2008 MITSUBISHI SHOGUN reset

3-2 Instruments and controls
3
Instruments
E00500100241
Tachometer
E00500300458
The tachometer indicates the
engine speed (r/min). The
tachometer helps you to obtain more economical driving and also warns you of excessive engine speeds (Red zone).
1- Speedometer (km/h or mph + km/h) 2- Tachometer 3- Tripmeter reset button/Daytime dipper button 4- Fuel gauge5- Odometer/Tripmeter/Service reminder 6- Water temperature gauge
CAUTION
!●
When driving, watch the
tachometer to make sure
that the engine speed indi
cation does not rise into
the red zone (excessive engine rpm).
BK-BK2008E1ENUK.en-uk-Section6.fm Page 2 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-3
3
Odometer/Tripmeter/Service reminder
E00500600998
With the ignition switch in the “ON” position, odometer, tripm- eter, and service reminder indications are given.
Odometer The odometer indicates the tota
l distance the vehicle has trav-
elled.TripmeterThe tripmeter indicates the dist
ance travelled during a particu-
lar trip or period. There are two tripmeter displays: TRIP and . TRIP can be used to measur
e the distance travelled since
the current trip began. At the same time, TRIP can be used to measure the dist
ance from an inte
rmediate location.
To switch the display between TRIP and TRIP , press the reset button (B) less than 1 second.
A- Odometer/Tripmeter/Service reminder B- Reset button
TRIP ODOService reminder TRIP ODO
BK-BK2008E1ENUK.en-uk-Section6.fm Page 3 Wednesday, January 9, 2008 4:32 PM

3-4 Instruments and controls
3
NOTE●
If you do not push the button for about 10 seconds while the service reminder is showing, the display will return to the odometer indication.
●
The odometer, tripmeter, an
d service reminder indications
are given for 30 seconds after the ignition switch has been turned to the “ACC” or “LOCK” position.
●
After the odometer, tripmeter, and service reminder indi- cations have gone off, they come back on for about 30 seconds if either of the fo
llowing actions takes place.
• The driver’s door is opened.• The reset button is pressed.
To reset the tripmeter To return the display to “0”, press the reset button (B) for morethan 2 second. Only the currently displayed value will be reset.NOTE●
When disconnecting the battery
terminal for a long time,
the memory of tripmeter display TRIP and are cleared, and the display returns to “0”.
Service reminder
E00517700092
The service reminder shows the number of months (1) anddriving distance (3) remaining until the next 12-monthly(15,000 km or 9,000 miles) inspection. When the next inspec- tion is nearly due, the display s
hows “-----”. At this time, a
spanner mark (2) is shown for a few seconds whenever theignition switch is turned from the “OFF” position to the “ON” position.
BK-BK2008E1ENUK.en-uk-Section6.fm Page 4 Wednesday, January 9, 2008 4:32 PM

3-6 Instruments and controls
3
Resetting the service reminder With the ignition switch in the “OFF” position, it is possible to reset the spanner mark (A) and “-----” indication (B). When they have been reset, the number of months and driving dis-tance remaining until the next inspection are shown and the spanner mark (A) is no longer shown every time the ignition switch is turned from the “OFF
” position to the “ON” position.
BK-BK2008E1ENUK.en-uk-Section6.fm Page 6 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-7
3
1. Push the reset button (D) to view the number of months
and driving distance remaining until the next inspection.
2. Give the reset button (D) a long push (at least two sec-
onds) to make the spanner mark (A) start flashing. (If youdo not touch the reset button for 10 seconds while the spanner mark is flashing, the display will revert to its orig- inal indication.)
3. Give the reset button (D) a gentle push while the spanner
mark is flashing. The “-----” indication (B) will change to “cLEAr” (C).
4. The number of months and driving distance remaining
until the next inspection will be shown.
NOTE●
It is not possible to reset the “-----” indication (B) with the ignition switch in the “ON” position.
●
When a certain distance has
been driven and a certain
period has elapsed after app
earance of the “-----” indica-
tion (B), the indication is automatically reset and the number of months until the next periodic inspection isshown.
●
If you accidentally reset th
e display, consult a MITSU-
BISHI MOTORS Author
ized Service Point.
Fuel gauge
E00500700638
The fuel gauge indicates the fuel
level in the fuel tank when the
ignition switch is in the “ON” position.
CAUTION
!●
Daily and periodic inspect
ions and maintenance are
your responsibility. Be sure to perform them to help prevent accidents and breakdowns.
F- Full E- Empty
CAUTION
!●
For petrol-powered vehicles, do not drive with an extremely low fuel level;
running out of fuel could
cause damage to the catalytic converter.
●
For diesel-powered vehicl
es, do not drive with an
extremely low fuel level;
running out of fuel could
cause damage to the fuel system.
BK-BK2008E1ENUK.en-uk-Section6.fm Page 7 Wednesday, January 9, 2008 4:32 PM

3-22 Instruments and controls
3
Average fuel consumption
E00518200052
The average fuel consumption
during the period since the last
reset is shown in (A). The aver
age value of the fuel consump-
tion is graphed every 5 minutes and the data for up to 4 hoursare shown in (B). When you press the “MANUAL”
function button in the auto
reset mode, the mode will be changed to the manual resetmode. When you press the “AUTO” function button in the manual reset mode, the mode will be changed to the auto reset mode.
NOTE●
When you turn the ignition sw
itch to the “ON” position
after turning it from the “ON” position to the “ACC” or “LOCK” position in the manual reset mode, the auto reset mode will automatically be selected.
●
When the average fuel cons
umption cannot be calculated,
“--.-” will be shown.
●
The average fuel consumptio
n changes depending on the
driving condition (road condition, driving behavior, etc.). The indication may differ from the actual fuel consump- tion. Therefore, it is reco
mmended to use the indication as
reference.
●
The unit indication can be changed to your desired setting {km/L, L/100 km, mpg (UK GALLON), or mpg (USGALLON)}. Refer to “User customization” on page 3-46.
Auto reset mode Manual reset mode
BK-BK2008E1ENUK.en-uk-Section6.fm Page
22 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-23
3
Resetting the averag
e fuel consumption
Press the “RESET” function button to reset the average fuel consumption indication.NOTE●
The average fuel co
nsumption can be reset separately for
the auto reset mode and for the manual reset mode.
●
When you turn the ignition key to the “ON” position about four hours (or more) after turning it from the “ON” position to the “ACC” or “LOCK” position in the autoreset mode, the average fuel
consumption indication will
automatically be reset.
Driving range
E00518300037
This value (A) shows the distance
(in km or miles) that can be
driven on the fuel remaining in the fuel tank. The driving range is graphed every 5 minutes and the data for up to 4 hours areshown in (B).
BK-BK2008E1ENUK.en-uk-Section6.fm Page
23 Wednesday, January 9, 2008 4:32 PM

3-24 Instruments and controls
3
NOTE●
When the driving range is 50 km (30 miles) or less, the display shows “----”. When it is 3,000 km (2,000 miles) or more, “3,000 km” or “2,000 miles” will be shown.
●
When the driving range canno
t be measured, the display
shows “----”.
●
The driving range is shown based on the accumulated fuel consumption data, however, may be changed depending on the driving condition (road condition, driving behavior, etc.). If the battery termin
als are disconnected, the accu-
mulated fuel consumption data
will be erased. It is recom-
mended to use the indication as reference.
●
When the vehicle is fueled
, the driving range will be
updated. However, if the amount of fueling is small, the indication may not be correct. Therefore, fill up the tank as much as possible in case of fueling.
●
When the vehicle is stopped on
a steep slope, the value of
the driving range may increase.
This is caused by the fuel
movement inside the tank on the slope and is not deemedas a failure.
Resetting the driving range Press the “RESET” function button to reset the driving range plotted in graph.NOTE●
Pressing the “RESET” function button will not reset the indication (C).
●
It is possible to set the display unit to km or miles. Refer to “User customization” on page 3-46.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
24 Wednesday, January 9, 2008 4:32 PM