1994 HONDA INTEGRA Workshop Manual

Engine Removal/lnstallation
SIDE ENGITIEMOUNT
5-12

Engine Installation
Install the engine in the reverse order of removal.
Reinstall the mount bolts/nuts in the following sequence.
Failure to tollow these procedures may cause excessive
noise and vibration, and reduce bushing life.
1. Install the transmission mount, then tighten the
bolt/nuts on the transmission side. Leave the mount
bolt loose.
A/T:
12 x 1.25 mm64 N.m (6.5 kgt.m,47 rbf.ft)
M/T:
12 x 1.25 mm64 N.m 16.5 kgl.m,47 tbt.frl
Install the engine side mount, then tighten the
bolt/nuts on the engine side. Leave the mount bolt
loose.
10 x 1.25 mm52 N.m {5.3 kgf.m,38 rbf.ItlReplace.
3. Tighten the mount bolt on the transmission mount.
A/T:
12 x 1 .25 nn
M/T:
74 N.m (7.5 kgl.m,54 rbf'ftt
12 x 1.25 mm74 N.m (7.5 kgt.m,54 tbt.ftl
{cont'd)
5-13

Engine Removal/lnstallation
.tE
m'
(cont'dl
4. Tighten the mount bolt on the side engine mount.
12 x 1.25 mm74 N.m (7.5 kgf.m,54 lbt.ttl
5. Install the rear mount bracket, then tighten the bolts
in the numbered sequence as shown {@ @).
@ 12 x 1.25 mm59 N.m {6.0 kgf'm, 43 lbl'It)Replace.
12 r 1.25 mm59 .m 16.0 kgl.m,
6. Install the right front mount/bracket, then tighten the
bolts in the numbered sequence as shown (O-@).
A/T:@ 10 x '1.25 mm44 N.m (4.5 kgt'm,33 tbt.fr)
O 12 x 1.25 mm64 N.m 16.5 kgt.m,47 lbf.ftlReplace.
M/T:
O 12 x 1.25 mm83 N'm (8.5 kgf.m, 61 lbt.frl
@ '10 x 1.25 mm44 N-m (4.5 kgf.m,

Insrall the left front mount, then tighten the bolts in
the numbered sequence as shown (O-@),
O 12 x 1.25 ]n]n83 N.m 18.5 kst.m,61 lbt.ftlReplace.
@ 12 r 1.25 mm59 N.m {6.0 kgl.n,43 tb{.ftlReplace.
@ 10 r 1.25 mm44 N.m (4.5 kgf.m, 33 lbt.ftl
k-
5-15
a Check that the sp.ing clip on the end of each
driveshaft clicks into place.
GAUTION: Uso oow spring clips.
a Bleed air trom the cooling system at the bleed bolt
with the heater valve open (see page 10-5).
a Adjust the th.ottle cable (see section 1 1).
a Check the clutch pedal tree play lsee section 12).
a Check that the transmission shifts into gear
smoothlv,
a Adiust the tension of the following drive belts.
Alternator belt {s€e section 23).
P/S pump belt {see section 17).
A/C comoressor belt (see section 22).
a Inspect tor fuel leakage (see section 1 1).
. After assembling fuel line parts, turn on the ig-
nition switch (do not operate th€ starter) so
that the Juel pump operates for approximat€-
lV two seconds and the tuel line pressurizes.
Repeat this operation two or three times and
check for fuel leakage at any point in the fuel
line.
(cont'd)

il
I
I
I
Mount/Bracket Torque
Mount and Bracket Eolts/Nuts Torque Valve Specification:
TRANSMISSION MOUNT:

SIDE ENGINE MOUNT:
LEFT FRONT MOUNT:
/>
Torqus Spocifications:
A: 10 x 1.25 mm
59 N.m (6.O kgf.m, 43 lbf.ft)
B: 12 x 1.25 mm
59 N.m {6.0 kgt.m. 43 lbt.ft}
Reolace.
C: 14 x 1.5 mm
118 N.m {12.O kgt.m,86.8 lbt.tt}
Replace.
D: 12 x 1.25 mm
74 N.m {7.5 kgf.m, 54 lbf.tt}
E: 12 x 1.25 mm
64 N.m (6.5 kgf.m, 47 lbf.ftl
F: 10 x 1.25 mm
52 N.m {5.3 kgl.m, 38 lbt.ft}
Replace.
G: 10 x 1.25 mmrt4 N.m (4.5 kgf.m, 33 lbf.ft)
H: 12 x 1.25 mm
83 N.m (8.5 kgt.m. 61 lbl.ft)
lr 12 x 1.25 mm
64 N.m (6.5 kgf.m, 38 lbf.tt)
Reolace.
{cont'd)
5-17

Mount/Bracket Torque
(cont'd)
REAR STIFFENER
M/T: 12 x '1.25 mm57 N.m 15.8 kgf'm,42 rbf.ft)A/T: 10 x 1.25 mm/14 N.m {4.5 kgf.m,32 tbt.ftl
ALTERNATOR BRACKET
10 x 1.25 mm
8x1.25mm24 N.m 12.4 kgf'm,
17 tbt.ftt
lO r 1.25 mm54 N'm (5.5 kgl.m,40 tbf.ft)
FRONT STIFFENER
(B18Cl engin€ onlyl
'12 x 1 .25 mm
f--^,c*;"*".*-
t-*i;
lq
I -4M
- Ghinein"onvt
ddv
HEATINSULATOR(818C1
P/S PUMP BRACKET
10 x 1.25 mm44 N.m (4.5 kgf'm, 33 lbf'ft|
57 N.m 15.8 kgt.m,42 tbf.fr)
8 x 1.25 mm24 N.m (2.4 kgf.m,17 tbf.ft)
10 x 1.25 mm 10 x 1.25 mnl44 N.m {4.5 kgf.m, 44 N.m (4.5 kgf.m,33 rbr.ftt 33 rbr.tt)
SIDE ENGINE MOUNT
BRACKET
5-18
'11 N.m (1.1 kgl'm,8 O lbf'tt)

Cylinder Head/Valve Train
81881 engine
Speciaf Tools .............6-2
Valve Clearance
Adiustment ............6-3
Valve Seals
Replacement (cylinder head
removal not required) ..................... 6-5
Reconditioning ......6-27
Timing gelt
lllustrated Index ............................... 6-7
Inspection .............. 6-9
Tension Adiustment ........................ 6-9
Removal .................6-10
Installation .............6-12
Crankshaft Pulley Bolt
Replacement .........6-8