1994 HONDA INTEGRA Workshop Manual

Differential (Automatic Transmissionl
Special Tools ........ ........ 15-20
Differential (Automatic Transmission)
flfustrated Index......... .15-21
Backfash Inspection .... 15-22
Bearing Replacement ............... ..... 15-22
Differential Carrier Replacement .... 15-23
Oil Seaf Removal ........15-24
Oil Seal Installation/
Side Clearance ............. 15-24

Special Tools
Ref. No. I Tool NumberDascriptionOty I Pago Retelonco
or^
aa)
@
oTJAD-PH80200
oTNAD-P200100
07746-0030100
07749-0010000
o7947-SD90200
Pilot, 26 x 30 mm
Driver, 52 x 55 mm
Driver, 40 mm l.D.
Driver
Oriver Attachment
1
1
1
I
1
15-26
15-26
15-22,24,25't 5-26
15-26
o@o
@@
15-20

Differential (Automatic Transmissionl
lllustrated Index
FINAL DRIVEN GEAR
BALL BEARING
--ttot"'
ENTIAL .ARRIER
ROLLER.5xlOmm
'-6
BALL BEARING
15-21

Differential (AutomaticTransmission)
Backlash InspectionBearing Replacement
1.Place the differential assembly on V-blocks and in-
stall both axles.
Check backlash of both pinion gears.
Standard (New): 0.05-O.15 mm (0.002-0.006 inl
3. lf backlash is out of tolerance, replace the differen-
tial carrier.
SIDE GEARS
NOTE: Check the bearings for wear and rough rotation.
lf the bearings are OK, removal is not necessary.
1. Remove the ball bearings using a bearing puller.
BEARING PULLER
Install the new ball bearings using the special tool
with a Dress as shown.
BALL BEAING
DRIVER, 40 mm l.D.07746 0030100
15-22

Differential Carrier Replacement
1.Remove the final driven gear from the differential
carrier.
NOTE: Tho final driven gear bolts have left-hand
threads.
Pry the snsp ring ofl differential carrier. then remove
the speedometer drive gear 8nd 5 x 1O mm roller.
lnstall th6 5 x 1O mm roller in the differentisl csrrier'
Install the speedom€ter drive gear with its chamfered
side facing the carrier, Align the cutout on the bore
of the speedometer drive gesr with the 5 x 10 mm
roll€r.
5.
4.
SPEEDOMETEBDRIVE GEARInstsll in thisdiroction.
DRIVE GEAR
5. Align the hooked end of the snap ring with the pin-
ion shaft as shown, then installthe snap ring in the
diff€rential carrior groove.
Hooksd €nd
SI{AP RII{GInstall in this direction.
o.Install the final driven gear, then tighten the bolts
to th6 spscified torque.
TOROUE: 101 N.m (10.3 kgf.m, 74.5 lbf.ft)
NOTE: The final driven gear bolts have left-hand
threads.
BOLTS10 r 1.0 mmlOi N.m (1O.3 kgf.m,74.5 tbt'ft)Left-hand thrgads
7. Install the ball bearings {see page 15-22).
15-23

Differential (Automatic Transmissionl
Oil Seal Removal
Remove the differential assembly.
Remove the oil seal from the transmission housino.
TRAt{SMtSStONHOUSING
1.
2.
Oil Seal Installation/Side Clearance-
1. lnstalla 2.50 mm (O.O98 in) thrust shim in the rrans-
mission housing.
NOTE: Do not install the oil seal yet.
TRANSMISSIOHOUSING
Install the differential assembly into the torque con_v€ner housing using the special tool as shown.
DRIVER, 40 mm l.D.07746-OO30100
DIFFERENTIALASSEMBLY
/-l
TOROUE CONVERTERHOUSING
Assemble the transmission (see section 14).
Installthe transmission housing and tighten the bolts(see section 14).
OIL SEALReplace.
seal from therorque convener
TOROUE CONVERTERHOUSING
15-24

Tap on the transmission housing side of the differen-
tial assembly with the special tool to seat the
dilferential assembly in the torque converter housing.
Measure the clearance between the thrust shim and
outer race of the ball bearing in the t.ansmission
housing.
STANDARD: O-0.15 mm {0-O.OO6 in}
lf out of limits, select a new thrust shim from the
following table:
THFUST SHIM, 80 mm
NOTE: It the thrust shim-to-ball bearing outer race
clearance measured in step 5 is less than the specifi-
cation, it is not necessa.y to pertorm steps 7 and 8.
Remove the transmission housing.
ReDlace the 2.50 mm (0.098 in) thrust shim with
the one oJ the correct thickness selected in step 6.
Install the transmission housing (see section 14).
(cont'd)
8.
Pan Numb€rThickness
90414-689-OOO
90415-689-OOO
90416-689-000
9041 7- 689-000
904r 8-689-OOO
90419-PH8-OOO
2.50 mm (O.O9843 in)
2.60 mm {0. I 0236 in)
2.70 mm (O.10630 in)
2.8O mm (O. 1 1O24 in)
2.90 mm (0.1 1416 in)
3.OOmm{O.11811in)
9.
15-25

Differential (Automatic Transmissionl
Oil Seal Installation/Side Clearance
(cont'dl
9. Installthe oil seal in the transmission housing usingthe special tools as shown.
DRIVER07749-0010000
ATTACHMENT07947 -SD90200
26x30mmoTJAD-PH80200
10. Install the oil seal in the torque converter housing
using the special tools as shown.
DFIVER07749-0010000
DRIVER, 52 x 55 mmoTNAD-P200100
PILOT
15-26