2008 MITSUBISHI SHOGUN Owner's Manual (in English)

Instruments and controls
3-61
3
Dipper (High/Low beam change)
E00506200055
When the lamp switch is in the “ ” position, the beam changes from high to low (or low
to high) each time the lever is
pulled fully (1). While the high b
eam is on, the high beam indi-
cation lamp in the instrument cluster will also illuminate.
Headlamp flasher
E00506300128
The high beams flash when the lever is pulled slightly to (2), and will go off when it is released. When the high beam is on, th
e high beam indication lamp in
the instrument cluster will illuminate.NOTE●
The high beams can also flash when the lamp switch is OFF.
●
If you turn the lamps off with the headlamps set to high beam, the headlamps are automa
tically returned to their
low-beam setting when the lamp
switch is next turned to
the “ ” position.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
61 Wednesday, January 9, 2008 4:32 PM

3-62 Instruments and controls
3
Headlamp levelling
E00517400015
Headlamp levelling switch*
E00517500133
Except for vehicles with discharge headlampsThe angle of the headlamp beam varies depending upon the load carried by the vehicle. The headlamp levelling dial can
be used to adjust the headlamp
illumination distance (when the lower beam is illuminated) sothat the headlamps’ glare does
not distract other drivers.
Set the dial according to
the following table.
NOTE●
When adjusting the beam position, first put the dial in the “0” position (the highest beam position).
CAUTION
!●
Always perform adjustments before driving. Do not attempt to adjust while driving, as it could cause an accident.
LHD RHD
BK-BK2008E1ENUK.en-uk-Section6.fm Page
62 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-63
3
3-door models•:1 person
:Full luggage loading
5-door models•:1 person
:Full luggage loading
Vehicle conditionSwitch position
“0” “0” “2” “3” “4”
Switch position 0- Driver only/Driver + 1 front passenger Switch position 2- 5 passengers (including driver)Switch position 3- 5 passengers (including driver) + Full luggage
loading
Switch position 4- Driver + Full luggage loading
Ve h i c l e conditionSwitch position
“0” “0”
“1” or “2”
“2” “3” “4”
Switch position 0- Driver only/Driver + 1 front passenger Switch position 1- Driver + 1 front passenger + 2 passengers on
third seat (vehicles with automatic transmis-sion)
Switch position 2- Driver + 1 front passenger + 2 passengers on
third seat (vehicles with manual transmission)
Switch position 2- 7 passengers (including driver) Switch position 3- 7 passengers (including driver) + Full luggage
loading
Switch position 4- Driver + Full luggage loading
BK-BK2008E1ENUK.en-uk-Section6.fm Page
63 Wednesday, January 9, 2008 4:32 PM

3-64 Instruments and controls
3
Automatic headlamp levelling*
E00517600017
Vehicles with discharge headlampsThis function automatically adjusts the illumination distance of the headlamps according to the nu
mber of people and the load
in the vehicle.When the ignition switch is in the “ON” position and the lamp switch is in the “ ” position, the illumination distance of the headlamps is automatically adjusted when the vehicle is stopped.Automatic headlamp levelling warning lampThe automatic headlamp levelling warning lamp should illumi- nate when the ignition switch
is turned “ON”, and should go
off in a few seconds.
CAUTION
!●
If the warning lamp
stays on or does not illuminate
when the ignition switch is
turned “ON”,
it indicates
that the automatic headlamp
levelling device is not
functioning. We recommend you to have your vehicle inspected.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
64 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-65
3
Turn-signal lever
E00506500771
NOTE●
If the lamp flashes unusually quickly, the bulb in a turn- signal lamp may have burned out. We recommend you to have the vehicle inspected.
●
It is possible to activate the following functions. For fur- ther information, we recommend you to consult a MIT- SUBISHI MOTORS Author
ized Service Point.
• Sounding of a buzzer as the turn-signal lamps flash• Flashing of the turn-signal lamps when the lever is oper- ated with the ignition switch in the “ACC” position • The turn signal-lamps 3-flash function for lane changescan be deactivated. • The time required to operate the lever for the 3-flash function can be adjusted.
1- Turn-signals
When making a normal turn, use position (1). The lever willreturn automatically when cornering is completed.
2- Lane-change signals
When changing lanes, use position (2). It will return to theneutral position when released.Also, when you move the lever to (2) slightly then release it,the turn-signal lamps and indication lamp in the instrumentcluster will flash 3 times.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
65 Wednesday, January 9, 2008 4:32 PM

3-66 Instruments and controls
3
Hazard warning flasher switch
E00506600440
Use the hazard warning flasher switch when the vehicle has to be parked on the road for any emergency. The hazard warning flashers can always be operated, regard-less of the position of the ignition key. Push the switch to turn on the
hazard warning flashers, all turn-
signal lamps flash continuously. To turn them off, push the switch again.NOTE●
It is possible for a buzzer to
sound with flashing of the
turn-signal lamps. For furt
her information, we recom-
mend you to consult a MITSUBISHI MOTORS Author-ized Service Point.
Fog lamp switch
E00506700047
Front fog lamp switch*
E00508300281
The front fog lamps illuminate only when the headlamps or taillamps are on. Push the switch to turn on the front fog lamps,and push the switch again to turn them off. The indication lamp in the instrument cluster will illuminate while the front fog lamps are on.LHD RHD
BK-BK2008E1ENUK.en-uk-Section6.fm Page
66 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-67
3
NOTE●
The front fog lamps are automa
tically turned off when the
headlamps or tail lamps turn off. To turn on the front fog lamps again, push the switch
again when the headlamps or
tail lamps turn on.
●
In case of vehicles with Da
ytime Running Lamp, the front
fog lamp can be operated even if the lamp switch is set to the “OFF” position.
Rear fog lamp switch
E00508400123
The rear fog lamp illuminates only when the headlamps orfront fog lamps (if so equipped) are on. Push the switch to turn on the rear fog lamp, and push the switch again to turn it off.The indication lamp in the instrument cluster will illuminate while the rear fog lamp is on.Type 1LHD RHD
BK-BK2008E1ENUK.en-uk-Section6.fm Page
67 Wednesday, January 9, 2008 4:32 PM

3-68 Instruments and controls
3
Type 2NOTE●
The rear fog lamp is automa
tically turned off when the
headlamps or front fog lamps (if so equipped) turned off.To turn on the rear fog lamp
again, push the switch again
when the headlamps or front fog lamps (if so equipped) turn on.
●
In case of vehicles with Da
ytime Running Lamp, the rear
fog lamp can be operated even if the lamp switch is set to the “OFF” position.
Wiper and washer switch
E00507101191
LHD RHD
CAUTION
!●
If the washer is used in cold weather, the washer fluid sprayed against the
glass may freeze, which
may hinder visibility. Wa
rm the glass with the
defroster or rear window demister before using thewasher.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
68 Wednesday, January 9, 2008 4:32 PM