1998 HONDA INTEGRA Workshop Manual

Doors
Door lndex
HatchbackOUTER MOLDINGReplacement, Page 20 15OUTER WEATHERSTRIPReplacement, page 20-1 5
INNER WEATHERSTRIPReplacement, page 20-1 5
POWER MIRRORReplacement, page 2o-49
COVER PANEL
PLASTIC COVERReplacement, Page 20 4
HINGE
I
ffis
,ad
mr
,tA g
lF
T ROD
DOOR PANELReplacement, page 20 4
i'-t"-
lGN=*sS)
20-2
SPEAKER COVER

GLASSReplacement, page 20,10Adjustment, page 20-16
GUIDE PIN
CENTER CHANNELGUIDE
,**ry
R
\-_-..........-..-.-,*oNr .HANNEL
* #
Replacemenr. pase 20 14
OUTER HANDLE
mw
&p.'
\
POWER DOORLOCK SWITCH
c9INNER HANDLEROD
INNER HANDLETRIM
Replacement,page 20-10
CENTER LOWERGLASS RUN CHANNELReplacement, page 20-14
@
LOCK CYLINDER
REGULATORReplacement,page 2O-10
POWER WINDOWMOTOR
W
/-%
STFIKERAdjustment,page 20-48
@
ROD PROTECTOR
20-3

Doors
Door Panel/Plastic Cover Replacement
NOTE: Take care not to scratch the door panel and other
parts.
1. Pry out the cap and remove the screw
<: Screw location,l
Remove the inner handle trim while pulling the inner
handle.
Disconnect the power door lock connector.
'l
I
i
20-4
3.Remove the armrest Pocket.
v : Screw location, I
/eF\
YIv//
ARMRESTPOCKET
4. Release the clips that hold the door panel.
NOTE: Remove the door panel with as little bend
ing as possible to avoid creasing or breaking it'
95 mm {3.74 inl
nYLf*P to.ci int r-
-L<------=-r-
132\. .-2=---REMOVERSNAP-ON#4177, orequivalent
11.77 in)
<: Clip locations
TRIM PADREMOVERthen remove the clip usinga trim pad or clip remover-

5.Remove the door panel by pulling it upward.
Disconnect the f ollowing:
a Power window connectora Power mirror connector
a Tweeter connector
POWER MIRRORCONNECTORPOWEB WINDOWCONNECTOR
Remove the bracket and door lock unit. lf necessary,
remove the {ront speaker. Disconnect the con
nectors.


: Screw locations, 8
DOOR LOCK UNIT
FRONT CONNECTORSPEAKER
6.
PLASTIC COVER
7.Remove the cover panel, then disconnect the power
mirror connector (see page 20 49)
Detach the grommets and harness clips, then care
fully remove the plastic cover.
a: Grommet locat;ons, 2 Q: Harness cliplocations,3
GROMMET
BeJore installing the plastic cover, make sure the
door harness and connectors are {astened correctly
on the door.
a : Connector clip locations, 3
O: Harness clip locations, 7
8.
A
9.
DOOR HABNESS
20-5

Doors
Door Panel/Plastic Cover Replacement (cont'dl
1O. Install the plastic cover.
NOTE:
a Apply adhesive along the edge where necessary
to maintain a continuous seal and prevent water
leaks.
a Do notJ)lug the elongated hole.
AOHESIVE
:
Pass the door harnessthrough the hole of theplastic cover.
PLASTICCOVEB
1 l Install all removed oarts, and fasten the door harness
correctly.
a: Grommet locations, 2Or Harness cliplocations,3
GROMMET
PLASTICCOVERFRONTSPEAKER
DOOR LOCK UNIT
20-6
ARACKET
12. lnstall the door panel (see page 2O-4).
NOTE:
a lMake sure the door harness is not pinched.
a lf necessary, replace any damaged claps.
a Make sure the connectors are connected properly.
'13. Inslallthe armrest pocket and inner handle trim (see
page 2O-4).
NOTE: Make sure the connector is connected
properly.

Outer Handle Replacement
NOTE: Raise the glass fully.
1. Remove:
a Door panel (see page 2O-4)
a Plastic cover (see page 20 4)
2. Remove the rod protector.
>: Screw localion, 1
INNER HANDLEROD
Push here.
Lalch srde.Rod protector side.
3. Disconnect the connector, and remove the harness
clamp and clips.
>: Screw location, 1
CONNECTORDetach the connector{rom the door.
8OD PFOTECTOR
4. Remove the bolts.
>: Bolt locations, 2
6 x 1.0 mm9.8 N.m {1.0 ksf m.1 .2 thl.tt)
5.Pull out the outer handle.
Pry the outer handle rod out of its joint using diagonal
cuners.
NOTE:
a To ease reassembly, note location @of the outer
handle rod on the joint before disconnecting it.a Take care not to bend the outer handle rod.
a Use a shop towel to protect the opening in the
door.
BUSHINGReplace.
h
SHOP TOWEL
(cont'd)
20-7

Doors
Outer Handle Replacement (cont'dlLatch Replacement
NOTEr Raise the glass fully.
'1. Remove:
a Door panel (see page 20 4)
a Plastic cover lsee page 20-4)
a Outer handle (see page 20 7)
2. Disconnect the inner handle rod and lock rod from
the latch.
Detach the inner handle rod and lock rod, then
remove the inner handle.
NOTE: Take care not to bend the rods.
>: Screw locations, 2
@t" ,
J
INNER HANDLEROD
INNER I{ANDLE
-1"'-
\
\LOCK ROD
)
INNER HANDLEROD
6.
8.
Disconnect the cylinder rod as shown.
NOTE: Take care not to damage the lock cylinder
joint.
OUTERHANDLECYLINDERROD
7.
V
SHOP TOWEL
Remove the cylinder switch lrom the outer handle.
: Scrsw location, 1
OUTERHANDLE
i4) cYLtNDERswtTcH
Pull out the retainer clip, then
cylinder and cylinder protector.
LOCK CYLINDER
li) clrPReplace
S*-.o"* .YLTNDER
CYLINDERPROTECTOR
RETAINERCLIP
Installation is the reverse of the removal procedure.
NOIE:
a Make sure the outer handle rod and connector are
connected securely.
a Make sure the wire harness is routed properly.
a Make sure the door locks and opens properly.
20-8

3. Loosen the bolt, then move the center channel
outward.
>: Bolt location, 1
6 x 1.0 mm8Nm {0.8kglm, I"*'l____)
CENTERCHANNEL
4.Disconnect the connector, and detach the harness
clip from the door.
Remove the screw,
>: Screw locations, 3
6x1.0mm IfiNrrlr
nr 6 N m (0.6 kgfm '
law iw.r,i )
CONNECTORDetach the connector.
5. Remove the latch through the hole in the door.
NOTE: Take care not to bend lhe outer handle rod
and cylinder rod.
CYLINDERROD
6. lnstallalion is the reverse of the removal procedure.
NOTEI
a Make sure the inner handle rod, lockrodandcon-
nector are connected properly.
a Make sure the door locks and opens properly.
20-9