. Choke sensor;1. R PM sensor;
2.
Wa ter temperature sensor;
Injection system
8
7
2
1
4
5
63
3. At mospheric pressure sensor;
4.
St ep- by - st ep engin e for idli ng
adjustment
;
5.
Valve position po tentiometer;
6.
A ir temperature sensor;
;
13. Ig nit ion coil;
13
vnx.su
Page 101 of 891
IGNITION AND INJECTION
17
17 - 7
Injection system
In the fuse box located in the engine compartment, the following relays may be identified:
A. Co mpressor relay
B. Engine c ooling fan relay, step I
C. Engine cooling fan relay, step II
D. UCE injection relay, canister-purging valve
E. Fog projectors relay
H. Fuel pump and ignition coil relay
14. C arbon canister with purging valve
included
;
16.
Power steering pressure controller; 12.
Oxygen sensor;
15.
A ir conditioning pressure controller.
1
15
12
1614
vnx.su
Page 102 of 891

IGNITION AND INJECTION
17
17 - 8
Injection system
WATER TEMPERATURE SENSOR
The water temperature sensor ( 1) is sending to UCE injection the information regarding water tempera-
tu re, and another information is sent to the indicator from the instrument panel, which will show the water
tem perature.
In case of an alert regarding the water temperature, UCE injection will control the lightening of
the water temperature indicator from the instrument panel.
Subject to water temperature, UCE injection will control:
- injection system;
- relays for controlling the engine cooling fan.
When setting the contact on, the water temperature indicator located on the instrument panel,
will be lighted for 3 seconds, then it will turn off.
1
1
If after the contact is set off, in the next 2 minutes from engine stopping, the water temperature
is reaching 102 °C, and t hen the injection computer i s control ling t he starting of the e ngine
cooling fan at low speed. When the temperature is lowering at 95°C, the engine cooling fan stopping will be controlled;
its operation must not exceed 10 minutes after engine stopping.
vnx.su
Page 103 of 891

IGNITION AND INJECTION
17
17 - 9
ANTI-STARTING INDICATOR
When setting the contact on, UCE injection is receiving from UCE DECODER a code, whi
ch is compared
with the one previously memorized; if the two codes are matching, then the engine starting is author ized.
After contact setting on, anti-starting indicator which was previously blinking, will light for
three seconds then it will go off, confirming in this way, the key recognizing.
If the key is not good, after setting on the contact, the anti-starting indicator will start blinking
faster and the engine starting will be impossible.
OBSERVATION:
For details regarding the vehicle anti-starting system, see chapter 82 “Anti-starting system”.
AT T E N T I ON!
U CE injection c onnecting or disconnecting to t he vehicle’s wiring i s to be pe rformed
Injection system
only when the engine is stopped and t he contact off.
If the contact is on or the engine is running, do not loosen or disconnect the battery
terminal s. It is forbidden the battery replacement on t he vehicle i f the engine is running
or the contact on. Loosen or rusty contacts at battery terminals and imperfect connections at the
injection system wiring are not allowed. It is forbidden the engine starting with the battery connected to a charging / starting
unit. The battery recharging is t o be pe rformed only aft er disconnecting it from the vehicle
wiring and by means of a c harging unit with 12 V v oltage.
vnx.su
Page 104 of 891

IGNITION AND INJECTION
17
17 - 10
MU LTI-POINT INJE CT ION CHARACT E RISTICS
〈 SIRIUS 32 with 90 pins computer is managing the ignition and the injection.
〈 For diagnostic, CLIP Sagem tester is to be used.
〈 The injection system in use is a sequential multi-point type, injection and ignition phases
controlling being based on the SIRIUS 32 computer program logic, starting from the signal received
from the RPM sensor.
〈The pr esence of the anti-pollution indicator OBD on the instrument panel, that is lighted for
3 seconds when setting the contact on, is specific to the vehicles observing pollution norms EURO
2000. The injection computer of these vehicles is provided with diagnostic system type OBD (“ On
Board Diagnostic).
〈 Idling regime correction is subject to:
-c limate maintenance on/off control (air conditioning)
-e lectrical balance on vehicle, as a result of connecting different electric consumers.
〈 EURO 2000 specific vehicles are provided with two oxygen sensors located in front of the
cata lyst (upstream oxygen sensor) and after catalyst (downstream oxygen sensor).
〈 At EURO 2000 specific vehicles, the fuel supply is performed at constant pressure (3.5 ±
0.2 bar), the pressure controller placed in the fuel tank being provided for this purpose.
Chara cteristics
vnx.su