1994 HONDA INTEGRA Workshop Manual

Headliner
9, Lower the headliner as shown.
NOTE: Take care not to bend and scratch the
headliner.
Replacement {cont'd)
LEFT OUARTER PILLAR
TRIM PANEL
11.
RIGHT OURTER PILLARTRIM PANEL
1O. Bemove the headliner through the hatch opening'
Installation is the reverse of the removal procedure.
NOTE:
a When inserting the headliner through the hatch
opening, be careful not to fold or bend it. Also,
be careful not to scratch the bodY.
a Check that both sides of the headliner are secure-
ly attached to the trim and Panels.
a When installing the roof trim, install the Joint
toward the rear.
20-100
HEADLINER
HEADLINER
Sodan
'1.Remove:
a Center Dillar lower trim (see page 20-94)
a Front and rear door trim lsee page 20-94)
a Front pillar trim (see page 2O-9 .
a Center pillar trim (see page 20-94)
a Rear pillar trim panel (see page 20 95)
a Rearview mirror (see Page 20-521
Remove the sunvisor and holder from each side


: Screw locationS, 6
2.
^l
s,1
LOCK WASHER
loutsidel
HOLDER
/
$-.unu,"o"
/' BRACKET
NOTE:
a lf necessary, remove the sunvisor bracket as
shown.
a When installing the sunvisor bracket, apply grease
and make sure it's installed properly.
,@
suNvrsoR

3. Remove the tront and rear ceiling lights, then dis-connect the connectors.
A : Screw, nut locations
AA: Sc.6w, 2 B : Nur, 2
CONNECTOR
CEILING
REAR CEILINGLIGHT
CONNECTOR
HOOKS
4. Remove the grab handles (tront andsenger'sl and grab hole caps (driver,s).


: Sc.sw locatioh! l2l
rear pas'
-A-i
orlx
.-L----- ----z
GRAB HOLE CAPS
20-101

Headliner
Replacement {cont'd)
5. Remove the .ool trim (moonroof modell.
6. Detach the clips by sliding the headliner forward.
A : Clip locations, 3
HEADLINER
Remove the headliner through the passenger's door
opening.
lnstallation is the reverse ot the removal procedure
NOTE:
a When inserting the headliner through the door
opening. be careful not to fold or bend it. Also,
be careful not to scratch the body
a Check that both sides ot the headliner are secure-
ly attached to the trim and Panels.
a When installing the roof trim, install the joint
toward the rear.
)
HEADLINER
20-102

Seats
Front Seat Removal
NOTE: Take care not to scratch the seat covers andbodY.
1 . Slide the lront seat backward, then remove th6 bohs,
Slide the front seat forward, then romove the seattrack end covers.
CAUTlOltl: When prying wlth E flat tip scr.wddvor,w.ap lt whh protactive tapo to prevont damago,
> i Eolt locltlon.. 2
3. Remove the bolts.
V:Boh locatlong
A V : Bolt, 1
I'
> : 8olt,
@8 x '1.25 mm Iii i.:iiil..i'xst.^. I16:t'ftt
- /)
4.
NOTE: When insralling, use--iliquid thread lock.
Lift the front seat, then disconnect the connector(driver's).
Carefully remove the front seat through the dooropening.
Installation is the reverse of the removal procedure.
CONNECTOR
20-103

Seats
NOTE: Take care not to scratch the seat covers and
body.
1. Remove the front seat through the door opening (see
page 20-1O3).
2. Remove the screws and recline knob, then remove
the recline cover.
RECLINE COVER SCREW
Remove the screws, then remove the center cover.
SEAT BELTBUCKLE{see page 2O'1 '1 7)
CENTER COVER
scREws
Remove the hook and fastener, then lold the seat-
back cover back.
20-104
Front Seat RePlacement
5, Fold the seat-back cover and pad, then remove the
bolts.
> : Bolt location., 2
lnnrnt Iv)* |lO x 1.25 mm i47 N'm 14.8 kgl ln, I"?"!."t _J
SEAT.gACKCOVER
PAO
6. Remove the Pivot nut.PIVOT WASHER
PLAINWASHER
PIVOT NUT8 r 1.25 mm22Nm12.2kgl'm,16 lbf.ftl
7.Remove the seat-back.
NOTE: Take care not tobend the hinge bracket.
+ sEAr-BAcK

8. Separate the seat cushion and seat tracks.
NOTE:
a Before separating, slide the seat cushionbackward.
a Take care not to bend the joint rod.
< : Bolt locations, 4
JOINT BOD
Disconnect the rear seat access cable (hatchback
passenger'sl.
REAR SEATACCESS CABLE
RECLINEAOJUSTER
9. Separate the seat track and recline adiuste..


: Bolt, nut locations
A

: Bolt, IBY : Nut, 2
j
A;iil;iiry-,'- j @i+ilJ
_o()_ _/ _ _].'*",
RECLINEADJUSTER
Installation is the reverse of the removal procedure.
NOTE:
a To prevent wrinkles when installing a seat-backcover, make sure the material is stretched even,ly over the pad before securing all the hooks.a Apply grease to the moving surtaces.
10.
20-105

Seats
Front Seat Cover RePlacement
CAUTION: Wear gloves to removo and install the 36at
cov€rs.
NOTE: Take care not to tear the seams or damage the
seat covers.
Soat-back covor lomoval:
1. Slide the Jront seat forwa.d and told the seat-back
forward.
2. Remove the hooks and fasteners. then fold the seat-
back cover back.
FASTE]IIER
FASTENER
Remove the headrest and headrest guide.
HEAOREST
SEAT.BACK
Scr€w location,
,e, I
Yi
cJ/
4. Remove the lumbar support knob.
ilff-]s)
\
fH".,
5. Remove the seat-back cover by releasing the inside
chps.
Cllp removrl:
6. Pull back the edge of the seat-back cover all the way
around, then release the clips.
20-106
-

Seat cushion romoval:
1. Remove the seat cushion from the seat tracks (see
page 20-105).
2. Remove all clips from under the seat cushion, then
loosen the seat cushion cover
Cllp romoval:
Pull back the edge of the seat cushion cover all the
way arounC, then release the clips.
SEAT CUSHIONCOVER
2
CLIP
SEAT CUSHION COVER
Installation is the reverse of the removal ptocadtr!.
NOTE:
a To prevent wrinkles when installing a seat cover,
make sure the material is stretched evenly over
the pad before securing all the clips.a Replace the.eleased clips with new ones.
UPHOLSTERY RING PLIERS
NEW CLIP
PAD
WIRE {Pad sido}
20-107