2008 GEELY FC Workshop Manual

Power steering--Power steering gear assembly
(b) Disassemble the screw and disconnect the fixed clamp of
in-out oil pipe assembly of power steering gear.
12. Disassemble linking lever assembly of front stabi-
lizer bar [64000097].
(a) Use socket head wrench (5mm) to fix bolt, then disas-
semble screw cap.
(b) Disassemble the left linking lever of front stabilizer liking
lever assembly.
Hint: disassemble the other with same method.
13. Disassemble the coupling bolt and nut of left/right
lower control arm ball head and control arm.
Disassemble one bolt and two nuts, and disassemble control
arm from left steering knuckle.
Hint: disassemble the other with same method.
14. Disassemble engine cover assembly
15. Support engine assembly.
16. Disassemble auxiliary automobile bracket assem-
bly [64000087]
(a) Disassemble two bolts, then disassemble side rail from
right front engine suspension.
(b) Disassemble two bolts, then disassemble carling from au-
tomobile body.
(c) Disassemble the bolt and three nuts, then disassemble
engine rear suspension from auxiliary automobile bracket.
(d) Use gearbox jack to support auxiliary automobile bracket.
(e) Disassemble four bolts and auxiliary automobile bracket
assembly with steering gear.
17. Disassemble exterior dust-proof cover of steering
column.
 206 

Power steering--Power steering gear assembly
Align the mark
18. Disassemble steering middle shaft.
(a) Make mark on middle shaft and steering small gear shaft.
(b) Disassemble bolt and steering middle shaft.
19. Disassemble power steering gear assembly
[64000133].
(a) disassemble four bolts, and disassemble power steering
gear from beam.
20. Fix power steering gear assembly [64000133].
(a) Use special tool to insure power steering gearbox assem-
bly is clamped on pliers.
Hint: affix ethylene glue on special tool before using.
21. Disassemble left transversal lever ball head.
(a) Make mark on transversal lever ball head and gear end.
(b) Loosen fixed nut, then disassemble transversal lever ball
head and fixed nut.
Hint: disassemble the other side with same method.
22. Disassemble right transversal lever ball head.
23. Check left transversal lever ball head.
(a) Insure the left transversal lever ball head is clamped on
pliers.
(b) Assemble nut on bolt.
(c) Shake the bolt of joint front and back for 4-5 times.
(d) Use torque wrench to rotate screw cap continually at the
speed of 2-4 s/r, then read the torque at fifth rotate.
Rotating torque: 0.49-3.43 N.m
Hint: check the other side with same method.
Align the mark
Ethylene
adhesive
tape
Special tool
 207 

Power steering--Power steering gear assembly
24. Check right transversal lever ball head.
25. Disassemble No.2 dust-proof cover of steering gear.
(a) Use pliers to disassemble fixed clamp.
(b) Use pliers to disassemble iron wire.
Note: do not hurt dust-proof cover.
Hint: make mark on RH and LH dust-proof cover.
Hint: disassemble the other side with same method.
26. Disassemble No.1 dust-proof cover of steering gear.
27. Disassemble terminal lever of steering gear.
(a) Use right-angled screwdriver and hammer to unclench claw
gasket.
Note: avoid knocking steering gear.
(b) Use wrench(22mm) to fix steering gear, then use special
tool to disassemble gear terminal lever.
Note: use special tool by the direction in figure.
Hint: Make mark on RH and LH gear terminal lever.
28. Assemble the parts of steering gear terminal lever.
(a) Assemble new claw gasket, and assemble gear terminal
lever temporarily.
Hint:Align pliers claw of gasket with steering gear
concave slot.
(b) Use wrench to fix steering gear, and use special tool to
tighten gear terminal lever.
Torque: 62 N
xm
Note: use special tool by the direction in figure.
Hint:use torque wrench whose lever length is 380mm.
(c) Use copper stick and hammer to concave gasket.
Note: do not hurt the steering gear.Wrench Length of
lever
Special
tool
Special tool
 208 

Power steering--Power steering gear assembly
29. Assemble steering No.2 dust-proof cover.
(a) Insure steering gear hole is not plugged by lubricating
grease.
Hint: if hole is plugged, the pressure in dust-proof
cover when steering wheel turns after combin-
ing will change.
(b) Assemble dust-proof cover, fixed clamp and new iron wire.
Note: do no t hurt or bend dust-proof cover.
(c) After coiling dust-proof cover with iron wire for two circles,
turn it for several circles to fix it.
(d) Liking that shown in figure, bend iron wire to rotating di-
rection to prevent it from hurting dust-proof cover.
Hint: assemble the other side with same method.
30. Assemble No.1 dust-proof cover of steering gear.
31. Assemble left ball head of transversal lever .
(a) Screw locking cap and transversal lever ball head in gear
terminal lever until aligning the mark.
(b) After adjusting front wiring harness, tighten the screw cap
(referring to page 80).
Torque: 74 ± 5 N
xm
Hint: assemble the other side with same method.
32. Assemble right ball head of transversal lever .
33. Assemble power steering gear assembly [64000133].
(a) Assemble power steering gear assembly on beam with
four bolts.
Torque: 58 N
xm
 209 
Align the mark

Power steering--Power steering gear assembly
34. Assemble steering middle shaft.
(a) Align the mark of steering middle shaft and steering small
gear shaft.
(b) Assemble the bolt.
Torque: 35 N
x xx x
xm
35. Assemble exterior dustproof cover of steering
column.
36. Assemble auxiliary bracket assembly (64000087).
(a) Use special tool to align the right side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt
temporarily.
(b) Use special tool to align the left side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt
temporarily.
(c) Use special tool to align the left side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt.
Torque:
A bolt: 157 ± 10 N
x xx x
xm
B bolt: 113 ± 10 N
x xx x
xm
(d) Use special tool to align the right side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt.
Torque:
A bolt: 157 ± 10 N
x xx x
xm
B bolt: 113 ± 10 N
x xx x
xm
(e) After connecting with engine with one bolt and three screw
caps, hang it to auxiliary bracket.
Torque: 52 N.m ± 5 N
x xx x
xm
(f) Assemble carling to body with two bolts.
Torque: 39 ± 3 N
x xx x
xm
(g) Assemble the front suspension of engine to carling with
two screw caps.
Torque: 52 ± 5 N
x xx x
xm
Align the mark
Special
tool
Special tool
 210 

Power steering--Power steering gear assembly
37. Connect the bolts and nuts of left/right control arm
and control arm ball head.
Torque: 142 ± 10 Nx xx x
xm
Hint: connect the other side with same method.
Connect left lower control arm to steering knuckle with
bolt and two nuts.
38. Connect linking lever assembly of left/right front
stabilizer bar [64000097].
Use socket head wrench (5mm) to fix bolt, then connect sta-
bilizer linking lever with screw cap.
Torque: 74 ± 5 N
x xx x
xm
Hint: connect the other side with same method.
39. Connect the in-out oil pipe assembly of power steer-
ing gear [64000131].
(a) Connect the in-out oil pipe fixed clamp of power steering
gear with bolt.
Torque: 7.8 N
x xx x
xm
(b) Use special tool to connect the in-out oil pipe assembly of
power steering gear.
Torque: 41 N
x xx x
xm
Hint:
zUse the torque wrench whose lever length is
345mm.
zSpecial tool should be parallel with torque wrench,
only this could make practical torque value.
Hint: connect the other side with same method.
40. Connect the ball head at the left side of transversal
lever.
(a) Connect the ball head at the left side of transversal lever
with screw cap.
Torque: 49 ± 5 N
x xx x
xm
(b) Assemble new cotter pin.
Note: if cotter pin hole could not be aligned , tighten
the screw cap for 60 again.
Hint: connect the other side with same method.
 211 
Length of lever

Power steering--Power steering gear assembly
41. Connect the ball head at the right side of transver
sal lever .
42. Assemble right bottom defending board of engine
[68000004].
43. Assemble left bottom defending board of engine
[68000003].
44. Assemble front wheel
Torque: 103 ± 10 Nx xx x
xm
45. Connect steering slide shaft assembly.
(a) Align the mark between steering middle shaft and sliding
shaft.
(b) Assemble B bolt.
Torque: 35 ± 3 N
x xx x
xm
(c) Tighten the A bolt.
Torque: 35 ± 3 Nx xx x
xm
46. Assemble inner dustproof cover of steering column [64000123].
Assemble inner dustproof cover of steering column with two screw caps.
47. Make front wheel face the front
Hint: lift up front wheel shaft.
48. Assemble helix cable assembly (equipping with SRS).
49. Assemble steering wheel assembly [67010001].
(a) Align the mark between steering wheel and main shaft of steering column.
(b) Lock the fixed screw cap of steering wheel temporarily.
50. Add power steering oil (referring to page 200).
51. Exhaust the air in power steering system (referring to page 200).
52. Check the central point of steering wheel.
(a) Check the central point of steering wheel.
(b) Lock the fixed screw cap of steering wheel.
Torque: 50 ± N
x xx x
xm
53. Assemble safety airbag assembly at the side of driver (equipping with SRS) [67010011].
54. Check whether there is oil leakage.
55. Check the engine cover assembly.
56. Adjust the engine cover assembly.
57. Check and adjust the front wheel alignment (referring to page 87).
 212 

Air conditioner--Air conditioning system
Air conditioner
Air conditioning system
Note
1. Do not dispose Refrigerant in sealed space or near
flame.
2. Wear glasses to protect your eyes.
3. Do not let liquid Refrigerant contact with your eyes
or skin.
If liquid Refrigerant contacts with your eyes or skin:
(a) Wash the contacted part with much water.
Warning: do not knead your eyes or skin.
(b) Spread clean Vaseline on your skin.
(c) Go to doctor or hospital for special cure.
4. Forbid heating it or making it expose the flame.
5. Forbid dropping the Refrigerant tank or shake it
intensively.
6. Do not operate compressor when Refrigerant is lack.
If the Refrigerant in cooling system is lack, it will incur com-
pressor burned out for lacking lubrication. So it is necessary
to avoid.
7. Do not open the high pressure valve of filling instru-
ment package when compressor is working.
If opening the valve at this time, Refrigerant will flow back into
refrigerant tank to incur the tank will break. So only the low
pressure valve could be opened or closed.
8. Do not fill Refrigerant too much.
Too much refrigerant will make many problems such as lack
cooling degree, oil consumption, too hot engine and so on.
Inspection on automobile
1. Check the No.1 pressure switch.
(a) Control for electromagnetic clutch:
Check the function of pressure switch.
(1) Assembly filling instrument package.
(2) Connect the anode lead of OUM meter to No. 4 termi-
nal and connect cathode lead to No. 1 terminal.
(3) Liking that shown in figure. When refrigerant pressure
is changed, check the conduction between terminals.
wrong correct
Low-pressure
sideHigh-pressure
side
Not
conductionCon-
duction
Not
conduction
 213