2006 DODGE RAM SRT-10 seats

3. Remove the bolts (1) and lift the rear of the base
up to release the front guide pins (5).
4. Remove the front base (2).
NOTE: Do not reuse the seat fasteners, always
replace with new ones.
5. Remove and discard the front bolts (4).
6. Position the seats forward, remove the rear bolts
(2) and discard.
7. Disconnect the 12v power supply electrical connec-
tor (3 - if equipped).
8. Fold the seat backs forward and roll the seat
assembly (1) back in the vehicle.
9. Remove the nuts (2) attaching the center seat con-
sole (1) to the drivers seat and the passenger seat
and discard.

Full Floor Console
1. Before proceeding with the following repair proce-
dure, review all warnings and cautions. (Refer to
23 - BODY/SEATS - WARNING)
NOTE: Do not reuse the seat fasteners, always
replace with new ones.
2. Position the center seat console onto the front seat
assembly and roll the seat assembly back in the
vehicle.
3. Install new nuts (4) attaching the center console to
the drivers (3) and passenger seat.
4. Connect the electrical connector (1 - if equipped).
5. Tighten the nuts (4) to 25 Nꞏm (18 ft. lbs.).
6. Install new nuts (2) attaching the center console (1)
to the drivers and passenger seat.
7. Tightenthenutsto25Nꞏm(18ft.lbs.).
8. Connect the electrical connector (3 and 5 - if
equipped).
9. Roll the seat assembly forward and install new rear
bolts (2).
10. Connect the 12v power supply electrical connec-
tor (3 - if equipped).
11. Tighten the rear bolts to 40 Nꞏm (30 ft. lbs.).
12. Fold the seat backs up and slide the seats to the
rear.
13. Install new front bolts (4) and tighten to 28 Nꞏm
(21 ft. lbs.).

page page
SEATS
WARNING
WARNINGS - RESTRAINT SYSTEM . . ....... 222
CENTER SEAT
REMOVAL ................................... 223
INSTALLATION .............................. 224
CENTER ARMREST / SEAT BACK
REMOVAL ................................... 225
INSTALLATION .............................. 225
CENTER SEAT BACK INERTIA HINGE COVER
REMOVAL ................................... 226
INSTALLATION .............................. 227
CENTER SEAT BACK HINGE
REMOVAL ................................... 228
INSTALLATION .............................. 230
CENTER SEAT BACK LID
REMOVAL ................................... 232
INSTALLATION .............................. 232
CENTER SEAT CUSHION
REMOVAL ................................... 233
INSTALLATION .............................. 233
CENTER SEAT CUSHION COVER
REMOVAL ................................... 234
INSTALLATION .............................. 234
HEADREST
REMOVAL ................................... 235
INSTALLATION .............................. 235
HEADREST SLEEVE
REMOVAL ................................... 236
INSTALLATION .............................. 236
SEAT - FRONT
REMOVAL ................................... 237
INSTALLATION .............................. 238
SEAT BACK CUSHION / COVER - FRONT
REMOVAL ................................... 240
INSTALLATION .............................. 240
LUMBAR SUPPORT HANDLE/BEZEL
REMOVAL ................................... 241INSTALLATION .............................. 241
SEAT CUSHION / COVER - FRONT
REMOVAL ................................... 243
INSTALLATION .............................. 243
SEAT RISER - FRONT
REMOVAL ................................... 244
INSTALLATION .............................. 244
SEAT - REAR
REMOVAL ................................... 245
INSTALLATION .............................. 246
SEAT BACK - REAR
REMOVAL ................................... 247
INSTALLATION .............................. 247
SEAT BACK CUSHION / COVER - REAR
REMOVAL ................................... 248
INSTALLATION .............................. 248
SEAT CUSHION / COVER - REAR
REMOVAL ................................... 249
INSTALLATION .............................. 249
SEAT CUSHION FRAME - REAR
REMOVAL ................................... 250
INSTALLATION .............................. 250
UNDER SEAT STORAGE BIN LID
REMOVAL ................................... 251
INSTALLATION .............................. 251
UNDER SEAT STORAGE BIN
REMOVAL ................................... 252
INSTALLATION .............................. 252
UNDER SEAT STORAGE BIN COVERING
REMOVAL ................................... 253
INSTALLATION .............................. 253
UNDER SEAT STORAGE BIN LATCH
REMOVAL ................................... 254
INSTALLATION .............................. 254
SEAT BACK REAR - FOOTMANS LOOP
BRACKETS
REMOVAL ................................... 255
INSTALLATION .............................. 255

SEATS
WARNING
WARNINGS - RESTRAINT SYSTEM
WARNING: To avoid personal injury or death, during and following any seat beltorchildrestraintanchor
service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors
for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any
belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or ineffective buckle
or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child
restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to
repair a seat belt or child restraint component. Always replace damaged orineffective seat belt and child
restraint components with the correct, new and unused replacement parts listed in the DaimlerChrysler
Mopar
Parts Catalog.
WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental
restraint system before attempting any steering wheel, steering column,airbag, seat belt tensioner, impact
sensor, or instrument panel component diagnosis or service. Disconnect and isolate the battery negative
(ground) cable, then wait two minutes for the system capacitor to discharge before performing further diag-
nosis or service. This is the only sure way to disable the supplemental restraint system. Failure to take the
proper precautions could result in accidental airbag deployment.
WARNING: To avoid personal injury or death on vehicles equipped with airbags, before performing any
welding operations disconnect and isolate the battery negative (ground)cable and disconnect all wire har-
ness connectors from the Occupant Restraint Controller (ORC). Failure totake the proper precautions could
result in accidental airbag deployment and other possible damage to the supplemental restraint system cir-
cuits and components.
WARNING: To avoid personal injury or death, do not attempt to dismantle an airbag unit or tamper with its
inflator. Do not puncture, incinerate, or bring into contact with electricity. Do not store at temperatures
exceeding 93° C (200° F). An airbag inflator unit may contain sodium azide and potassium nitrate. These
materials are poisonous and extremely flammable. Contact with acid, water, or heavy metals may produce
harmful and irritating gases (sodium hydroxide is formed in the presence of moisture) or combustible com-
pounds. An airbag inflator unit may also contain a gas canister pressurizedtoover2500psi.
WARNING: To avoid personal injury or death, when handling a seat belt tensioner retractor, proper care
should be exercised to keep fingers out from under the retractor cover and away from the seat belt webbing
where it exits from the retractor cover.
WARNING: To avoid personal injury or death, replace all restraint system components only with parts spec-
ified in the DaimlerChrysler Mopar
Parts Catalog. Substitute parts may appear interchangeable, but internal
differences may result in inferior occupant protection.
WARNING: To avoid personal injury or death, the fasteners, screws, and bolts originally used for the
restraint system components must never be replaced with any substitutes.These fasteners have special
coatings and are specifically designed for the restraint system. Any timea new fastener is needed, replace
it with the correct fasteners provided in the service package or specifiedin the DaimlerChrysler Mopar
Parts Catalog.
WARNING: To avoid personal injury or death, when a steering column has an airbag unit attached, never
place the column on the floor or any other surface with the steering wheel orairbag unit face down.

CENTER SEAT
REMOVAL
1. Before proceeding with the following repair proce-
dure, review all warnings and cautions. (Refer to
23 - BODY/SEATS - WARNING)
NOTE: Do not reuse the seat fasteners, always
replace with new ones.
2. Remove and discard the front bolts (4).
3. Position the seats forward, remove the rear bolts
(2) and discard.
4. Disconnect the 12v power supply electrical connec-
tor (3 - if equipped).
5. Fold the seat backs forward and roll the seat
assembly (1) back in the vehicle.
6. Remove the nuts (2 and 4) attaching the center
seat (1) to the drivers seat and the passenger seat
and discard.
7. Remove the nuts (4) attaching the center seat (2)
to the drivers seat (3) and the passenger seat in
the rear of the seat and discard.
8. Disconnect the electrical connector (1 - if
equipped).
9. Roll the seat assembly forward and remove the
center seat portion.

INSTALLATION
1. Before proceeding with the following repair proce-
dure, review all warnings and cautions. (Refer to
23 - BODY/SEATS - WARNING)
NOTE: Do not reuse the seat fasteners, always
replace with new ones.
2. Install the center seat (2) and roll the seat assem-
bly back in the vehicle.
3. Install new nuts (4) attaching the center seat to the
drivers (3) and passenger seat.
4. Connect the electrical connector (1 - if equipped).
5. Tighten the nuts (4) to 25 Nꞏm (18 ft. lbs.).
6. Install new nuts (2 and 4) attaching the center seat
(1) to the drivers and passenger seat.
7. Tighten the nuts (4) to 25 Nꞏm (18 ft. lbs.).
8. Connect the electrical connector (3 and 5 - if
equipped).
9. Roll the seat assembly forward and install new rear
bolts (2).
10. Connect the 12v power supply electrical connec-
tor (3 - if equipped).
11. Tighten the rear bolts to 40 Nꞏm (30 ft. lbs.).
12. Fold the seat backs up and slide the seats to the
rear.
13. Install new front bolts (4) and tighten to 28 Nꞏm
(21 ft. lbs.).

CENTER ARMREST / SEAT BACK
REMOVAL
1. Before proceeding with the following repair proce-
dure, review all warnings and cautions. (Refer to
23 - BODY/SEATS - WARNING)
NOTE: Do not reuse the seat fasteners, always
replace with new ones.
2.Removethecenterseat(Referto23-BODY/
SEATS/SEAT - CENTER - REMOVAL).
3. Disconnect the storage bin/cushion cover j-straps
and position aside.
4. Remove and discard the hinge bolts (2) and sepa-
rate the seat back from the storage bin/cushion (1).
INSTALLATION
1. Before proceeding with the following repair proce-
dure, review all warnings and cautions. (Refer to
23 - BODY/SEATS - WARNING)
NOTE: Do not reuse the seat fasteners, always
replace with new ones.
2. Install the seat back onto the storage bin/cushion
(1) and install new hinge bolts (2).
3. Tighten the hinge to storage bin/cushion bolts (2) to
25 Nꞏm (18 ft. lbs.).
4. Connect the storage bin/cushion cover j-straps.
5. Install the center seat (Refer to 23 - BODY/SEATS/
SEAT - CENTER - INSTALLATION).

CENTER SEAT BACK INERTIA HINGE COVER
REMOVAL
NOTE: Free pivot hinge cover is removed with the
free pivot hinge (Refer to 23 - BODY/SEATS/CEN-
TER SEAT BACK HINGE - REMOVAL).
1. For the inertia hinge cover disconnect the zip strip
(1).
2. Position aside the storage bin/cushion cover (4).
3. Remove the pivot bolt (5).
4. Open the hinge cover at the bottom and remove
the hinge cover (1).