2006 LAND ROVER FRELANDER 2 window

Apply acti vat or over t he old sealant on t he wi nds hiel d glas s andall ow t o cure.4.
Fit a pre-cut nozzl e t o the sealer cart ri dge, remove the lid,s hake out t he crys tal s and fi t the cartridge t o t he appl icatorgun.Modify t he nozzle to achieve a bead s ecti on in the s hape of aright angl e t ri angle wit h a bas e of 8 mm and a verti cal heightof 12 mm.
5.
Apply a cont inuous bead of s ealant to thewi nds hiel d glas s.
6.
CAUTION: Make s ure the heated front s creen foil electrical connect ors are t ucked underneat h t he body plenum panel.This wi ll avoid contact wit h t he winds creen wi per arm l inkage.
W it h ass i st ance, i ns t all the window glas s .Light ly pres s t he wi ndow glas s to seat t he s eal er.Secure t he winds hield gl ass in pos it ion us ing tape.Connect t he heat ed front s creen electrical connect ors , ifi ns t alled.
7.
Tes t the s ealer for l eaks , appl y addit ional s ealer i f necess ary.If water is used, all ow s eal er to dry before t es t ing. Spraywat er around the gl as s and check for leaks . Mark any areat hat l eaks . Dry the gl ass and sealer t hen appl y addit ionals ealer.
8.
Inst all t he plenum chamber panel.
Refer t o: Plenum Chamber (412-01 Cl imat e Control, Removal andInst all at ion).
9.
Inst all t he A-pi llar t ri m panels .
Refer t o: A-Pil lar Tri m Panel (501-05 Int erior Trim andOrnament ati on, Removal and Ins tal lat ion).
10.
Inst all t he int erior mi rror.
Refer t o: Int erior Rear View Mirror (501-09 Rear Vi ew Mi rrors ,Removal and Ins tall ati on).
11.

Publi s hed: 11-May-2011
Glass, Frames and Mechanisms - Front Door Window Regulator and Motor
Removal and Inst all ati on
Special T ool(s) 501-114
Releas e Lever, Door Glas s
Removal
• NOTE: If pos s ible, l ower t he wi ndow glas s by approximat el y one t hird of it s travel .
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1.
Remove t he front door s peaker.
Refer t o: Front Door Speaker (415-01 Informat ion and Ent ert ainment
Syst em, Removal and Ins tall ati on).
2. Carefully remove t he outer wais t s eal.
3. Releas e t he door wi ndow glas s from the wi ndow li ft
mechani s m. Rais e t he glas s and s ecure it t o t he t op of
t he door frame.
Speci al Tool (s ): 501-114 4.

Remove t he glas s guide channel.5.
Remove t he front door cont rol module.6.
Remove t he window mot or and regulat or as s embly.7.
Installation
Inst all t he window mot or and regulat or as s embly. Tighten the nut sand t he bolt s.1.

T orque:
10 Nm Inst all t he door control modul e.
2.
Inst all t he glas s guide channel and li ning. Ti ghten t he bolt .
T orque: 10 Nm 3.
Secure t he door wi ndow glas s t o t he window l ift mechanis m.
4.
Inst all t he out er wais t s eal and s ecure wi th the Torx s crew.
5.
Inst all t he front door s peaker.
Refer t o: Front Door Speaker (415-01 Informat ion and Ent ert ainment
Syst em, Removal and Ins tall ati on).
6.
Connect t he batt ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
7.

Publi s hed: 11-May-2011
Glass, Frames and Mechanisms - Rear Door Window Regulator and Motor
Removal and Inst all ati on
Special T ool(s) 501-114
Releas e Lever, Door Glas s
Removal
• NOTE: If pos s ible, l ower t he wi ndow glas s by approximat el y one t hird of it s travel .
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1.
Remove t he rear door modul e.
Refer t o: Rear Door Module (RDM) (419-10 Mult ifunct ion Electronic
Modules , Removal and Ins t allat ion).
2. Carefully remove t he outer wais t s eal.
3.

Remove t he window mot or and regulat or
as sembl y. Rotat e t he as sembl y wit hin the door through 90
degrees and remove the upper edge from t he
apert ure firs t. 6.
Installation Inst all t he window mot or and regulat or as s embly. Tighten the nut s
and t he bolt s.
T orque: 10 Nm 1.
Secure t he door wi ndow glas s t o t he window l ift mechanis m.
2.
Inst all t he out er wais t s eal and s ecure wi th the Torx s crew.
3.
Inst all t he rear door modul e.
Refer t o: Rear Door Module (RDM) (419-10 Mult ifunct ion Electronic
Modules , Removal and Ins t allat ion).
4.
Connect t he batt ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
5.

Publi s hed: 11-May-2011
Glass, Frames and Mechanisms - Driver Door Window Control Switch
Removal and Inst all ati on
Removal
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
Remove t he front door t ri m panel.
Refer t o: Front Door Trim Panel (501-05 Int eri or Trim andOrnament ati on, Removal and Ins tal lat ion).
2.
Remove t he 2 s crews .Releas e t he 5 cli ps .
3.
Installation
To i nst all , revers e t he removal procedure.1.

Publi s hed: 11-May-2011
Glass, Frames and Mechanisms - Passenger Door Window Control Switch
Removal and Inst all ati on
Removal
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
Remove t he rear door t rim panel.
Refer t o: Rear Door Tri m Panel (501-05 Int erior Tri m andOrnament ati on, Removal and Ins tal lat ion).
2.
3.
Installation
To i nst all , revers e t he removal procedure.1.