2006 DODGE RAM SRT-10 seats

5. Fold the seat backs forward and roll the seat
assembly back in the vehicle.
6. Remove and discard the nuts (2 and 4) on either
the driver or passenger side.
7. Separate the seat assembly by removing and dis-
carding the nuts (4) on either the drivers or pas-
sengers seat.
8. Remove each section of the seat assembly from
the vehicle.
INSTALLATION
1. Before proceeding with the following repair proce-
dure, review all warnings and cautions. (Refer to
23 - BODY/SEATS - WARNING)
NOTE: Do not reuse the seat fasteners, always
replace with new ones.
2. Position each seat section into the vehicle and tip
back.
3. Install the nuts (4) attaching the center seat section
(2) to the other seat, and tighten to 25 Nꞏm (18 ft.
lbs.).

4. Install the nuts (2 and 4) attaching the center seat
section to the other seat, and tighten to 25 Nꞏm (18
ft. lbs.).
5. Connect the electrical connectors (1).
6. Roll the seat assembly forward and install new rear
bolts (2). Tighten the bolts (2) to 40 Nꞏm (30 ft.
lbs.).
7. Fold the seat backs up and slide the seats (1) to
the rear.
8. Install new front bolts (4) and tighten to 28 Nꞏm (21
ft. lbs.).

SEAT BACK CUSHION / COVER - FRONT
REMOVAL
1. Remove the front seat (Refer to 23 - BODY/SEATS/SEAT - FRONT - REMOVAL).
2. Remove the lumbar handle and bezel (if equipped) (Refer to 23 - BODY/SEATS/LUMBAR SUPPORT HANDLE/
BEZEL - REMOVAL).
3. Remove the headrest sleeves (Refer to 23 - BODY/SEATS/HEADREST SLEEVE -REMOVAL).
4. Unzip the zip strip at the lower end of the seat back and remove the seat back cover and cushion.
INSTALLATION
1. Install the seat back cushion and cover onto the seat frame assembly.
2. Connect the zip strip at the bottom of the seat back.
3. Install the headrest sleeves. (Refer to 23 - BODY/SEATS/HEADREST SLEEVE-INSTALLATION)
4. Install the lumbar bezel and handle, if equipped. (Refer to 23 - BODY/SEATS/LUMBAR SUPPORT HANDLE/
BEZEL - INSTALLATION)
5. Install the seat. (Refer to 23 - BODY/SEATS/SEAT - FRONT - INSTALLATION)

SEAT CUSHION / COVER - FRONT
REMOVAL
1. Remove the front seat. (Refer to 23 -BODY/SEATS/SEAT - FRONT - REMOVAL)
2. Remove the screw and remove the recliner handle.
3. Remove the two screws and remove the power seat controls, if equipped, and disconnect the electrical connec-
tor.
4. Disconnect the j-straps and remove the seat cushion and cover.
INSTALLATION
1. Position the seat cushion and cover onto the frame assembly and connect the j-straps.
2. Connect the power seat control switch electrical connector, if equipped.
3. Install the power seat control switch and install the two screws, if equipped.
4. Install the recliner handle and install the screw.
5. Install the front seat. (Refer to 23 - BODY/SEATS/SEAT - FRONT - INSTALLATION)

SEAT RISER - FRONT
REMOVAL
1. Remove the front seat. (Refer to 23 -BODY/SEATS/SEAT - FRONT - REMOVAL)
2. Disconnect the heated seat electrical connectors, if equipped.
3. Remove the four nuts attaching the seat track to the seat and remove the track.
INSTALLATION
1. Position the seat track onto the seat and install the four nuts.
2. Tighten the four nuts to 25 Nꞏm (18 ft. lbs.).
3. Connect the heated seat electrical connectors, if equipped.
4. Install the seat. (Refer to 23 - BODY/SEATS/SEAT - FRONT - INSTALLATION)

SEAT - REAR
REMOVAL
1. Remove the load floor (Refer to 23 - BODY/INTE-
RIOR/LOAD FLOOR - REMOVAL).
2. Fold the rear seat cushions up and remove the
rear bolts (1, 3, and 5).
3. Lift each seat assembly up and disengage the seat
back frame hooks (1 and 3) from the footmans
loops (2 and 4) bolted to the rear cab back.
4. Remove the seats from the vehicle.

INSTALLATION
1. Install the seats into the vehicle and engage the
seat back frame hooks (1 and 3) with the footmans
loops (2 and 4) in the cab back panel.
2. Install the rear seat bolts (1, 3, and 5) and tighten
to 40 Nꞏm (30 ft. lbs.).
3. Install the load floor (Refer to 23 - BODY/INTERI-
OR/LOAD FLOOR - INSTALLATION).

SEAT BACK - REAR
REMOVAL
1. Remove the rear seat (Refer to 23 - BODY/SEATS/
SEAT - REAR - REMOVAL).
2. Remove the seat back bolts (1) and remove the
seat back (4).
INSTALLATION
1. Install the seat back (4) and install the bolts (1).
2. Tightenthebolts(1)to25Nꞏm(18ft.lbs.).
3. Install the rear seat (Refer to 23 - BODY/SEATS/
SEAT - REAR - INSTALLATION).