2020 MITSUBISHI OUTLANDER PHEV Owner's Manual (in English)

CategoryCharge portCharge connectorCharging Source
Charging timewith fully dis-
charged battery* 3Refer-
ence
Quick charging
(charging method
with quick charger)
Right rear side of vehiclePublic charging stations where available
Approximately 25minutes for 80 % charge
p. 3-17
*1: Optional equipment
*2 : EVSE = Electric Vehicle Supply Equipment
*3 : Use this time as a guide because the rated AC voltage and the rated current value may differ from country to country.
Also, the charging time will vary depending on the condition of the drive battery, air temperature, electric power consumption of electrical devi-
ces during charging and condition of the power source (such as specifications of the quick charger).
*4 : When using a EVSE to which charging cable is not attached, use a Mode 3 charging cable for OUTLANDER PHEV (Type 2 to 1) -available
separately. For details, please consult a MITSUBISHI MOTORS Authorized Service Point.
Charging
3-032**(20(1Charging3

NOTEzThe drive battery can be charged to nearly full using the battery charge mode switch.
Refer to “SAVE/CHARGE mode switch” on page 7-27. Refer to “Battery save mode” on page 7-28.

Battery
There are two types of batteries installed in
your vehicle: a drive battery for operating the
motor (electric motor unit) and air condition- ing as well as an auxiliary battery for starting
the Plug-in Hybrid EV system and operating the lamps, wipers, etc.
This chapter explains charging of the drive battery.NOTEz The auxiliary battery is automatically charg-
ed while the ready indicator is illuminated orduring charge for the drive battery.
Refer to “Ready indicator” on page 6-55.
z If the auxiliary battery is flat, the Plug-in
Hybrid EV system cannot be started.
Refer to “Emergency starting” on page
9-02.Basic knowledge for
charging
There are two types of charging: normal
charging and quick charging.
Normal charging is performed through the on board charger using rated AC 220-240V out-
let as the power source
The rated AC voltage may differ from coun-
try to country.
Battery
3-042**(20(1Charging3

:ARN,NGzTo reduce the risk of electric shock or fire
due to electric leak, always use an earthed
outlet protected by a residual current de-
tector, rated for amperage equal to or
greater than the value specified by MITSUBISHI MOTORS , and that is con-
nected to a dedicated branch circuit. If the circuit is shared, and another electri-cal device is being used at the same time
as the vehicle is charging, the circuit may heat abnormally, the breaker may trip
and the circuit may cause adverse inter-
ference on the household electrical appli-
ances such as TVs and audio systems.
z It is possible to charge even in rain or
snow. However, be sure to pay attention to the following:

NOTE

EV charging cable*
Your vehicle is equipped with an EV charging cable that consists of a cable (A), control box (B), EV charging cable plug (C), and normal charge
connector (D).E-Manual stop buttonG ()-POWER indicatorF-Stop indicatorH ()-FAULT indicator I ()-CHARGING indicator
To stop charging, simply press manual stop button (E) and stop indicator (F) is illuminated. Re-connect the EV charging cable plug (C) to charge
again.
POWER (G), FAULT (H) and CHARGING (I) indicators located on the control box will illuminate/blink in response to the following conditions:
EV charging cable*
3-072**(20(1Charging3Indicator (LED) and buttonCB
A
D G H I
E F

: Illuminates : Blinking : Not illuminatesPOWERFAULTCHARGINGOperating conditionEvery time the charging cable plug (C) is connected to an outlet, all indication lamps illu-minate for 0.5 seconds.After initial processing is completed, when the normal charge connector is not connected tothe charge port, or the normal charge connector is connected to the charge port but chargingis not being performed.While the drive battery is being charged.When charging is completed.POWERFAULTCHARGINGAbnormal operating condition and corrective actionWhen an electric leakage occurs or the EV charging cable malfunctionsStop using the EV charging cable immediately and contact a MITSUBISHI MOTORS Au-
thorized Service Point.When the EV charging cable malfunctions
Stop using the EV charging cable immediately and contact a MITSUBISHI MOTORS Au-
thorized Service Point.If the control box indication lamp does not illuminate after connecting the charging cable plug to the outlet, check the circuit breaker for the outlet. If the breaker has tripped, the cir-cuit may not be suitable for use with EV charging cable. You should have a licensed electri-cian inspect and repair the electrical circuit. If the breaker is not tripped, stop using the EV
charging cable and contact a MITSUBISHI MOTORS Authorized Service Point.
EV charging cable*
3-082**(20(1Charging3

:ARN,NGzIf the POWER or CHARGING indicator does not illuminates or the FAULT indicator blinks or illuminates during normal charging, please contact
a MITSUBISHI MOTORS Authorized Service Point.
z Do not charge when the EV charging cable is coiled up.
The cable may be heated abnormally and resulting in fire.
z Do not alter or disassemble the EV charging cable. Doing so could cause fire, an electric shock or injury.
z Be sure to install the cap to the normal charge connector and store the EV charging cable in a place where the cable is not exposed to water or dust.
Entry of foreign matter such as water or dust in the metal terminal of the normal charge connector or charging cable plug may cause a fire or
malfunction.
z Never force the connection if the EV charging cable or connector shows damage or is not easily connected due to foreign material entering the
connector or the outlet. And never use an outlet that is worn, damaged, or will not hold the plug firmly. Doing so could cause fire, an electric shock,
or short circuit.
z Pay attention to the following for handling the EV charging cable.
Damage to the cable could cause fire, an electric shock, or short circuit.

Handling and storing the con-trol boxCAUT,ONz While charging, prevent damage to the con-
trol box by attaching a rope as shown in the following illustration.NOTEz Use a hook with a load capacity over 4 kg.
z Check that the rope and hook have no dam-
age and are not loose before use.HookRope
Cleaning the EV charging cable
1. Lightly wipe these off with a soft cloth
soaked in a mild soap and water solu- tion.
2. Wipe off all the detergent with a soft
cloth dipped in fresh water and thor- oughly wrung out.
3. Wipe all moisture off and dry in a sha-
ded, well-ventilated area.:ARN,NGz When cleaning, be sure to remove the
charging cable plug and the normal charge connector from the outlet. Do not connect or disconnect the plug and the
connector with wet hands. Doing so could cause an electric shock.
z Do not expose the metal terminal of the
normal charge connector or the chargingcable plug to water or neutral detergent.
Using in wet with water could cause a fire or an electric shock.CAUT,ONz Never use benzine, petrol, or other organic
solvents, or acid or alkaline solvents. Doing
so could cause deformation, discolour, or malfunction. Also, these substances may be
present in various cleaners, so check careful- ly before using.Normal charging (charging
method with rated AC220-240V outlet):ARN,NGz For safety, do not allow children or people
who are not familiar with charging to charge for themselves. Also, do not use
the normal charge connector within reach
of children.
z Persons who use electro-medical appara-
tus such as implantable cardiac pacemak-
er or implantable cardioverter defibrilla- tor must check effect from charging with the manufacturer of electro-medical ap-
paratus. Electro-medical apparatus oper- ations could be affected by charging.
z If you use electro-medical apparatus such
as implantable cardiac pacemaker or im- plantable cardioverter-defibrillator, be
careful the following precautions.