2008 GEELY FC Workshop Manual

Change
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction.
zPlease refer to subassembly figure of rear bumper on page 381.
Exterior/inner trim board--Rear bumper
 382  1. Disassemble trunk carpet assembly [68000114]
2. Disassemble rear trim board of trunk [68000118]
(a) Use two fixing clasps.
(b) Use disassembling tool for trim tape to disassemble rear
trim board of trunk.
3. Disassemble left decoration of trunk [68000112]
(a) Use disassembling tool for fixing clamp to disassemble
fixing clamp and a part of left decoration of trunk.
Hint:
Disassemble the fixing clasp and left decoration of trunk in the scope of screw cap used for
fixing rear bumper and trunk which could be disassembled.
4. Disassemble right decoration of trunk [68000113]
5. Disassemble mudguard of left rear wheel [68000223]
(a) Disassemble two screws and mudguard of left rear wheel.
6. Disassemble mudguard of right rear wheel [68000224]
7. Disassemble trim board of left rear wheel [68000230]
(a) Use screw driver to disassemble fixing clasp from rear bumper.
(b) Use disassembling tool for fixing clasp to disassemble fix-
ing clasp.
(c) Disassemble trim board of left rear wheel.
Hint: Disassemble trim board of left rear wheel in the
scope of screw used for fixing rear bumper which could
be disassembled.
8. Disassemble trim board of right rear wheel [68000231]
9. Disassemble rear bumper [68000012]
(a) Use screw driver to disassemble two fixing clasps.
(b) Disassemble four screw caps and two screws.
(c) Disassemble fixing clasp and rear bumper.
(d) Equipping with radar probe head: disassemble four joints of
radar probe head.
10. Disassemble reversing radar probe head assembly.
(a) Disassemble fixing pedestal of radar probe and radar probe.
11. Disassemble left rear fog light assembly [67000100]
(a) Disassemble fixing nut and left rear fog light assembly.
12. Disassemble right rear fog light assembly [67000101]

Exterior/inner trim board--Rear bumper
Nameplate
Change
1. No.2 nameplate of trunk cover
2. No.3 nameplate of trunk cover3. No.6 nameplate of trunk cover
4. Nameplate of front wing board
1 2
3
China-
Geely
 383 

Exterior/inner trim board--Exterior seal tape of left front door glass
Exterior seal tape of left front door glass (LH)
Change
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction.
zChanging procedure for right side is same as left side.
protective
adhesive tape
 384  1. Disassemble exterior seal tape of left front door
glass [68000158]
(a) Affix protective adhesive tape to the lower part of exterior
seal tape of left front door glass.
(b) Use disassembling tool or scraper for trim tape to disas-
semble exterior seal tape of left front door glass.
Hint: before using scraper, the needled top of scraper
should be twisted with adhesive tape.

Exterior/inner trim board--Exterior seal tape of left rear door glass
Exterior seal tape of left rear door glass
Change
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction.
zChanging procedure for right side is same as left side.
Protective
adhesive tape
 385  1. Disassemble exterior seal tape of left rear door glass
[68000196]
(a) Affix protective adhesive tape to the lower part of exterior
seal tape of left rear door glass.
(b) Use disassembling tool or scraper for trim tape to disas-
semble exterior seal tape of left rear door glass.
Hint: before using scraper, the needled top of scraper
should be twisted with adhesive tape.

Exterior/inner trim board--Light fender
Light fender
Change
1. Disassemble locker core and pedestal of trunk.
2. Disassemble number plate light defender [68000107]
Disassemble four screw caps, then disassemble the defender.
3. Assemble rear logo assembly [61000019]
(a) Use white gasoline to clean the assembling surface of logo.
(b) Use heating light to heat defender and logo.
(c) Assemble the logo.
Note:do not heat logo excessively
2 Fixing clamp
 386 

Exterior/inner trim board--Top left trim tape
Top left trim tape
Change
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction.
zChanging procedure for right side is same as left side.
1. Disassemble top left trim tape [68000128]
(a) Use protective adhesive tape to affix around the trimtape.
(b) Use disassembling tool for trim tape to release the front and
rear fixing clamp of trim tape, then disassemble top left trim
tape.
Note:
zDo not disassemble fixing clamp.
zIf fixing clamp is damaged when disassembling,
change it with new one.
2. Assemble top left trim tape [68000128]
Note: when only changing fixing clamp.
(a) Disassemble adhesive tape remaining on the surface of
body affixed trim tape, then use white gasoline to clean the
surface.
(b) Use heating light to heat the assembling surface of fixing
clamp and automobile body.
Automobile body: 40-60°C.
Trimtape: 20-30°C.
Note: do not heat the trim tape and body too much.
(c) Put the fixing clamp on the position shown in figure, then
press it into position with hand.
(d) After pressing the fixing clamp into position for over 30
minutes, then assemble top left trimtape.
Hint:
zSurface induration time: 30 minutes.
zComplete induration time: 24 hours.
 387 

Exterior/inner trim board--Left lower fender of automobile body
Left lower fender of automobile body (LH)
Subassembly
 388 
Lower fender
Mudguard of
left front wheel
Fixing clasp

Exterior/inner trim board--Left lower fender of automobile body
Change
Hint:
When assembling, please work by the sequence which is opposite with disassembling sequence;
if necessary, it will have assembling instruction..
Changing procedure for right side is same as the left side.
Please refer to the subassembly figure of body left lower fender on page 388.
 389  1. Disassemble mudguard of left front wheel [68000221]
(a) Disassemble three screws and mudguard of left front wheel.
2. Disassemble body left lower fender [68000049]
(a) Use disassembling tool for fixing clamp to disassemble eight
fixing clamps.
(b) Disassemble the screw.
(c) Use disassembling tool for trim tape to disassemble body
left lower fender.