2008 GEELY FC Workshop Manual

Anti-stealing and door lock--Electric door lock control system
Malfunction phenomenon
“Door locker control system” does not work
(all).
Door locking/unlocking malfunction (use
handle operation and key operation)
Door locking/unlocking malfunction (use
key)
Malfunction of key keeping protection func-
tion
Only one door locker does not workPossible malfunction part
1. DOOR fuse (panel J/B)
2. Wiring harness
1. Electric window main switch (door control switch)
2. Wiring harness
1.
Door at the side of driver assembly (door control switch)
2. Wiring harness
3. Door locker connecting rod is loosen
1. Anti-versa lock supervising switch
2. Door control light switch
3. Wiring harness
1. Door locker electric motor
2. Wiring harnessReferred page
-
-
359
-
359
-
-
359
-
-
359
-
Malfunction phenomenon table
 358 

Anti-stealing and door lock--Electric door lock control system
Inspection
1. Check driver sear door locker assembly.
(a) Liking that shown in figure, check the conduction of every
terminal of door key switch.
If the conduction does not accord with the regulation, change
the switch.
(b) Liking that shown in figure, supply battery voltage to terminal,
and check the function of door locker.
If the function does not accord with the regulation, change
the door locker assembly.
Open Close
Open Close
 359 
Position of switch Terminal connected by avometerRegulated situation
LOCK 2-4Conduction
OFF - Not conduction
UNLOCK 1-2-3 Conduction
Condition Function
Supply battery anode to No. 6 terminal, cathode to No.5 terminalOpen
Supply battery anode to No. 5 terminal, cathode to No.6 terminalClose

Anti-stealing and door lock--Electric door lock control system
2. Check front passenger seat door locker assembly
Liking that shown in figure, supply battery voltage to terminal,
and check the function of door locker.
If the function does not accord with the regulation, change the
door locker assembly.
3. Check the left rear and right rear door locker assembly.
Liking that shown in figure, supply battery voltage to terminal,
and check the function of door locker.
If the function does not accord with the regulation, change the
door locker assembly.
OpenClose
Open
Close
 360 
Condition Function
Supply battery anode to No. 6 terminal, cathode to No.5 terminalOpen
Supply battery anode to No. 5 terminal, cathode to No.6 terminalClose
Condition Function
Supply battery anode to No. 6 terminal, cathode to No.5 terminalOpen
Supply battery anode to No. 5 terminal, cathode to No.6 terminalClose

Anti-stealing and door lock--Electronic anti-stealing system
Electronic anti-stealing system
Electronic anti-stealing system consists of anti-stealing controller, anti-stealing loop and transmitter. One
end of loop covers ignition locker core, the other end connects with anti-stealing controller, and the other end
of controller connects with engine ECU, at the same time, transmitter is assembled in key. Memory of
transmitter stores only mark (code) showing the legal identity of automobile owner, transmitter, anti-stealing
controller and electric injection ECU constitutes a multi-layer effective electronic anti-stealing system verified
by password.
If customer key loses, anti-stealing ECU is changed or engine ECU is changed, it is necessary to match
again in repairing station. When automobile leaves the factory, safety password is delivered directly to
owner for keeping with the type of secrecy. If it is necessary to make a new key, change anti-stealing
controller and make other operations, owner should bring the safety password with the automobile to repair
in repairing station. Repairing station should keep repairing (make new key, change anti-stealing controller
and so on) record for inquiring in future.
 361 

Electric sunroof (optional)--Sunroof
Bolt
Screw cap
Electric sunroof (optional)
Sunroof
Overhaul
Hint: when assembling, please work by the sequence which is opposite with disassembling
sequence; but when it has items that need to pay special attention, it will add special specification.
1. Disassemble inner trim board of top (referring to page 390).
2. Disassemble the glass of sunroof.
(a) Use planetary wrench to disassemble planetary screw.
(b) Pull the glass upwards to disassemble it.
3. Disassemble waterproof adhesive tape of sunroof.
4. Disconnect connection of wiring harness.
5. Disassemble shell body of sunroof.
(a) Disassemble four drain hoses.
(b) Liking that shown in figure, disassemble four bolts and six screw caps, then disassemble shell body.
6. Disassemble trim sun shade of sunroof.
(a) Disassemble the screw and stopper.
(b) Disassemble trim sun shade of sunroof.
 362 

Electric sunroof (optional)--Sunroof
7. Use screw driver (twisted by adhesive tape) to align
the sunroof driving pull cable with right mark.
8. Assemble sunroof shell body assembly.
(a) Bolt.
Torque: 5.5 N
⋅ ⋅⋅ ⋅
⋅m
(b) Screw cap.
Torque: 5.0 N
⋅ ⋅⋅ ⋅
⋅m
9. Assemble the glass of sunroof.
(a) Check the phase difference between sunroof waterproof ad-
hesive tape and top gasket.
Front end and rear end: 0±1.5mm
Rear corner: 0±1.5mm
0-1.5mm
(b) Adjustment
Use T25 planetary wrench to loosen the screw to adjust
the sunroof on correct position, then lock the screw.
10. Inspection for water leakage.
(a) After the adjustment, check whether the sunroof leaks water.
(b) If sunroof leaks water, adjust it again.
Assembly mark
 363 

Electric sunroof (optional)--Sunroof system
Inspection for sunroof function
1. Inspection for sliding opening function.
(1) Turns ignition switch to ON, when spot contacting sunroof
switch keystroke 2, the sunroof will start automatic sliding
opening work, and it does not stop until it is at complete
opening state. If spot contacting it in running process, or
pressing keystroke 1 or 2 for long time, sunroof glass will
stop running immediately.
(2) Turns ignition switch to ON, when pressing keystroke 2 for
Sunroof system
Specification for sunroof function
1. Operation category
Spot contact: press the keystroke one time, then release immediately (the time is less than 0.3 seconds).
Long press: press the key stroke for long time (the time is more than 0.3).
2. Specification for function.
Anti-clamping function: spot contact the keystroke to make the sunroof could face 10 Kg resistance in the
process of closing from any position, at this time, electric motor turns oppositely, and the sunroof returns
turn-up or opening state.
Automatic closing function: when the key is pulled out from ignition locker, at this time, the sunroof is not
at closing state, it will close automatically in three seconds.
long time, the sunroof will start automatic sliding opening work, and it does not stop until it is at
complete opening state. If releasing keystroke 2 in running process, the sunroof glass will stop running
immediately.
2. Inspection for sliding closing function.
(1) Turns ignition switch to ON, if the sunroof is at opening state, when spot contacting sunroof switch
keystroke 1, the sunroof will automatically slide to closing state. If spot contacting it or pressing
keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at opening state, when pressing sunroof switch keystroke
1 for long time, the sunroof will automatically slide to closing state. If releasing keystroke 1 in running
process, sunroof glass will stop running immediately.
3. Inspection for turn-up opening function
(1) Turns ignition switch to ON, if the sunroof is at closing state, when spot contacting sunroof switch
keystroke 1, the sunroof will automatically move to turn-up opening state. If spot contacting it again or
pressing keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at closing state, when pressing sunroof switch keystroke
1 for long time, the sunroof will automatically slide to turn-up opening state. If releasing keystroke 1 in
running process, sunroof glass will stop running immediately.
4. Inspection for turn-up closing function
(1) Turns ignition switch to ON, if the sunroof is at turn-up opening state, when spot contacting sunroof
switch keystroke 2, the sunroof will automatically move to closing state. If spot contacting it again or
pressing keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at turn-up opening state, when pressing sunroof switch
keystroke 2 for long time, the sunroof will automatically slide to closing state. If releasing keystroke 2
in running process, sunroof glass will stop running immediately.
 364 
Front
Rear

Electric sunroof (optional)--Sunroof system
Inspection for sunroof switch
(a) Check the function of switch. Disassemble front top light,
and disassemble the joint of front top light, then check the
joint at the side of switch liking that shown in figure.
Malfunction phenomenon table Position of parts
Malfunction phenomenon
Sunroof system does not work
Sunroof system works abnormallyPossible malfunction part
1. Ignition switch.
2. Control switch of sunroof.
3. 25A, 15# fuse.
4. Wiring harness
1. Control switch of sunroof.
2. Wiring harnessReference page
-
-
-
-
-
-
 365 
Terminal connected by avometer
2-4
2-5ConditionSpot contact or press
keystroke 2 for long time
Spot contact or press
keystroke 1 for long time
Regulated situa-
tion
Conduction
Conductiion
Shell body of sunroof
Motor of sunroof
Switch of sunroof