2020 MITSUBISHI OUTLANDER PHEV Owner's Manual (in English)

CAUT,ONzBe sure to insert the quick charge connector
straight into the quick charge port right up to
the base.
Failure to do so may result in the drive bat- tery not charging or could cause damage to the charging equipment.
z During quick charging, the quick charge
connector cannot be removed because it is locked. Do not touch or remove the quick
charge connector during charging. Doing so,
the quick charge connector might be dam- aged. If you want to stop the quick charging
on the way, stop the charging according to
the procedures of a quick charger, and re-
move the quick charge connector after con-
firming the charging is stopped.NOTEz There is a hole on the charge port for water
drainage. If this hole is blocked and watergets trapped in the charge port, do not
charge. Contact a MITSUBISHI MOTORS
Authorized Service Point.
z If the charge port is frozen, melt the ice us-
ing a hair drier. Forcing the charge connector to connect while frozen could result in mal-
function.
5. Connect the quick charge connector in
the quick charge port to begin charging.
For connecting and disconnecting, fol- low the instruction manual for each
quick charger.
6. Make sure that the charging indicator (E)
on the instrument cluster is illuminated.
If the charging indicator is not illumina-
ted, charging is not started.
Follow the manual of each quick charg- er.
NOTEz When the quick charge connector is connec-
ted to the charge port, the charging indicatoris blinking. When charging is started, the charging indicator is illuminated.
z If you want to confirm the drive battery level
during charging, open one of the doors or operate the multi information display switch,
the drive battery level display (F) appears on the information screen in the multi informa-tion display.
Although the predicted charging time dis-
play (G) appears, the charging time for the quick charging is approximately 30 minutes and displayed “--:--” in the screen and you
cannot confirm the remaining charging time.
z Operation noise may be heard from the vehi-
cle body during quick charging.
This noise comes from the operation of the drive battery cooling system, and it is not a malfunction.
z Since the drive battery cooling system uses
cool air of the air conditioning, the air condi-tioning is automatically operated.
After quick charging, if the area under the vehicle is wet, transparent and loose, it is de-
humidified water from the air conditioning and not a malfunction.
z When an electrical component is used during
charging, the charging time may become
longer.
7. Charging is complete when the charging
indicator turns off.
Quick charging (charging method with quick charger)
3-192**(20(1Charging3

Disconnect the quick charge connectoraccording to the manual of the quick
charger.CAUT,ONz As the quick charge connector is heavier in
comparison to the normal charge connector, allowing it to drop could cause damage to
the vehicle or charge connector or personal injury. When removing the connector, besure to pull it out straight and as carefully as
possible.
z Do not leave the quick charge connector
connected to the quick charge port after charging.
Doing so, someone might stumble and it
could cause an injury or the quick charging connection might be damaged by playing it.NOTEz Although it is possible to start the electric
motor unit if quick charging has not finishednormally, the charging indicator is continu-
ously blinking. In such a situation, perform
quick charging again and finish it normally or contact a MITSUBISHI MOTORS Au-
thorized Service Point.
8. Close the inner lid and press the rear of
the charging lid until it clicks to close it.
:ARN,NGz After charging, be sure to close the inner
lid and the quick charging lid completely.
Be careful that water or dust does not en-
ter in the quick charge port, inner lid and
quick charge connector.
Entry of water or dust could cause fire, electric shock or short circuit.
z After charging, be sure to disconnect the
charge connector from the charge port.
If the charge connector is only partially
engaged and the connector latch is un-
locked, you could put the operation mode of the power switch in ON and the vehicle
could start moving. It could lead to an un- expected accident.NOTEz If the operation mode of the power switch is
put in ON with the quick charge connector
connected to the quick charge port, the plu-
gin hybrid EV system cannot be started.
Be sure to disconnect the quick charge con- nector before start.
z Charging may be completed before full
charge. This is a control for efficient charge
and not a malfunction.
To achieve full charge, repeat charging from Step 5 again.NOTEz Make sure that the inner lid is completely
closed.
If the charging lid is forcibly closed without completely closing inner lid, the hinge on
the inner lid may be broken.
z While the charging lid is open, if the doors
and tailgate are locked with the central door
lock, the keyless entry system or the keyless
operation system, the charging lid will lock when the charging lid is closed.
z When the operation mode is switched to ON
while the charging lid is not completely closed, a warning may be displayed on the
information display of the multi information
display.
Refer to “Warning display list” on page 6-25.MITSUBISHI Remote
Control*
The MITSUBISHI Remote Control allows to
operate the vehicle within the communication
range of the wireless LAN device (whichconforms to IEEE 802.11b and supports iOS
or Android). The following operations are available.
MITSUBISHI Remote Control*
3-202**(20(1Charging3

NOTEzThe communication distance differs depend-
ing on the wireless LAN device, due to this
the communication may go down.
1- Wireless LAN device
2- Antenna
z Charging timer
If you specify the charge start and/or
stop time with the normal charge cable connected, charging is started and/orstopped at that time.
z Remote Climate Control
By setting the remote climate control to operate at a predetermined time, cabin comfort can be improved or visibility
can be ensured (defrosting/demisting) before getting in the vehicle.
z Customize (function setting change)
The function setting of the keyless oper-
ation system, outside rear-view mirror, operation mode of the power switch, air
conditioning, lamps and windscreen
wipers can be changed by MITSUBISHI
Remote Control.NOTEz The electric heater is required to activate the
reservation functions of heater, defroster anddemister.
z In a vehicle equipped with the Smartphone-
link Display Audio (SDA) ot the Smart-
phone-link Display Audio (SDA) navigation
system, it is possible to change the setting by means of screen operations.
Refer to the separate owner’s manual for de- tails.
z If you want to quickly start normal charging
even when the charging timer is already set,
you can cancel the charging timer and start the normal charging by the following meth- ods.
[How to temporarily cancel the charging
timer@
You can temporarily cancel the charging timer by the following methods.
In addition, the predetermined charging tim- er settings will automatically return after the
charging timer is turned on again or the op- eration mode of the power switch is put in
ON.NOTE

Devices that support wireless LAN are re-
quired to communicate with the vehicle using
the MITSUBISHI Remote Control. Also, an
SSID* (A) and password (B) are required to
connect a wireless LAN device to the vehi-
cle. The SSID and password are described in the registration information card (C) that is
attached to the key at the time of your pur- chase of the vehicle.* The SSID is the identifier of an accesspoint for IEEE 802.11 series wireless LAN. It
is displayed on wireless LAN devices.NOTEz When you transfer ownership of the vehicle
to another person, transfer the registrationinformation card with the vehicle.
For the function and the operation method of the
MITSUBISHI Remote Control, please visit the
MITSUBISHI MOTORS’ Web site (in English
only):
https://www.mitsubishi-motors.com/en/products/
outlanderBphev2/app/remote/
z If you need further information, please con-
tact a MITSUBISHI MOTORS Authorized
Service Point.
:ARN,NGz Do not use the
MITSUBISHI Remote
Control if children, persons in need of care, pets, etc. are in the vehicle. Even if
the remote climate control is used, the cabin may become hot or cold due to some
reasons such as automatic stop of the sys-
tem. The cabin temperature may quickly rise in sunshine, which poses a risk of heat
stroke and dehydration. In cold weather,
on the other hand, the cabin temperature may quickly drop. Either of which could lead to death in the worst case.
In addition, children can activate switches and controls, resulting in injury or a fatal accident.
z The cooling fan in the engine compart-
ment may operate automatically when
charging or when operating air condition- er. Do not bring your hand close to the
cooling fan during charging.CAUT,ONz Do not use a car cover except for the
MITSUBISHI MOTORS GENUINE car
cover, when using the charging timer or the remote climate control.
MITSUBISHI Remote Control*
3-222**(20(1Charging3

NOTEzWhen the ownership of the vehicle is trans-
ferred to or from others, it is necessary to in-
itialize the registration of the MITSUBISHI
Remote Control.
For the registration initialization procedure, please visit our web site.
https://www.mitsubishi-motors.com/en/prod-
ucts/outlanderBphev2/app/remote/
z Keep the following points in mind when us-
ing a wireless LAN device:

NOTEzIf the remote climate control is started dur-
ing charging, the time until full charge may extend or the charging rate may decrease.
z When the remaining quantity of the drive
battery is decreased, the remote climate con- trol does not operate or it may stop on theway.
z When the auxiliary battery is removed, the
timer control of the MITSUBISHI Remote
Control is reset and each function of the MITSUBISHI Remote Control cannot be
used. Also the drive battery cannot be
warmed up.
Communicate the wireless LAN device and your vehicle again.How to use an electric
device during charging
If you turn the operation mode of the power switch to “ON” during normal charging,
quick charging, V2H charging, V2H power supply, you can use the air conditioner, car
navigation system, audio equipment and so
on.
V2H (Vehicle to Home)
The vehicle power can be used as a house-
hold power supply source. Bidirectionalcharging of the vehicle or the home is carried
out by using the quick charge connector of
CHAdeMO standard which is the same as quick charging. “V2H charging” will charge
the vehicle from the V2H main unit. “V2H
power supply” supplies power from the vehi- cle to the home via the V2H main unit.
For details of V2H, please confirm with the
PHEV to HOME sales catalogue or the in- struction manual that is issued by the V2H
maker or consult the V2H maker.
:ARN,NGz Do not get in the vehicle if the persons
have electro-medical apparatus such as implantable cardiac pacemaker or im-plantable cardioverter-defibrillator, when
using the air-conditioner during charging.
It may affect the operation of electro- medical apparatus.:ARN,NGz Do not leave children and people who
need nursing care and pets etc. inside thevehicle.
The inside of the vehicle may become hot or cold for reasons such as automatic sys-
tem shutdown.
Also, when the outside air temperature is low, the temperature inside the vehicle
may fall rapidly. In the worst case, there is a danger of death.
Also, since the wiper and the electric
parking brake can be operated, an error
in operation may lead to unexpected acci- dents.
z Please check the surroundings before us-
ing.
z Do not move the selector lever, the vehicle
may move unintentionally.NOTEz When using electrical devices during charg-
ing, the following cases may occur, since thecharging to the drive battery is restricted.

NOTE

zWhen the outside air temperature is low
and the following warning display ap- pears.
z When charging is completed.
z When the normal charge connector is
disconnected.
z When the charging stop operation is per-
formed by the quick charger.
z When the quick charging time has
passed 60 minutes.
z When the stop condition (charging
amount/charging time) on the quick charger is satisfied.
z When charging stops due to an electrical
power outage.
z When charging stops due to a failure.
z When operating the selector lever to the
“N” (NEUTRAL) position. (charging al-
so stops)
NOTEz Even when the operation mode automatical-
ly puts off, air conditioners, car navigation systems, audio equipment, etc. will stop.
Also, the vehicle status will be the same as putting the operation mode OFF (for exam-
ple: the lights go off, the room lamp is illu- minated or the electric mirrors are retracted).Automatic stop of the air con-
ditioner
In the following cases, the air conditioner au- tomatically stops. When the air conditioner stops, the air conditioner control panel turns
off.
z When the remaining amount of the drive
battery becomes low and the following
warning display appears.
Refer to “Warning display list” on page 6-25.
z When the temperature of the drive bat-
tery becomes extremely low and the fol-
lowing warning display appears.
Refer to “Warning display list” on page 6-25.
NOTEz To use the air conditioner again after the air
conditioner automatically stops, press the
power switch to turn the operation mode
OFF with the following message appeared, then press the power switch again to turn ON the operation mode of the power switch
so as to use the air conditioner.
Refer to “Warning display list” on page 6-25.
How to use an electric device during charging
3-262**(20(1Charging3