1998 HONDA INTEGRA Workshop Manual

Lighting System
OAYTIMERESISTOR (Can.dal
Test, page 23-168
HEADLIGHTS
Component Locations Index
HIGH BEAM INDICATOR LIGHT{ln the galge assembly}Bulb Locations. page 23-122
COMAINATION LIGHT SwlTCHReplscement, page 23-168Test, page 23-162
Adjustment, page 23-170Replacement, page 23-170
CONTBOL UNIT {Can.d.)Input, Test page 23-164
23-160

!/ Hatchback:
Sedan:
LICENSE PALTE LIGHTSReplacement, page 23-177
TAILLIGHT. Replacement, page 23 174. Bulb r€placement, page 23-174
LICENSE PALTE LIGHTSReplacement, page 23-177
INNER TAILI-IGHT. Replacement, page 23-175. Bulb replacement, page 23-176
. Replacement, page 23-175.8ulb replacement, page 23'176
23-161

Lighting System
Circuit Diagram (USA)
R€O/BtK
I
REO/BLKIII
I
. OASH LIGHTSBFIGI.ITNESSCONTROLLER. DASH TIGHTS
RED/CRN
I
Ailsurax
Yller,l
IBL(
I
I
I-l
G201G401
. PANK NG L GNTS.TA LL GHTS. LICENSE PLATELIGHTS
UNDER.HOOD FUSE/RELAY BOX
RED]BtU
N0.21(104)No.5{10A)
III No22 I No4( lroA) ( {1oA)
IT
INo30 :(7.5A) (
I
N0.3200A)
8LK
I
G20lG40l
23-162

UNDER.HOOD FUSE/RELAY BOX
No 41 {100A) N0.42 (40A)
,/ |\
\--, ({c)
HEADLIGHT
Circuit Diagram (Canada)
BATTEFY
@-**
I I :i,ff'*''"
I CoNTFOL UN|TI . INTEGBATED
l-v^"
tl
tlREDAVHT GRN/RED
GRN/FED
L
lt ))
Yro^,
I iivP,
I
swrrcH
BLK
I
I-l
G301
RED/GFN
tGRN/RED
A
Y*r*ro
I
3Ai{5"
I
I
I
DAYTIME BUNNINGL]GHIS RESISTOR
UNDER.DASHFUSE/FELAY BOX
) No.21
i
uoo') N0.20{JOA))'
) N0.18(7.5A))'
II
lrrt,
llrffi ltlrr
INo.3o Q
(7.sA) . (
I
N0.32(104)
RED GqN RED YE- RED BL- REDTVHT FED/BLK REO/8LK WHT/YEL YEUBLK
| + +ll
I
i*n[i+'i .ffi$liilTl
II ri---J- i---F BEDE-U +1 4- l^ |
l,,oo,* *qff
.'""0
{36['45,1'il]''
23-163

Lighting System
Daytime Running Lights Control Unit Input Test (Ganada)
Remove the dashboard lower cover and knee bolster.
Disconnect the connectors from the daytime running
lights control unit.
Inspect the connector and socket terminals to be
sure they are all making good contact.
a lf the terminals are bent, loose or corroded. repair
them as necessary, and recheck the system.
a ll the terminals look OK. make the lollowing in-
put tests at the connector.
lf any test indicates a problem, find and cor-
rect the cause, then recheck the system.
lf all the input tests prove OK, the control unit
must be faulty; replace it.
4P CONNECTOR8P CONNECTOR
GNN/RED
WHTiRED
WHT/YEL
REO/WHTRED/GRN
YEL/BLK
23-164
View trom wire sideView from wire side

Tsst conditionTest: Desiled resultPossible cause it result is not obtained
)
BLKUnder all conditionsCheck for continuity to ground:
There should be continuity.
. Poor ground (G201 , G40l ). An open in the wire
2WHT/YEL
Under all conditionsCheck for voltage to ground:
There should be battery voltage.
. Blown No. 20 (10 A) fus€ in the
under-dash fuse/relay box. An open in the wire
YEL/BLK
lgnition switch ON (ll)Check for voltage to ground:
There should be battery voltage.
Blown No. 18 (7.5 A)fuse in the
under-dash fuse/relay box
Faulty ignition switch
An open in the wire
RED/WHT
Combination light
switch in "=D" position
Check for voltage to ground:
There should be battery voltage.
Blown No. 48 (40 A) fuse in the he
under-hood fuse/relay box
Faulty combination light switch
An open in the wire
WHT/RED
Combination light
switch is OFF; connect
a jumper wire between
the YEL/BLK and
WHT/RED terminals,
then turn the ignition
switch ON (ll).
Left and right headlight (high
beaml should be on but dim, and
high beam indicator light should
come on.
Poor ground (G20'1, G4O1, G301)
Blown bulbs
Faulty daytime running lights
resrstor
An open in the wire
6GRN/RED
lgnition switch ON (ll).
brake fluid reservoir
full, and parking brake
levef oown
Connect to ground: The b.ake
system light should come on.
Blown No. 25 (7.5 A) fuse in the
under-dash fuse/relay box
Blown brake system light
An open in the wire
'1RED/GRNParking brake lever upCheck for continuity to ground:
There should be continuity.
. Faulty brake lever switch. An open in the wire
23-165

Lighting System
Combination Light/Turn Signal Switch Test
Remove the dashboard lower cover and steering
column covers {see page 23-721.
Disconnect the 4P and 7P connectors from the
switch.
Check the connector and socket terminals to be sure
they are all making good contact. lf the terminals are
bent, loose, or corroded, repair them as necessary,
and recheck the system.
Check lor continuity between the termanals in each
switch position according to the table.
B
D
E
H
4P CONNECTOR
7P CONNECTOR
23-166

Combination Light Switch :
OFFd
I
.,\
Lr"
G (Not us.d)
Tuln Signal Switch :
Terminal
PositionFJ
Headlight switchOFF
:m:oo
=DLOWo--ooo
HIGHoooo
Passing switchOFF
ONoo
LEFTRIGHT
I
Position
TerminalB
RIGHToo
NEUTRAL
LEFToo
23-167