1998 HONDA INTEGRA Workshop Manual

Doors
Glass/Regulator/Glass Run Channel Replacement
Remove:
a Door panel (see page 2O-4)
a Plastic cover (see page 20 4)
Remove the power window switch Jrom the door
panel, then connect it to the door harness (see page
20-16).
Lower the glass Iully.
Peel off the channel guide cover, then remove the
screws.
NOTE: When installing the channel guide cover, ap
ply the double-faced adhesive tape to it.
>: Screw locations, 3
CENTER CHANNELGUIDE
Remove the center channel guide by pulling it
upward.
Ofimnrrrn
20-10
6. Carefully move the glass until you can see the bolts,
then loosen them.
Slide the guide to the rear, then remove the glass
from the guide.
NOTE: Take care not to drop the glass inside the
door.
: Bolt locations, 2
ffi
/\
BOLT GUIDE
+il€+
/\
GUIDE BOLTLoosen.
GLASS

)7.Carefully pull the glass out through the window slot.
NOTE:
a Take care not to drop the glass inside the door.
a Check the guide pin for damage, and replace it
it necessary.
NOTEr Scribe a line around the guide pin to show
the original location.
GUIDE PIN
GUIDE PINMOUNTING BOLT6 r 1.0 mm3 N.m lO.3 kgl m,2 tbf.trl
GUIDE PIN
GUIDE PIN
SEAL
20-11
Disconnect the connector, then remove the regula-
tor through the center hole in the door.
NOTE: Scribe a line around the rear roller guide bolt
to show the original adiustment.


: Bolt locations, 6
6x1.0mmI N.m {0.8 kgf m6lbt.ftl
REGULATOR
(cont d)

Doors
Glass/Regulator/Glass Run Channel Replacement (cont'd)
9. Remove the power window motor from the
regulator.
NOTE: Before removing the power window motor,
mark the location by scribing a line across the sec
tor gear and regulator.
V: Bolt locations, 3
Qp o"r.o--
El 7Nm(0.7ksf m.
Fl 5 lbf ftls?/:,/
Detach the clips, then peel and remove the glass run
cnanner.
> : Clip locations, 3
10.
GLASS STOPPER
FRONT CHANNEL
CENTEB CHANNEL
20-12
11.
NOTEr lf necessary, remove the glass stopper.
When installing the glass stopper, align it with the notch
in the outer weatherstrip.
Grease allthe sliding surlaces of the regulator where
shown. Install the power window motor on the
regulator.
Check that the regulator moves smoothly by con
necting a 12 V battery to the power window motor
(see section 23).
d
S*--.--;HERwrNDow
-Rt-/'
REGULATOR

12. Apply clear sealant to locations @ on the door as
shown, then install the glass run channel.
NOTEI
a lf necessary, replace any damaged clips
>: Clip locarion, 3
Fit the glass run channel into the front channel
and on the door as shown.
Outside
CENTER CHANNEL
I
\.-, I
lffi, I/{ - ll r- Forward
rlc€\
/, \
nro.r(r" ,*), ""o**..CHANNEL
GLASS RUNCHANNEL
Outside
l---.*',
Install the regulator (see page 2O 11).
NOTE: Make sure the conneclor is connected
properly.
't 3.
20-13
14.
t3,
to.
Install the glass (see page 20 1Oi.
lnstall the center channel guide and channel guide
cover.
NOTE: Make sure the guide pin is installed in the
center channel guide properly.
GUIDE PINGLASS
CHANNEL GUIDE
Roll the glass up and down to see iI it moves freely
without binding. Also make sure that there is no
clearance between the glass and glass run channel
when the glass is closed. Adjust the position of the
glass as necessary lsee page 20 16).
GUIDE PINGLASS
CENTERCHANNELGUIOE
17.
18.
CENTEB CHANNEL
Attach the door harness to the door correctly (see
page 20 5).
Disconnect the power window switch from the door
harness, then install the power window switch on
the door panel (see page 20 16).
19. When reinstalling the plastic cover, applY adhesive
along the edge where neccessary to malntaln a con-
tinuous seal and prevent waler leaks (see page
20 6).
20. Install the door panel (see page 20 4).
GLASS RUNcxlrurutL \..
Er
FRONT CHANNEL

Doors
Front and Center ChannelReplacement
NOTE: Raise the glass tully.
L Remove:
a Door panel (see page 2O-4)
a Plastic cover (see page 2O-4)
2. Remove the front and center channels.
<: Bolt locations, 2
6xLomm I
GLASS RUNCHANNELPeel it out offront channel.
14. Installation is the reverse of the remova I procedure.
NOTE:
a Fit the glass run channels into the front and center
channels as shown.
CENTER LOWERGLASS RUN
Installthe center channel while pushing the glass
as shown.
Make sure the glass run channels are not twisted.
Peel the center lower glass run channel out of the
center channel.
NOTE: When installing, apply clear sealant to loca-
tions @ on the center channel.
GLASS RUNCHANNEL
)_
ffiil
\wdJ
outsid6 t-\
I FRONT
I CHANNEL
L- Forward
20-14

Outer Molding Replacement
CAUTION: Wear gloves to remove the outer molding.
1. Remove the power mirror (see page 20-49).
2. Lower the glass.
3. Starting at the rear, pry the outer molding up and
detach the clips, then remove the outer molding.
NOTE: Take care not to twist or scratch the outer
mold ing.
A : Clip locations, 6
OUTERMOLDING
CLIP
4. Installation is the reverse of the removal procedure.
NOTE:
a It necessary, replace any damaged clips.
a When installing, align the rear edge ot the outer
molding with the rear edge of the door.
OUTER MOLDING
i ---.-__ \.='''- c;,-1
i--,'
NOTE:
a Before installing the inner weatherstrip, apply clear
sealant to locations @ on the door as shown.
a It necessary, replace any damaged clips.
Sealant: Cemedine #8500, or equivalent
>: Clip locations, 21L l : Clip location, 1
.e
Inside
INNERWEATHERSTRIP
WEATHERSTRIP
DD
oo(,)
INNER WEATHERSTRIP

r
Doors
Glass Adjustment
< : Screw locations, 5
"od} l-,/
NOTE:
a Place the vehicle on a firm, level surface when adjust-
ing the glass.
a Check the weatherstrips and glass run channel for
damage or deterioration, and replace them iI
necessarY.
1 . Remove the door panel, and peel off the plastic cover(see page 20 4).
2. Remove the power window switch from the door
panel.
DOOR PANEL
3.Connect the power window switch to the door
harness.
Make sure the guide pin is installed in the center
channel guide properly.
CENTER CHANNELGUIDE
GUIDE PIN
20-16
5. Raise the glass as iar up as possible, and hold it
against the glass run channel.
6. Loosen the roller guide bolts, and adjust the glass
so it is parallel with the glass run channel.
GUID€PIN
CENTEBCHANNELGUIDE
ROLLER GUIDE BOLTS
7. Tighten the roller guide bolts.
8. Check that the glass moves smoothly.
9. It necessary, adjust the lront and center channels.
CHANNEL
GLASS RUN CHANNEL
D\

'to.
11.
Raise the glass fully and check Ior gaps.
Check the glass operation.
NOTEi Check that the glass contacts the glass run
channel evenly.
12. Check for water leaks.
NOTE: Do not use high-pressure water.
13. Route the door harness and connectors, and fasten
them to the door (see page 2O-5).
Disconnect the power window switch lrom the door
harness, then installthe power window switch in the
door panel (see page 20 l6).
Attach the plastic cover, then install the door panel
(see page 2O-4).
14.
20-17