2006 LAND ROVER FRELANDER 2 charging

Publ is hed: 20-Oct -2011
Battery and Charging System - General Information - Quiescent Drain
Des cript ion and Operat ion
QUIESCENT DRAIN - TYPICAL VALUES
• NOTE: The quies cent drai n aft er the init ial s hut down peri od s hould not exceed the val ue shown in t he t abl e.
Land Rover Quiescent Drain Values
MODELSHUT DO WN PER IOD(minutes)T YPICAL VALUES BAT T ERY DRAIN(mA)
Range Rover (LM) - Up t o 2009MY3016.0 - 18.0Range Rover (LM) - From 2010MY20 (aft er l ock/arm condit ion) ²<30
33 (unl ocked)<30
Range Rover Sport (LS) - Up t o 2007MY20<22Range Rover Sport (LS) - From 2007MY t o2010MY30<25
Range Rover Sport (LS) - From 2010MY3 (aft er lock/arm condit ion) ²<30
33 (unl ocked)<30
Range Rover Evoque (LV) - From 2012MY20 (aft er l ock and arm condit ion)<20Di scovery 3/LR3 (LA) - Up t o 2007MY20<22
Di scovery 3/LR3 (LA) - From 2007MY to 2010MY30<25
Di scovery 4/LR4 (LA) - From 2010MY3 (aft er lock/arm condit ion) ²<3033 (unl ocked)<30
Freelander 2/LR2 (LF) - From 2007MY35 (si ngl e l ocked or unlocked)<23.6
12 (double locked)<23.6Freelander (LN) - Up to 2007MY1024-25 - wi thout Becker Navi gati onsys t em
1027-28 - wi th Becker Navi gat ion s ys temDefender (LD) - 1998MY t o 2007MY30<21
Defender (LD) - from 2007MY<30<30
Di scovery Seri es 2 (LT)30<30
• NOTE:
1. The tot al current drain wil l be higher i f certai n approved acces sories are fi tt ed (for exampl e: tracker, t rai ler module,etc.)
2. Appl ies t o vehicles wi thout Tire Pres s ure Monit ori ng Syst em (TPMS). Vehicle shut -down peri od wi th TPMS isapproximat el y 15 minutes .

Publ is hed: 05-Dec-2011
Battery and Charging System - General Information - Charging System
Diagnosi s and Tes ti ng
Principles of Operation
For a detail ed descripti on of the chargi ng s ys t em, refer t o t he rel evant Des cript ion and Operat ion secti on in the workshopmanual. REFER to:
Bat t ery Care (414-00, Des cript ion and Operat ion),Bat t ery and Cables (414-01, Des cri pti on and Operati on),Generator - ID4 2.4L Di esel (414-02, Des cri pt ion and Operati on).
Inspection and Verification
CAUTION: Di agnos is by s ubs ti tut ion from a donor vehicle is NO T acceptabl e. Subs ti tut ion of cont rol modules doesnot guarant ee confirmat ion of a faul t, and may als o caus e addit ional fault s i n t he vehi cl e being t est ed and/or t he donorvehi cl e.
1. Verify t he cus t omer concern.1.
2. Vis ually ins pect for obvious s igns of mechani cal or electrical damage.2.
• NOTE: Check the vehicle bat tery condi ti on and st ate of charge before condemning any of the chargi ng s ys t emcomponents . For addi ti onal i nformat ion, refer to the bat tery care manual.
For a compl ete lis t of all di agnos ti c troubl e codes that coul d be l ogged on t his vehicle, pleas e refer to s ect ion 100-00.REFER to: (100-00)
Diagnos t ic Troubl e Code (DTC) Index - DTC: Engine Cont rol Module (PCM) (Des cri pt ion and Operati on),Diagnos t ic Troubl e Code (DTC) Index - DTC: Ins trument Clus ter (IPC) (Des cri pti on and Operati on).
Visual Inspection
MechanicalElectricalGenerat orDrive beltDrive belt t ensi onerGenerat or pull eyCheck the s ecurit y of t he generat or fi xings
Generat orBat teryMega-fus eEngine/generat or ground connecti onHarness (s)El ect ri cal connector(s )Engine Cont rol Module (ECM)Cent ral juncti on box (Freel ander 2 onl y)
3. If an obvious cause for an obs erved or report ed concern is found, correct t he caus e (if pos s ible) beforeproceeding t o t he next s t ep3.
4. If t he caus e is not vis ually evi dent , check for Di agnos ti c Trouble Codes (DTCs) and refer t o t he DTC Index.4.
DTC Index
• NOTE: If the control modul e or a component i s s us pect and the vehicle remains under manufacturer warrant y, refer t o theW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval programme is in operat ion, pri ort o the ins tall ati on of a new module/component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only fi ve digit codes . Mat ch the five di git s from t hes can tool to the firs t fi ve di git s of the seven digi t code l is ted to ident ify t he faul t (t he las t t wo digi ts gi ve ext rainformat ion read by the manufact urer-approved diagnost ic s ys tem).
• NOTE: W hen performing el ect ri cal volt age or resi s tance tes t s, al ways us e a digit al mult imet er (DMM) accurate to threedeci mal places , and wi th an up-to-date cali brat ion cert ificate. W hen t es ti ng res is t ance, always take t he res i st ance of t heDMM leads int o account.
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
SymptomPossible CauseAction
Charge warning l amp does noti llumi nateW arning l amp/circui t -faul tGenerat or - internalfaul tCAN Bus - ci rcuit faul tEngine control modul e- i nternal faul t
Check t he warni ng lamp functi on wit h t heignit ion on and the engine offRepai r the ci rcuit as neces s aryCheck for DTCs indicati ng a generator, CAN orengi ne cont rol module fault
Charge warning l amp s tayson/bat tery dis chargesAcces s ory drive belt -faul tGenerat or pul leys li ppi ng on s haftGenerat or - internal
Check t he batt ery and generat or cablesRefer t o the el ect ri cal guidesCheck for DTCs indicati ng a generator faul tCheck t he acces s ory drive belt condi ti on andtens ion

Publi s hed: 11-May-2011
Battery, Mounting and Cables - Battery
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1. 2.
NOTE: Appl y petroleum jell y to the bat tery
t ermi nal s .
T orque: 5 Nm 2.
3.
Installation To i nst all , revers e t he removal procedure.
1.

Publi s hed: 11-May-2011
Generator and Regulator - GeneratorI6 3.2L Petrol
Removal and Inst all ati on
Special T ool(s)
303-1255Inst all er, Generator dowels
303-1278Al igner, Timing Cover
303-502Socket , Flywheel Bolt
Removal
1. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
1.
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
2.
Remove t he int ake mani fol d.
Refer t o: Int ake Mani fol d (303-01A Engi ne - I6 3.2L Petrol, Removaland Inst all at ion).
3.
Di sconnect t he generat or harness .4.
Remove t he generat or.5.

Us ing t he s peci al t ool, i ns t all the dowel s to align the
generator.
Speci al Tool (s ): 303-1255 5.
Tight en the generat or bol ts .
T orque: 24 Nm 6.
Connect t he generator harnes s and ti ght en t he nut.
T orque: 12 Nm 7.
Inst all t he int ake mani fol d.
Refer t o: Int ake Mani fol d (303-01A Engi ne - I6 3.2L Petrol, Removal
and Inst all at ion).
8.
Connect t he batt ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
9.

Publi s hed: 11-May-2011
Generator and Regulator - GeneratorTD4 2.2L Diesel
Removal and Inst all ati on
Removal
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1.
Remove t he fuel fi lt er.
Refer t o: Fuel Fil ter (310-01B Fuel Tank and Lines - TD4 2.2L Dies el ,
Removal and Ins tall ati on).
2.
3. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
3.
Remove t he engi ne undershi eld.
Refer t o: Engi ne Unders hi eld (501-02 Front End Body Panel s ,
Removal and Ins tall ati on).
4.
Remove t he acces sory dri ve bel t.
Refer t o: Acces sory Dri ve Belt (303-05B Acces sory Drive - TD4 2.2L
Di es el, Removal and Ins tal lat ion).
5. 6.
7.

Publi s hed: 11-May-2011
Exterior Lighting - Headlamp Assembly
Removal and Inst all ati on
Removal W ARNING: Vehi cl es fi tt ed wi th Xenon headlamps , the foll owi ng precauti ons must be obs
erved. Fai lure to compl y may
res ult i n expos ure to ult ra vi ol et rays , severe el ect ri c s hock, burns or the ri sk of explos ion. Ensure t he headlamps are
s wit ched off at all ti mes . Eye and hand protecti on mus t be worn. Never swi tch on the l amps or tes t t he bul bs wit h t he
lamp hol der releas ed from t he headlamp.
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1. T orque:
4 Nm 2.
3. NOTE: Do not dis ass embl e further if t he component i s removed
for acces s onl y.
3.

Publi s hed: 11-May-2011
Exterior Lighting - Stoplamp Switch
Removal and Inst all ati on
Removal
Right-hand drive vehicles
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
Remove t he dri ver l ower ai r bag.
Refer t o: Dri ver Lower Air Bag Module (501-20B SupplementalRes traint Sys t em, Removal and Inst all at ion).
2.
3.
All vehicles
4. CAUTION: The s wit ch has a l at ching device t hatonly al lows t he s wit ch to be removed or i ns t alled whent he s wit ch plunger i s depres sed.
• NOTE: RHD ill ust rat ion shown, LHD i s s imi lar.
4.