2008 MITSUBISHI SHOGUN low beam

3-10 Instruments and controls
3
Indicator and warning lamps
E00501501353
1- Turn-signal indication lamps/Hazard warning indication
lamps
→ p. 3-12
2- Rear fog lamp indication lamp
→ p. 3-12
3- Position lamp indication lamp
→ p. 3-12
4- Front fog lamp indication lamp*
→ p. 3-12
5- Automatic headlamp levelling warning lamp*
→ p. 3-64
6- High-beam indication lamp
→ p. 3-12
7- Active stability control function OFF indication lamp
→ p. 4-67
8- Active stability control function indication lamp/Active trac-
tion control function indication lamp
→ p. 4-67, 4-69
9- Anti-lock brake system (ABS) warning lamp
→ p. 4-60
10- Brake warning lamp
→ p. 3-13
11- Supplemental restraint system (SRS) warning lamp
→ p. 2-75
12- Seat belt warning lamp
→ p. 2-40
13- A/T fluid temperature warning lamp (vehicles with A/T)
→ p. 4-31
14- CRUISE indication lamp*
→ p. 4-72
15- “SONAR OFF” indication lamp*
→ p. 4-84
16- Diesel particulate filter (DPF) warning lamp*
→ p. 4-22
17- Diesel preheat indication lamp (diesel-powered vehicles)
→ p. 3-12
18- Fuel filter indication lamp (diesel-powered vehicles)
→ p. 3-13
19- Check engine warning lamp
→ p. 3-15
20- Charge warning lamp
→ p. 3-16
21- Oil pressure warning lamp
→ p. 3-16
22- Low fuel warning lamp
→ p. 3-8
23- 2WD/4WD operation indication lamp
→ p. 4-38
BK-BK2008E1ENUK.en-uk-Section6.fm Page
10 Wednesday, January 9, 2008 4:32 PM

3-12 Instruments and controls
3
Indicator lamps
E00501600012
Turn-signal indication lamps/Hazard warning indication lamps
E00501700068
These indication lamps blink on and off when a turn-signal lamp is operating.NOTE●
If the blinking is too fast, a lamp bulb may be blown or a turn-signal connection may be false.
When the hazard warning lamp switch is pressed, all turn-signal lamps will flash on andoff continuously.High-beam indicator lamp
E00501800072
This indicator lamp illuminates when the highbeam is used.Front fog lamp indication lamp*
E00501900132
This indication lamp illuminates while the frontfog lamps are on.
Rear fog lamp indication lamp
E00502000084
This indication lamp illuminates while the rearfog lamp is on.Position lamp indication lamp
E00508900102
This lamp illuminates with the lamp switch at “ ” or “ ” position.Diesel preheat indica
tion lamp (diesel-
powered vehicles)
E00502300029
This indication lamp illuminates when the igni- tion switch is placed in the “ON” position. Asthe glow plug becomes hot, the lamp goes out and the engine can be started.NOTE●
If the engine is cold,
the diesel preheat indi-
cation lamp is on for a longer time.
●
When the engine has not been started within about 5 seconds after the diesel preheatindication lamp went out, return the ignition switch to the “LOCK” position. Then, turn the switch to the “ON” position to preheat the engine again.
●
When the engine is warm, the diesel preheat indication lamp does not come on even if the ignition switch is placed in the “ON” position.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
12 Wednesday, January 9, 2008 4:32 PM

3-60 Instruments and controls
3
●
If the lamps do not turn on or off with the switch in the “AUTO” position, manually operate the switch and we recommend you to have your vehicle checked.
Daytime running lamp
*
When the ignition switch is in the “ON” position and the lamp switch is set to the “OFF” position, the low beam of the head-lamps, tail lamps, etc., will illuminate.Lamps (headlamps, fog lamps, etc.) auto-cutout function●
If the ignition key is turned to “LOCK” or “ACC” posi- tion or removed from the ignition switch, and without opening the driver’s door for 3 minutes while the lamp switch in the “ ” position, the lamps will turn off auto- matically.
●
If the ignition key is turned to “LOCK” or “ACC” posi- tion or removed from the ignition switch and the driver’s door is opened within 3 minutes while the lamp switch in the “ ” position, a buzzer will sound to warn the driver that the lamps have not been turned off, and these lamps will automatically turn off.
NOTE●
The lamp auto-cutout will not function when the lamp switch is in the “ ” position.
●
When the ignition key has b
een turned to either the
“LOCK” or “ACC” position or removed from the ignition switch with the lamp switch in the “ ” position, and the lamp switch is returned to the “OFF” position within approximately 3 minutes, the auto-cutout function will notbe activated.
When you want to keep the lamps on●
Turn the lamp switch in the “OFF” position while the ignition key is in the “LOCK” or “ACC” position.
●
Turn on the lamps with the switch in the “ ” or “ ” position again, then the lamps will remain on.
●
Remove the ignition key.
NOTE●
For further information, we recommend you to consult MITSUBISHI MOTORS Authorized Service Point.
Lamp monitor buzzer
E00506100256
If the driver’s door is opened when the ignition key is in the“LOCK” or “ACC” position or removed from the ignitionswitch while the lamps are on,
a buzzer will sound to remind
the driver to turn off the lamps. When the lamp auto-cutout func
tion acts, the buzzer will stop
automatically.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
60 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-61
3
Dipper (High/Low beam change)
E00506200055
When the lamp switch is in the “ ” position, the beam changes from high to low (or low
to high) each time the lever is
pulled fully (1). While the high b
eam is on, the high beam indi-
cation lamp in the instrument cluster will also illuminate.
Headlamp flasher
E00506300128
The high beams flash when the lever is pulled slightly to (2), and will go off when it is released. When the high beam is on, th
e high beam indication lamp in
the instrument cluster will illuminate.NOTE●
The high beams can also flash when the lamp switch is OFF.
●
If you turn the lamps off with the headlamps set to high beam, the headlamps are automa
tically returned to their
low-beam setting when the lamp
switch is next turned to
the “ ” position.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
61 Wednesday, January 9, 2008 4:32 PM

3-62 Instruments and controls
3
Headlamp levelling
E00517400015
Headlamp levelling switch*
E00517500133
Except for vehicles with discharge headlampsThe angle of the headlamp beam varies depending upon the load carried by the vehicle. The headlamp levelling dial can
be used to adjust the headlamp
illumination distance (when the lower beam is illuminated) sothat the headlamps’ glare does
not distract other drivers.
Set the dial according to
the following table.
NOTE●
When adjusting the beam position, first put the dial in the “0” position (the highest beam position).
CAUTION
!●
Always perform adjustments before driving. Do not attempt to adjust while driving, as it could cause an accident.
LHD RHD
BK-BK2008E1ENUK.en-uk-Section6.fm Page
62 Wednesday, January 9, 2008 4:32 PM

Starting and driving
4-15
4
NOTE●
For vehicles equipped with Daytime Running Lamps, when the ignition switch is in the “ON” position, the headlamp low beams etc. are turned on. Refer to “Headlamps” on page 3-58.
●
Your vehicle is equipped wi
th an electronic immobilizer.
To start the engine, the ID code which the transponder inside the key sends must match the one registered to theimmobilizer computer. Refer to “Electronic immobilizer” on page 1-3.
Ignition switch illuminationIn the situations listed below, the ignition switch illumination comes on to facilitate insertion or removal of the ignition key.●
When any door or the backdoor is opened, the ignition switch illumination comes on. When it is closed, the igni- tion switch illumination becomes steadily dimmer untilcompletely going off about 15 seconds later.
●
When the ignition key is removed with all the doors and the backdoor closed, the ignition switch illuminationcomes on and stays on
for about 15 seconds.
The ignition switch illumination immediately goes off if any of the following actions is taken while it is on. ●
All the doors and the backdoor are closed, and the ignition switch is turned to the “ON” position.
●
All the doors and the backdoor
are locked using the cen-
tral door locking function.
●
All the doors and the backdoo
r are locked using the key-
less entry system (if so equipped).
BK-BK2008E1ENUK.en-uk-Section7.fm Page
15 Wednesday, January 9, 2008 4:36 PM

Maintenance
8-33
8
●
Some fuses may not be installed on your vehicle, depend- ing on the vehicle model or specifications.
●
The table above shows the main equipment corresponding to each fuse.
Identification of fuse
E01008100092
20 Front fog lamps 15 A 21 — — — 22 Windscreen wiper 20 A 23 Tail lamp (right) 7.5 A 24 Tail lamp (left) 7.5 A 25 Headlamp low beam (right)
10 A*
2
20 A*
3
26 Headlamp low beam (left)
10 A*
2
20 A*
3
27 Headlamp high beam (right) 10 A 28 Headlamp high beam (left) 10 A 29 Audio
30 A*
1
30 Heater
50 A*
1
*1: Fusible link
*2: Vehicles without discharge headlamps
*3: Vehicles with discharge headlamps
No.
Symbol
Electrical system
Capacity
7.5 A Brown 10 A Red 15 A Blue 20 A Yellow (fuse type)/Light blue (fusible link type)25 A Transparent 30 A Green (fuse type)/Pink (fusible link type) 40 A Green 50 A Red 60 A Yellow 140 A Reddish brown
BK-BK2008E1ENUK.en-uk-Section11.fm Page
33 Wednesday, January 9, 2008 4:50 PM

8-36 Maintenance
8
Replacement of lamp bulbs
E01003100521
Before replacing a bulb, ensure the lamp is off. Do not touch the glass part of the new bulb with your bare fingers; the skin oil left on the glass will evapor
ate when the bulb gets hot and
the vapor will condense on th
e reflector and dim the surface.
NOTE●
Do not attempt to repair or
replace the lamp bulbs other
than described in this owner’s manual. For repair or replacement, contact a MITS
UBISHI MOTORS Author-
ized Service Point.
●
If you are unsure of how to carry out the work as required, we recommend you to consult a specialist.
●
Be careful not to scratch the vehicle body when removing a lamp or lens.
●
When it rains or when the
vehicle has been washed, the
inside of the lens sometimes becomes foggy. This is the same phenomenon as when window glass mists up on a humid day, and does not indicate a functional problem.When the lamp is switched on, the heat will remove the fog. However, if water gathers inside the lamp, we recom- mend you to have it checked.
Bulb capacity
E01003200014
When replacing a bulb, use a new bulb with the same wattageand colour.Outside
E01003301618
Codes in parentheses indicate bulb types.
CAUTION
!●
Bulbs are extremely hot immediately after being turned off. When replacing a bulb, wait for it to cool sufficiently before touching it. You could otherwise be burnt.
1- Headlamps, high beam: 65 W (H9) 2- Front fog lamps*: 55 W (H11) 3- Headlamps, low beam with discharge lamp: 35 W (D2S)
Headlamps, low beam without discharge lamp: 55 W (H11)
4- Position lamps: 5 W (W5W) 5- Front turn-signal lamps: 21 W (WY21W)
BK-BK2008E1ENUK.en-uk-Section11.fm Page
36 Wednesday, January 9, 2008 4:50 PM