2008 MITSUBISHI SHOGUN instrument cluster

Instruments and controls
3-61
3
Dipper (High/Low beam change)
E00506200055
When the lamp switch is in the “ ” position, the beam changes from high to low (or low
to high) each time the lever is
pulled fully (1). While the high b
eam is on, the high beam indi-
cation lamp in the instrument cluster will also illuminate.
Headlamp flasher
E00506300128
The high beams flash when the lever is pulled slightly to (2), and will go off when it is released. When the high beam is on, th
e high beam indication lamp in
the instrument cluster will illuminate.NOTE●
The high beams can also flash when the lamp switch is OFF.
●
If you turn the lamps off with the headlamps set to high beam, the headlamps are automa
tically returned to their
low-beam setting when the lamp
switch is next turned to
the “ ” position.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
61 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-65
3
Turn-signal lever
E00506500771
NOTE●
If the lamp flashes unusually quickly, the bulb in a turn- signal lamp may have burned out. We recommend you to have the vehicle inspected.
●
It is possible to activate the following functions. For fur- ther information, we recommend you to consult a MIT- SUBISHI MOTORS Author
ized Service Point.
• Sounding of a buzzer as the turn-signal lamps flash• Flashing of the turn-signal lamps when the lever is oper- ated with the ignition switch in the “ACC” position • The turn signal-lamps 3-flash function for lane changescan be deactivated. • The time required to operate the lever for the 3-flash function can be adjusted.
1- Turn-signals
When making a normal turn, use position (1). The lever willreturn automatically when cornering is completed.
2- Lane-change signals
When changing lanes, use position (2). It will return to theneutral position when released.Also, when you move the lever to (2) slightly then release it,the turn-signal lamps and indication lamp in the instrumentcluster will flash 3 times.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
65 Wednesday, January 9, 2008 4:32 PM

3-66 Instruments and controls
3
Hazard warning flasher switch
E00506600440
Use the hazard warning flasher switch when the vehicle has to be parked on the road for any emergency. The hazard warning flashers can always be operated, regard-less of the position of the ignition key. Push the switch to turn on the
hazard warning flashers, all turn-
signal lamps flash continuously. To turn them off, push the switch again.NOTE●
It is possible for a buzzer to
sound with flashing of the
turn-signal lamps. For furt
her information, we recom-
mend you to consult a MITSUBISHI MOTORS Author-ized Service Point.
Fog lamp switch
E00506700047
Front fog lamp switch*
E00508300281
The front fog lamps illuminate only when the headlamps or taillamps are on. Push the switch to turn on the front fog lamps,and push the switch again to turn them off. The indication lamp in the instrument cluster will illuminate while the front fog lamps are on.LHD RHD
BK-BK2008E1ENUK.en-uk-Section6.fm Page
66 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-67
3
NOTE●
The front fog lamps are automa
tically turned off when the
headlamps or tail lamps turn off. To turn on the front fog lamps again, push the switch
again when the headlamps or
tail lamps turn on.
●
In case of vehicles with Da
ytime Running Lamp, the front
fog lamp can be operated even if the lamp switch is set to the “OFF” position.
Rear fog lamp switch
E00508400123
The rear fog lamp illuminates only when the headlamps orfront fog lamps (if so equipped) are on. Push the switch to turn on the rear fog lamp, and push the switch again to turn it off.The indication lamp in the instrument cluster will illuminate while the rear fog lamp is on.Type 1LHD RHD
BK-BK2008E1ENUK.en-uk-Section6.fm Page
67 Wednesday, January 9, 2008 4:32 PM