Page 298 of 891

FRONT AX LES ELEMENTS
31
31 - 7
Brake lining (pads)
REMARK :
In order to maintain the brake efficiency,
the replacement of the brake l ining (pads)
shall be made only in complete kit. Brake pads brand TEXTAR are to be used
as spare parts.
DISMOUNTIN G
Loosen the front wheel attachment screws.
Lift the vehicle by means of a two-column
elevator.
Dismount the front wheel.
Disconnect the wear sensor wire.
Remove: - the safeties of the wedges ( 1);
- the wedges, by sliding them.
D etach the caliper assembly from the fork
together with the flexible hose.
Remove:
- the brake pads from fork seats
(maintaining springs are attached with them);
- the maintaining springs from the brake
pads. REMARK :
It is forbi
dde n t o push the brake
pedal after the c alipers were
dismounted from the fork. If the brake pads are not fully used
but on their friction surface, especially
in the middle pad channel, there are
material traces, it is recommended the
cleaning of these surfaces in order to
avoid the noise when braking. Irregularly we ar of one brake pad or
wear diffe rences between t he inner pad
the outside pad, greater than 10% of the
minimum remaining l ining, impose the
kit replacement.
SPECIAL TOOLS
FR 500 P ushing piston device
1
vnx.su
Page 338 of 891

36
STEERING ASSEMBLY
36 - 5
Noise absorbant bushing
DISMOUNTIN G
Loosen the screws of the right front wheel.
Lift the vehicle by means of a two-column elevator.
Dismount the right front wheel.
Dismou nt :
-steering box casing protection bellows-left steering rod end;
-the right steering connected rod.
Rotate the steering wheel t o the right (complete turn), the rack is withdrawing towards left.
Remove, by means of a screwdriver the used noise absorber bearing.
R EMOU NT I NG
Carefully clean t he rack and the noise absorber bearing seat and grease with special grease
containing MoS2 and then mount the new noise absorber bearing.
Position the pins (A) in their casing seats.
Rotate the steering wheel to the left until t he rack stands out the bearing.
Remount on the rack: - the steering c onnecting rod (safety washer and limiter washer a re t o be obligatory
positioned on the threaded side of the joint body); -protection bellows.
Check and adjust the parallelism, if necessary.
A
A
vnx.su
Page 358 of 891
THE M ECHANICAL ELEMENTS CONTROLS
37
37 - 8
Handbrake control lever
TIGHTENING MOMENTS (daNm)
Attachment screws of the handbrake lever on c entral floor 1.2
DISMOUNTIN G
Disconnect the battery.
Release the hand brake control lever ( released position).
Lift the vehicle by means of a two columns elevator;
Detach the rudder bar fork ( 5) from the end rod (3) by unscrewing the lock nut (1) and
remove the ball-ended washer ( 2).
Remove the secondary cables ends from rudder bar seats.
D etach from clips the rod ( 3) from rudder bar (4)
Lower the vehicle from the elevator and inside the vehicle dismount: - seat;
- carpet attachment clips in the rear side area
- inner attachment of the left/right middle pillars coverings.
M ove the front seats backwards and dismount the a ttachment screw (6) of the handbrake
control on the central floor.
3 4521
vnx.su
Page 359 of 891
THE M ECHANICAL ELEMENTS CONTROLS
37
37 - 9
Move the seats a head and dismount:
- safety belts lower attachment screws;
- attachment screws of the front safety
belts locks and remove them.
Clear the cockpit carpet towards front seats.
Dismount the handbrake control attachment
screw ( 7) on the central floor.
Remove the upper casing of the handbrake
(8).
Han dbrake control lever
Disconnect handbrake contact (9).
Take off the assembly handbrake.
RE MOUNTIN G
Grease the shaft s with UM 185 Li 2M
grease.
Perform the dismounting operations in the
reverse order, taking care to apply a sealant
material layer on the outline of lower casing of
the handbrake lever assembly .
Readjust the handbrake.
vnx.su
Page 360 of 891

THE M ECHANICAL ELEMENTS CONTROLS
37
37 - 10
Handbrake secondary cables
SECONDARY CABLE - REPLACEMENT
DISMOUNTING
Disconnect the battery.
Loosen the rear wheels attachment screws.
Release the ha nd brake control l ever (re-
lease position).
Lift the vehicle by means of a two-column
elevator.
Detach the rudder ba r fork from the end
rod by unscrewing the lock nut (M12 x 1.25)
and remove the ball-ended washer.
Remove the secondary cables ends from
rudder bar seats.
Dismount the two rear wheels.
Dismount the brake drums ( see chapter 33
– Rear axles e leme nts ). Remove the secondary cables stops from
the central floor. Dismount the sheathe stops from the brake
plates. Remove the secondary cables.
REMOU NT I NG
Grease the cable with UM 185 Li 2M
grease
Perform the dismounting operations in the
reverse order.
Adjust the drum clearance ( see chapter 33-
Rear axles elements ”).
Adjust the handbrake control lever stroke.
SPECIAL TOOLS
Ro 441 Wheel drum cover tongs
Fr.600 Hub extractor
TIGHTENING MOMENTS (d aNm)
Wheel attachment screw 7.5
Steering knuckle nut 16.5
vnx.su
Page 519 of 891
75
75 - 1
FRONT SEATS SLIDES GU IDES
Front seat
75 010
TIGHTENING
MOMENTS(daNm)
Fr ont seat attachment screws 2,1
DISMOUNTIN G
Dismount the attachment screws (1) of the
front seat on the side and central cross mem-
ber in the front part.
By acting upon the lever (2) in the arrow
direction, bring the seat in front position and
dismount the attachment screws (3) of the front
seat on the side and re ar c ross-beam in the
rear part.
1 2 3
4
5
Release the front chair.
Remove the headrests by simultaneously
pushing of the buttons (4) attached on the head-
rests sleeves.
R EMOU NT I NG
Perform the dismounting operations in the
reverse order.
The front seat attachment screws are to be
tighten to the required moment of 2,1 daNm.
ADJUSTMENTS
The front seats, have two possibilities of ad-
justment:
- front or rear longitudinal movement,
w hich can be performed by lever’s operation
(2); - seat back reclining up to the horizontal
position, by rotating the round button (5).
vnx.su