2008 MITSUBISHI SHOGUN Owner's Manual (in English)

Instruments and controls
3-53
3
4. Once more press the “
←” function button to select
“YES”.
5. Press the “SET” function button.
6. The display shown below will appear, and the display
items will return to their factory settings.
NOTE●
If the battery terminals are di
sconnected, the settings for
the date and time may be erased. If this happens, please set the date and time again.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
53 Wednesday, January 9, 2008 4:32 PM

3-54 Instruments and controls
3
Adjusting the barometer
E00524400017
It is possible to adjust the barometer indication and return it to the factory setting.NOTE●
It is not necessary to adjust the barometer because it has been adjusted at the factory. However, if you wish, adjust it using an accurate barome- ter.
To adjust the barometer 1. Press the “ADJ” button to select the barometer adjustment
display.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
54 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-55
3
2. Press the “
←” or “
→” function button to select the
“BAROMETER ADJUST” display. Then press the “SELECT” function button.
3. Adjust the barometer by pressing the function buttons.NOTE●
You can return to the previous display by pressing the “BACK” function button.“+”- To adjust the barometer
Each gentle press of the “+” function button willincrease the indicated barometer by 2 hPa. If you con-tinue pressing the button for about 2 seconds or longer,the indication is fast-forwarded
“-”- To adjust the barometer
Each gentle press of the “-” function button willdecrease the indicated barometer by 2 hPa. If you con-tinue pressing the button for about 2 seconds or longer,the indication is fast-forwarded.
“SET”- To set the barometer
Press the “SET” function button. The display will flashtwice, and the new setting will be established.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
55 Wednesday, January 9, 2008 4:32 PM

3-56 Instruments and controls
3
4. After setting the barometer adjust, press the “INFO” but-
ton to return to the information display.
Resetting to the factory setting 1. Press the “ADJ” button to select the barometer adjustment
display. Press the “
←” or “
→” function button to select the
“BAROMETER DEFAULT” display. Then press the “SELECT” function button.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
56 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-57
3
2. Press the “SET” function button. The display will flash
twice and the barometer indication will return to the fac- tory setting.
NOTE●
Although the barometer value is changed to the factory setting, a barometer unit you have selected is unchanged.
●
You can return to the previous display by pressing the “BACK” function button.
3. After setting the barometer default, press the “INFO” but-
ton to return to the information display.
Care of the monitor
E00519700012
If the monitor becomes covered in fingerprints or otherwise dirty, clean it with a soft and dry cloth.NOTE●
Don’t use a wet cloth or abrasive cleaner as this may cause damage.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
57 Wednesday, January 9, 2008 4:32 PM

3-58 Instruments and controls
3
Combination headlamps
and dipper switch
E00506001353
HeadlampsNOTE●
Do not leave the lights on for a long time while the engine is stationary (not running). A run-down battery could result.
●
When it rains, or when the
vehicle has been washed, the
inside of the lens sometimes becomes foggy, but this does not indicate a functional pr
oblem. When the lamp is
switched on, the heat will
remove the fog. However, if
water gathers inside the lamp, we recommend you to have it checked.
Type 1Rotate the switch to turn on the lamps.OFF All lamps off
Position, tail, licence plate and instrument panel lamps on Headlamps and other lamps go on
BK-BK2008E1ENUK.en-uk-Section6.fm Page
58 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-59
3
Type 2Rotate the switch to turn on the lamps.
NOTE●
The sensitivity of the automatic on/off control can be adjusted. For further information, we recommend you to consult a MITSUBISHI MOTORS Auth
orized Service Point.
●
When the headlamps are turned off by the automatic on/off control with the ignition switch in the “ON” posi- tion, the front fog lamps (if so equipped) and rear foglamps also go off. When the headlamps are subsequently turned back on by the automatic on/off control, the front fog lamps also come on but the rear fog lamps stay off. Ifyou wish to turn the rear fo
g lamps back on, operate the
switch again.
●
Do not cover the sensor (A) for the automatic on/off con- trol by affixing a sticker or label to the windscreen.
OFF All lamps off AUTO
With the ignition switch in the “ON” position, head- lamps, position, tail, licence plate, and instrument panel lamps turn on and off automatically in accord-ance with outside light level. All lamps turn off auto-matically when the ignition switch is turned to the “OFF” position. Position, tail, licence plate and instrument panel lamps on Headlamps and other lamps go on
BK-BK2008E1ENUK.en-uk-Section6.fm Page
59 Wednesday, January 9, 2008 4:32 PM

3-60 Instruments and controls
3
●
If the lamps do not turn on or off with the switch in the “AUTO” position, manually operate the switch and we recommend you to have your vehicle checked.
Daytime running lamp
*
When the ignition switch is in the “ON” position and the lamp switch is set to the “OFF” position, the low beam of the head-lamps, tail lamps, etc., will illuminate.Lamps (headlamps, fog lamps, etc.) auto-cutout function●
If the ignition key is turned to “LOCK” or “ACC” posi- tion or removed from the ignition switch, and without opening the driver’s door for 3 minutes while the lamp switch in the “ ” position, the lamps will turn off auto- matically.
●
If the ignition key is turned to “LOCK” or “ACC” posi- tion or removed from the ignition switch and the driver’s door is opened within 3 minutes while the lamp switch in the “ ” position, a buzzer will sound to warn the driver that the lamps have not been turned off, and these lamps will automatically turn off.
NOTE●
The lamp auto-cutout will not function when the lamp switch is in the “ ” position.
●
When the ignition key has b
een turned to either the
“LOCK” or “ACC” position or removed from the ignition switch with the lamp switch in the “ ” position, and the lamp switch is returned to the “OFF” position within approximately 3 minutes, the auto-cutout function will notbe activated.
When you want to keep the lamps on●
Turn the lamp switch in the “OFF” position while the ignition key is in the “LOCK” or “ACC” position.
●
Turn on the lamps with the switch in the “ ” or “ ” position again, then the lamps will remain on.
●
Remove the ignition key.
NOTE●
For further information, we recommend you to consult MITSUBISHI MOTORS Authorized Service Point.
Lamp monitor buzzer
E00506100256
If the driver’s door is opened when the ignition key is in the“LOCK” or “ACC” position or removed from the ignitionswitch while the lamps are on,
a buzzer will sound to remind
the driver to turn off the lamps. When the lamp auto-cutout func
tion acts, the buzzer will stop
automatically.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
60 Wednesday, January 9, 2008 4:32 PM