2006 DODGE RAM SRT-10 seats

SEAT BACK CUSHION / COVER - REAR
REMOVAL
1. Remove the rear seat back. (Refer to23 - BODY/SEATS/SEAT BACK - REAR - REMOVAL)
2. Remove the headrest sleeves. (Refer to 23 - BODY/SEATS/HEADREST SLEEVE- REMOVAL)
3. Unzip the zip strip at the bottom of the seat back and remove the cover.
INSTALLATION
1. Install the seat back cover and connect the zip strip.
2. Install the headrest sleeves. (Refer to 23 - BODY/SEATS/HEADREST SLEEVE-INSTALLATION)
3. Install the seat back. (Refer to 23 - BODY/SEATS/SEAT BACK - REAR - INSTALLATION)

SEAT CUSHION / COVER - REAR
REMOVAL
1. Remove the rear seat. (Refer to 23- BODY/SEATS/SEAT - REAR - REMOVAL)
2. Separate the zip strip at the rear of the seat cushion and remove the cushion and cover.
INSTALLATION
1. Install the seat cushion and cover over the cushion frame assembly and connect the zip strip.
2. Install the seat. (Refer to 23 - BODY/SEATS/SEAT - REAR - INSTALLATION)

SEAT CUSHION FRAME - REAR
REMOVAL
1. Remove the seat cushion/cover (Refer to 23 -
BODY/SEATS/SEAT CUSHION/COVER - REAR -
REMOVAL).
2. Remove the bolts (3) and remove the seat cushion
frame (2).
INSTALLATION
1. Install the seat cushion frame (2) onto the rear seat
cushion hinges (4).
2. Install the bolts (3) and tighten to 85 Nꞏm (63 ft.
lbs.).
3. Install the seat cushion/cover (Refer to 23 - BODY/
SEATS/SEAT CUSHION / COVER - REAR -
INSTALLATION).

UNDER SEAT STORAGE BIN
REMOVAL
1. Remove the amplifier, if equipped.(Refer to 8 - ELECTRICAL/AUDIO/AMPLIFIER - REMOVAL)
2. Remove the center seat cushion. (Refer to 23 - BODY/SEATS/CENTER SEAT CUSHION - REMOVAL)
3. Remove the six screws and remove the bin.
INSTALLATION
1. Install the bin over the seat cushion hinges and install the six screws.
2. Install the center seat cushion. (Refer to 23 - BODY/SEATS/CENTER SEAT CUSHION - INSTALLATION)
3. Install the amplifier, if equipped. (Refer to 8 - ELECTRICAL/AUDIO/AMPLIFIER - INSTALLATION)

UNDER SEAT STORAGE BIN COVERING
REMOVAL
1. Remove the under seat storage bin. (Refer to 23 - BODY/SEATS/UNDER SEAT STORAGE BIN - REMOVAL)
2. Disconnect the j-straps and remove the cover.
INSTALLATION
1. Install the storage bin cover and connect the j-straps.
2. Install the under seat storage bin. (Refer to 23 - BODY/SEATS/UNDER SEATSTORAGE BIN - INSTALLATION)

SEAT BACK REAR - FOOTMANS LOOP BRACKETS
REMOVAL
1. Remove the rear seat (Refer to 23 - BODY/SEATS/
SEAT - REAR - REMOVAL).
2. Remove bolts (2) and remove the loop (1).
INSTALLATION
1. Install the loop (1) and install the bolts (2).
2. Tighten the bolts (2) to 12 Nꞏm (9 ft. lbs.).
3. Install the seat (Refer to 23 - BODY/SEATS/SEAT -
REAR - INSTALLATION).

BACKLITE VENT GLASS - REGULATOR
REMOVAL
1. Disconnect and isolate the battery negative cable.
2. Remove the rear seats (Refer to 23 - BODY/SEATS/SEAT - REMOVAL).
3. Remove the rear cab back panel (Refer to 23 - BODY/INTERIOR/REAR CAB BACKPANEL TRIM - REMOVAL).
4. Remove the two mounting bolts (1).
5. Disconnect the electrical connector to the power
motor.
6. Separate the cable housings from the glass track
(1).
7. Disconnect the cable ends from the vent glass (2).
8. Separate the support clips (5) and remove the reg-
ulator assembly (3).

INSTALLATION
1. Connect the cable ends to the vent glass (2).
2. Install the cable housings into the glass tracks (1).
3. Fasten the support clips (5).
4. Install the 2 mounting bolts (1).
5. Install the rear cab back panel (Refer to 23 -
BODY/INTERIOR/REAR CAB BACK PANEL TRIM
- INSTALLATION).
6. Install the rear seats (Refer to 23 - BODY/SEATS/
SEAT - INSTALLATION).
7. Connect the battery negative cable.