2013 Lancia Voyager Owner handbook (in English)

CAUTION!
Do not use chemical flushes in your
transmission as the chemicals can
damage your transmission compo-
nents. Such damage is not covered
by the New Vehicle Limited War-
ranty.
Fluid Level Check
The fluid level is preset at the factory
and does not require adjustment un-
der normal operating conditions.
Routine fluid level checks are not re-
quired, therefore the transmission has
no dipstick. Your authorized dealer
can check your transmission fluid
level using a special service dipstick.
If you notice fluid leakage or trans-
mission malfunction, visit your au-
thorized dealer immediately to have
the transmission fluid level checked.
Operating the vehicle with an im-
proper fluid level can cause severe
transmission damage.
CAUTION!
If a transmission fluid leak occurs,
visit your authorized dealer imme-
diately. Severe transmission dam-
age may occur. Your authorized
dealer has the proper tools to adjust
the fluid level accurately.
Fluid And Filter Changes
Refer to the “Maintenance Schedule”
for the proper maintenance intervals.
In addition, change the fluid and filter
if the transmission is disassembled for
any reason.CAUTION!
Car maintenance should be done at
a LANCIA Dealership. For routine
and minor maintenance operations
you wish to carry out yourself, we
do recommend you have the proper
equipment, genuine LANCIA spare
parts and the necessary fluids; do
not however carry out these opera-
tions if you have no experience. APPEARANCE CARE AND
PROTECTION FROM
CORROSION
Protection Of Body And Paint
From Corrosion
Vehicle body care requirements vary
according to geographic locations and
usage. Chemicals that make roads
passable in snow and ice and those
that are sprayed on trees and road
surfaces during other seasons are
highly corrosive to the metal in your
vehicle. Outside parking, which ex-
poses your vehicle to airborne con-
taminants, road surfaces on which the
vehicle is operated, extreme hot or
cold weather and other extreme con-
ditions will have an adverse effect on
paint, metal trim, and underbody
protection.
The following maintenance recom-
mendations will enable you to obtain
maximum benefit from the corrosion
resistance built into your vehicle.
315

What Causes Corrosion?
Corrosion is the result of deterioration
or removal of paint and protective
coatings from your vehicle.
The most common causes are:
 Road salt, dirt and moisture accu-mulation.
 Stone and gravel impact.
 Insects, tree sap and tar.
 Salt in the air near seacoast localities.
 Atmospheric fallout/industrial pol- lutants.
Washing
 Wash your vehicle regularly. Al- ways wash your vehicle in the shade
using a mild car wash soap, and
rinse the panels completely with
clear water.
 Use a high quality cleaner wax to remove road film, stains and to pro-
tect your paint finish. Take care
never to scratch the paint.  Avoid using abrasive compounds
and power buffing that may dimin-
ish the gloss or thin out the paint
finish.
CAUTION!
Do not use abrasive or strong clean-
ing materials such as steel wool or
scouring powder that will scratch
metal and painted surfaces.
Special Care
 If you drive on salted or dusty roads or if you drive near the ocean, hose
off the undercarriage at least once a
month.
 It is important that the drain holes in the lower edges of the doors and
rocker panels be kept clear and
open.
 If you detect any stone chips or scratches in the paint, touch them
up immediately. The cost of such
repairs is considered the responsi-
bility of the owner.  If your vehicle is damaged due to an
accident or similar cause which de-
stroys the paint and protective
coating, have your vehicle repaired
as soon as possible. The cost of such
repairs is considered the responsi-
bility of the owner.
 If you carry special cargo such as chemicals, fertilizers, de-icer salt,
etc., be sure that such materials are
well packaged and sealed.
 If a lot of driving is done on gravel roads, consider mud or stone
shields behind each wheel.
 Use Touch Up Paint or equivalent on scratches as soon as possible.
Your authorized dealer has touch
up paint to match the color of your
vehicle.
Wheel And Wheel Trim Care
All wheels and wheel trim, especially
aluminum and chrome plated wheels,
should be cleaned regularly with a
mild soap and water to prevent corro-
sion.
316

CAUTION!
Do not use scouring pads, steel
wool, a bristle brush, or metal pol-
ishes. Do not use oven cleaner.
These products may damage the
wheel’s protective finish. Avoid au-
tomatic car washes that use acidic
solutions or harsh brushes that may
damage the wheel’s protective fin-
ish. Use only the approved wheel
cleaners or equivalent.
Stain Repel Fabric Cleaning
Procedure (for versions/markets,
where provided)
Stain Repel seats may be cleaned in
the following manner:
 Remove as much of the stain as possible by blotting with a clean,
dry towel.
 Blot any remaining stain with a clean, damp towel.
 For tough stains, apply a mild soap solution to a clean, damp cloth and
remove the stain. Use a fresh, damp
towel to remove soap residue.  For grease stains, apply a high
quality cleaner to a clean, damp
cloth and remove the stain. Use a
fresh, damp towel to remove soap
residue.
 Do not use any harsh solvents or any other form of protectants on
Stain Repel products.
Interior Care
Instrument Panel Surfaces
The instrument panel cover has a low
glare surface, which minimizes reflec-
tions in the windshield. Do not use
protectants or other products which
may cause undesirable reflections.
Use soap and warm water to restore
the low glare surface.
Cleaning Leather Upholstery
Your leather upholstery can be best
preserved by regular cleaning with a
damp soft cloth. Small particles of
dirt can act as an abrasive and dam-
age the leather upholstery and should
be removed promptly with a damp
cloth. Care should be taken to avoid soaking your leather upholstery with
any liquid. Please do not use polishes,
oils, cleaning fluids, solvents, deter-
gents, or ammonia-based cleaners to
clean your leather upholstery. Appli-
cation of a leather conditioner is not
required to maintain the original con-
dition.
WARNING!
Do not use volatile solvents for
cleaning purposes. Many are poten-
tially flammable, and if used in
closed areas they may cause respi-
ratory harm.
Cleaning Headlights
Your vehicle is equipped with plastic
headlights and fog lights (if
equipped) that are lighter and less
susceptible to stone breakage than
glass headlights.
Plastic is not as scratch resistant as
glass and therefore different lens
cleaning procedures must be fol-
lowed.
317

To minimize the possibility of scratch-
ing the lenses and reducing light out-
put, avoid wiping with a dry cloth. To
remove road dirt, wash with a mild
soap solution followed by rinsing.
Do not use abrasive cleaning compo-
nents, solvents, steel wool or other
aggressive material to clean the
lenses.
Glass Surfaces
All glass surfaces should be cleaned
on a regular basis with any commer-
cial household-type glass cleaner.
Never use an abrasive type cleaner.
Use caution when cleaning the inside
rear window equipped with electric
defrosters or the right rear quarter
window equipped with the radio an-
tenna. Do not use scrapers or other
sharp instrument that may scratch
the elements.
When cleaning the rear view mirror,
spray cleaner on the towel or rag that
you are using. Do not spray cleaner
directly on the mirror.Cleaning Plastic Instrument
Cluster Lenses
The lenses in front of the instruments
in this vehicle are molded in clear
plastic. When cleaning the lenses,
care must be taken to avoid scratch-
ing the plastic.
1. Clean with a wet soft rag. A mild
soap solution may be used, but do not
use high alcohol content or abrasive
cleaners. If soap is used, wipe clean
with a clean damp rag.
2. Dry with a soft cloth.
Seat Belt Maintenance
Do not bleach, dye or clean the belts
with chemical solvents or abrasive
cleaners. This will weaken the fabric.
Sun damage can also weaken the fab-
ric.
If the belts need cleaning, use a mild
soap solution or lukewarm water. Do
not remove the belts from the car to
wash them. Dry with a soft cloth.
Replace the belts if they appear frayed
or worn or if the buckles do not work
properly.CLEANING THE
INSTRUMENT PANEL
CUPHOLDERS
Removal
Pull the flexible liner from the cup-
holder drawer starting at one edge to
ease removal.
Cleaning
The liner is top shelf dishwasher safe,
or you may follow the cleaning proce-
dure below.
Soak the liner in a mixture of medium
hot tap water and one teaspoon of
mild liquid dish soap. Let soak for
approximately 30 minutes. After 30
minutes, pull the liner from the water
and dip it back into the water about
six times. This will loosen any remain-
ing debris. Rinse the liner thoroughly
under warm running water. Shake the
excess water from the liner and dry
the outer surfaces with a clean soft
cloth.
318

Installation
Place the liner into the cupholder
drawer and press the liner into place
so that the retention tabs seat into the
corresponding openings in the
drawer.
FUSES
TOTALLY INTEGRATED
POWER MODULE
The Totally Integrated Power Module
is located in the engine compartment
near the battery. Refer to the appli-
cable “Engine Compartment” illus-
tration in this section. This center
contains cartridge fuses and mini-
fuses. A label that identifies each
component may be printed or em-
bossed on the inside of the cover.
CAUTION!
 When installing the Totally Inte-grated Power Module cover, it is
important to ensure the cover is
properly positioned and fully
latched. Failure to do so may al-
low water to get into the Inte-
grated Power Module, and possi-
bly result in a electrical system
failure.
(Continued)
CAUTION!(Continued)
 When replacing a blown fuse, it is important to use only a fuse hav-
ing the correct amperage rating.
The use of a fuse with a rating
other than indicated may result in
a dangerous electrical system
overload. If a properly rated fuse
continues to blow, it indicates a
problem in the circuit that must
be corrected.
The numbers inside the TIPM cover
correspond to the following table.
Totally Integrated Power Module
319

FUSES/TIPM
Cavity Cartridge Fuse Mini-Fuse Description
J1 40 Amp Green — Power Folding Seat
J2 30 Amp Pink — Power Liftgate Module
J3 30 Amp Pink — Rear Door Module (RR Door Node)
J4 25 Amp Natural — Driver Door Node
J5 25 Amp Natural — Passenger Door Node
J6 40 Amp Green — Antilock Brakes Pump/Stability Control System
J7 30 Amp Pink — Antilock Brakes Valve/Stability Control System
J8 40 Amp Green — Power Memory Seat (for versions/markets, where provided)
J9 40 Amp Green — Partial Zero Emissions Vehicle Motor/Flex Fuel
J10 30 Amp Pink — Headlamp Wash Relay/Manifold Tuning Valve
J11 30 Amp Pink — Power Sliding Door Module/Anti–Theft Module Relay Lock
Feed
J12 30 Amp Pink Rear Blower Motor/ RAD Fan
J13 60 Amp Yellow — Ignition Off Draw (IOD) – Main
J14 40 Amp Green — Rear Window Defogger
J15 40 Amp Green — Front Blower
J17 40 Amp Green — Starter Solenoid
J18 20 Amp Blue — Powertrain Control Module Trans Range
J19 60 Amp Yellow — Radiator Fan
J20 30 Amp Pink — Front Wiper LO/HI
J21 20 Amp Blue — Front/Rear Washer
J22 25 Amp Natural — Sunroof Module
M1 — 15 Amp Blue Rear Center Brake Lamp/Brake Switch
M2 — 20 Amp Yellow Trailer Lighting/Fog Lamps
M3 — 20 Amp Yellow Front/Rear Axle Locker/Vacuum Pump Motor
M4 — 10 Amp Red Trailer Tow
M5 — 25 Amp Natural Inverter
320

FUSES/TIPM
Cavity Cartridge Fuse Mini-Fuse Description
M6 — 20 Amp Yellow Power Outlet #1 (ACC), Rain Sensor
M7 — 20 Amp Yellow Power Outlet #2 (BATT/ACC SELECT)
M8 — 20 Amp Yellow Front Heated Seat (for versions/markets, where provided)
M9 — 20 Amp Yellow Rear Heated Seat (for versions/markets, where provided)
M10 — 15 Amp Blue Ignition Off Draw — Video System, Satellite Radio, DVD,
Hands-Free Module, Universal Garage Door Opener, Vanity
Lamp, Streaming Video Module
M11 — 10 Amp Red Ignition Off Draw – Climate Control System
M12 — 30 Amp Green Amplifier (AMP)/Radio
M13 — 20 Amp Yellow Ignition Off Draw— Instrument Cluster, SIREN, Clock Module,
Multi-Function Control Switch/ITM
M14 — 20 Amp Yellow Spare Fuse
M15 — 20 Amp Yellow Rear View Mirror, Instrument Cluster, Multi-Function Control
Switch, Tire Pressure Monitor, Glow Plug Module – Export Die-
sel Only, Assy-Shifter (Hall Effect), Acoustic Noise Cancellation
M16 — 10 Amp Red Airbag Module/Occupant Classification Module
M17 — 15 Amp Blue Left Tail/License/Park Lamp, Running Lamps
M18 — 15 Amp Blue Right Tail/Park/Run Lamp
M19 — 25 Amp Natural Automatic Shutdown #1 and #2
M20 — 15 Amp Blue Instrument Cluster Interior Light, Switch Bank, Steering Col-
umn Module, Switch Steering Wheel
M21 — 20 Amp Yellow Automatic Shutdown #3
M22 — 10 Amp Red Right Horn (HI/LOW)
M23 — 10 Amp Red Left Horn (HI/LOW)
M24 — 25 Amp Natural Rear Wiper
M25 — 20 Amp Yellow Fuel Pump, Diesel Lift Pump – Export Only
M26 — 10 Amp Red Power Mirror Switch, Driver Window Switch
321

FUSES/TIPM
Cavity Cartridge Fuse Mini-Fuse Description
M27 — 10 Amp Red Ignition Switch, Wireless Control Module, Keyless Entry Mod-
ule, Steering Column Lock
M28 — 10 Amp Red Powertrain Control Module, Transmission Feed, Transmission
Control Module
M29 — 10 Amp Red Occupant Classification Module
M30 — 15 Amp Blue Rear Wiper Module, Power Folding Mirror, J1962 Diagnostic
Feed
M31 — 20 Amp Yellow Back-Up Lamps
M32 — 10 Amp Red Airbag Module, TT EUROPE
M33 — 10 Amp Red Powertrain Control Module, Transmission Control Module
M34 — 10 Amp Red Park Assist, Heater Climate Control System Module, Headlamp
Wash, Compass , IR Sensor, Rear Camera, Lamp Door FT Drv/
Pass, Lamp Flashlight, AHLM, Relay Diesel Cabin Heater, Rad
Fan Diesel
M35 — 10 Amp Red Heated Mirrors
M36 — 20 Amp Yellow Power Outlet #3
M37 — 10 Amp Red Antilock Brakes, Stability Control System, Stop Lamp Switch,
Fuel Pump Rly Hi Control
M38 — 25 Amp Natural Door Lock/Unlock Motors, Liftgate Lock/Unlock Motors
The heated mirrors, lower instrument
panel power outlet and removable
floor console, when in the front posi-
tion are fused with self-resetting fuses
that are only serviceable by an autho-
rized dealer. The power seats are
fused by a 30 Amp circuit breaker
located under the driver's seat. The power windows are fused by a 25
Amp circuit breaker located under the
instrument panel near the steering
column. If you experience temporary
or permanent loss of these systems,
see your authorized dealer for service.
322